We serviced a
MAYTAG WASHER-TOPLOAD
Model LAT9734AAE
Near Dallas, TX 75238
Lane
Job Details:
04/25/2024
Customer stated washer stopped mid cycle. Performed diagnostics found faulty timer. Washer also needs to be leveled. Needed parts have been discontinued.
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS0
Near Murphy, TX 75094
Lane
Job Details:
04/25/2024
Customer stated dishwasher wouldn't drain. Performed diagnostics found drain system being choked by a adapter for a water filtration system. Repair is not covered due to modification of drain system. Drain hose should be changed and ran directly to disposal. Water filtration drain would need to be tied into plumbing by a plumber. Estimate to replace hose $290.83 + tax.part#W11414944
We serviced a
MIDEA WASHER-TOPLOAD
Model MLV45N3BMG
Near Irving, TX 75063
John
Job Details:
04/25/2024
"Installed new motor, pulley, and belt. All checks good."
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS0
Near Puyallup, WA 98372
Cejay
Job Details:
04/25/2024
"Customer concern is that dishwasher is showing error, and is leaking. Found leak from Left rear heater bushing, service bulletin for bushing replacement. Pulled error codes, F9E1. Drain motor is operational, recommend replacing drain motor to start. Needs updated heating element for leak. Customer declined repair at time of service. Collected payment via card."
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW8127LC1
Near Tacoma, WA 98408
Cejay
Job Details:
04/25/2024
"Customer concern is that stick is broken. Confirmed customer concern, strike is damaged causing washer not to operate. Installed new lid strike, manually cycle lock multiple times via service mode, all checks good."
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW6120HW0
Near Orting, WA 98360
Cameron M.
Job Details:
04/25/2024
"Customer concern is that washer produces noise during operation. Cycle tested unit. Found worn belt and pully causing belt slip during spin cycle. Needs new cam and belt. Installed new cam and belt. Cycle tested unit. All checks good. ; used 1 W10721967 (CAM), and 1 W11239857 (BELT) from stock"
We serviced a
MAYTAG DRYER-ELECTRIC
Model MEDB766FWO
Near Graham, WA 98338
Cameron M.
Job Details:
04/25/2024
"Customer concern is that dryer does not heat. Preformed airflow test, failed. Tested continuity of heating components, found open element causing unit to not heat. Needs new element installed new element. Cleaned and vacuumed inside of unit. Corrected vent hose. Cycle tested unit. All checks good ; used 1 279838 (ELEMENT,HEATER) from stock"
We serviced a
SAMSUNG REFRIGERATOR
Model RF29A9671SR/AA09
Near Forney, TX 75126
Patrick
Job Details:
04/24/2024
"Custody concern, ice bites mold broken. Confirmed. Replaced im from preorder. Tested unit. Checks good. Return filter head assy."
We serviced a
GE DISHWASHER
Model PDW7880N10SS
Near Dallas, TX 75204
Lane
Job Details:
04/24/2024
Customer stated dishwasher doesn't drain. Performed diagnostics found airgap clogged. Cleared airgap and performed several function tests. All functions checked good at time of service.
We serviced a
KENMORE DRYER-ELECTRIC
Model 110.64202200
Near Puyallup, WA 98371
Cameron M.
Job Details:
04/24/2024
"Customer concern is that dryer does not start cycle. Tested voltage supply to unit, good 240v. Tested continuity of heating components. Found open thermal fuse, causing unit to not heat. Needs new fuse. Installed new thermal fuse. Cleaned and vacuumed inside of unit. Cycle tested unit. All checks good collected payment via card ; used 1 WP3392519 (FUSE-THRML) from stock"
We serviced a
WHIRLPOOL REFRIGERATOR
Model GR2FHMXVY03
Near Richardson, TX 75082
Patrick
Job Details:
04/23/2024
"Found fill tube insertion to valve worn preventing proper seal. Trimmed end and reinserted. Unit cycled, no leak noted."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS2623AD8
Near Dallas, TX 75253
Patrick
Job Details:
04/23/2024
Replaced im. All checks good
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVW7230HW1
Near Garland, TX 75043
Lane
Job Details:
04/23/2024
Installed new harness with pump. Performed multiple function tests after repair. All functions checked good at time of service.
We serviced a
GE DRYER-ELECTRIC
Model GTX22EASK0WW
Near Tacoma, WA 98443
Cejay
Job Details:
04/23/2024
"Installed previously ordered door assembly, preformed airflow test failed (yellow). Advised dryer vents need service."
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WF337AAL/XAA
Near Puyallup, WA 98373
Cameron M.
Job Details:
04/23/2024
"Customer concern is that washer produces out of balance condition after moving. Attempted to Pull errors via service mode, found no stored errors. Cycle tested unit empty. Unit produces normal tub movement during 0-100 rpm range during mid range rpms unit balances with little to no deflection in high speed spin unit produces high degree of tub deflection causing cancelation of cycle. Preformed inspection of unit, found leaking and heavily corroded inlet valves unrelated to movers. Found shipping bolts were Attempted but improperly installed causing damage to mounting locations. Inspected tub assembly for excess basket play and deflection, no defect found. Found balance ring responsible for aiding in balance. Cracked leaked oil out, causing unit in ability to preform spin cycle adequately due to tub improperly secured during transport. Needs new inlet assembly, and basket assembly. Due to parts showing NLA no repair available at this time. Collected diagnostic fee +tax via card payment"
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WA55A7700AV/US
Near Rockwall, TX 75032
Patrick
Job Details:
04/19/2024
Replaced door lock. Unit began cycle normally. All checks good.
We serviced a
LG WASHER-FRONTLOAD
Model WM8100HVA
Near Mesquite, TX 75150
John
Job Details:
04/19/2024
Customer concern is door will not close and door boot and retainer have come off. Confirmed door will not close due to boot being in the way. Reinstalled boot and retainer. Door now closes properly. Ran full service cycle. All checks good.
We serviced a
MAYTAG DRYER-ELECTRIC
Model MEDB835DC4
Near Spanaway, WA 98387
Cejay
Job Details:
04/19/2024
"Customer concern is that dryer is making a noise durring operation. Found failed RR roller, other rollers and idler sticky, found front and rear drum seals damaged. Needs new RR rollers and shaft, front and rear drum seals and idler, clean and lubricate remaining rollers. Customer declined repair at time of service. Collected payment via card."
We serviced a
MAYTAG WASHER-FRONTLOAD
Model MHW5630HC
Near Dallas, TX 75253
Patrick
Job Details:
04/18/2024
"Customer concern, unit will not drain. Confirmed. Cleared clogged drain catch. Ran test cycle. Unit checks good at this time."
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ0
Near Dallas, TX 75244
Lane
Job Details:
04/18/2024
Customer stated dishwasher is forming film and buildup inside dishwasher and on items washed. Advised running a citric acid based cleaning agent to remove buildup and improve wash quality. All functions checked good at time of service.
We serviced a
KITCHENAID DISHWASHER
Model KDTE104KPS1
Near Garland, TX 75044
Chad A.
Job Details:
04/18/2024
Customer stated dishwasher not completing cycle. During testing found pump filter blocked and not draining. Cleared filter and still not draining and poor pump pressure. Need pump assembly and drain hose.
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5241SR/AA51
Near Plano, TX 75094
Chad A.
Job Details:
04/18/2024
Replaced ice maker and auger assembly. Cycled ice maker and water fill checked good.
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model WED8000DW4
Near Lakewood, WA 98498
Cameron M.
Job Details:
04/18/2024
"Customer concern is that dryer produces metal on metal scraping sound. Inspected drive components. Found seized idler pully. Causing noise during operation. Inspected drum felt for debris, clear Inspected rollers ,needs cleaning and lubrication. Inspected wheel for deformation or cracking, intact. Needs new idler pully. Installed new idler pully. Cleaned and lubed rollers. Vacuumed inside of unit. Cleaned and calibrated moisture sensor. Cycle tested unit. All checks good ; used 1 W10837240 (BRACKET) from stock"
We serviced a
GE WASHER-FRONTLOAD
Model GFW850SPN0RS
Near Carrollton, TX 75007
Lane
Job Details:
04/17/2024
Cstated washer wouldn't drain or unlock door. Performed diagnostics found clogged pump. . Cleaned out foreign debris and performed multiple function and leak tests. All functions checked good at time of service.
We serviced a
KENMORE DRYER-ELECTRIC
Model 11065922401
Near Carrollton, TX 75007
John
Job Details:
04/17/2024
Installed new even heat board. Temp checked all settings. All checks good.
We serviced a
KITCHENAID WALL OVEN
Model KEBS208SSS00
Near Wylie, TX 75098
Chad A.
Job Details:
04/17/2024
Replaced upper oven broil element. Cycled bake and broil and both functioning properly.
We serviced a
SAMSUNG DISHWASHER
Model DW80R5060US/AA 00
Near Puyallup, WA 98374
Cejay
Job Details:
04/17/2024
"Customer concern is that dishwasher is turning on by itself. Water in leak tray apon arrival. Cycle tested unit for leak diagnosis for 40 minutes could not replicate leak. Possible oversuds condition, Dedergent stains on floor. Advised customer on using high quality detergent and running regular cleaning cycles. No mechanical or component failures at time of service."
We serviced a
GE DISHWASHER
Model GDF520PGJ5WW
Near Spanaway, WA 98387
Cejay
Job Details:
04/17/2024
"Customer concern is that dishwasher is not powering on. Confirmed 13.5vdc from control, found failed UI causing unit not to operate. Needs new configured UI board. Customer declined repair at time of service. Collected payment via card."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ03
Near Garland, TX 75043
Patrick
Job Details:
04/16/2024
"Replaced door sw, tested unit. All checks good"
We serviced a
SAMSUNG WASHER-TOPLOAD
Model WF45R6300AV/US
Near Dallas, TX 75227
Patrick
Job Details:
04/16/2024
"Replaced control and drain pump. Tested unit, spin, good, quick wash, all checks good"
We serviced a
SAMSUNG WASHER-TOPLOAD
Model WA40J3000AW/A2 01
Near Garland, TX 75040
Lane
Job Details:
04/16/2024
Customer stated washer would not complete cycle. Performed function test with load. Washer operating correctly att time of service. Possible out of balance condition. Leveled washer and advised customer on load size and out of balance condition.
We serviced a
KITCHENAID DISHWASHER
Model KDFM404KPS0
Near Garland, TX 75044
Lane
Job Details:
04/16/2024
Customer stated dishwasher stopped running and didn't drain. Performed diagnostics found supply voltage problem. Customer needs electrician to correct supply voltage.
We serviced a
KENMORE WASHER-FRONTLOAD
Model 79641532210
Near Dallas, TX 75287
Lane
Job Details:
04/16/2024
Customer stated washer failed to turn on. Prior diagnosis was performed attributingt main control.failure. Washer at time of service is working to manufactures specifications. Advised customer to continue to use washer for now. If washer fails to power on in the future main control needs to be replaced with noise filter. All functions checked good at time of service.
We serviced a
GE WALL OVEN
Model JT3000SF3SS
Near Wylie, TX 75098
John
Job Details:
04/16/2024
Installed new broil element and control board. All checks good.
We serviced a
GE WASHER-TOPLOAD
Model GTW720BSN1WS
Near Garland, TX 75040
Chad A.
Job Details:
04/16/2024
Replaced main control and informed customer on how deep fill option works. Tested and found washer working properly and ready for use.
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model WED5100HC0
Near Tacoma, WA 98445
Cejay
Job Details:
04/16/2024
"Customer concern is that dryer is not heating but turns on. Preformed airflow test pass. Found dryer is only receiving 120v at terminal. Visually inspected outlet for damage, cycled breaker and checked power at outlet, 240v. found weak breaker causing dryer not to heat. Advised customer electrician is needed. Sent payment link via text."
We serviced a
KENMORE DISHWASHER
Model 66513103K901
Near Edgewood, WA 98371
Cameron M.
Job Details:
04/16/2024
"Customer concern is that dishwasher leaks through subfloor, customer advised leak caught by home inspection service. Preformed visual inspection of unit plumbing hookups, drainhoseand inlet. Clear and dry. Cycle tested unit found no mechanical defects of unit. Unit operating as designed."
We serviced a
GE WASHER-TOPLOAD
Model GTWN425D1WS
Near Tacoma, WA 98408
Cameron M.
Job Details:
04/16/2024
"Customer concern is that washer does not rinse and spin. Cycle tested unit empty, unit completed rinse and spin cycle without issue. Cycle tested unit with customer provided load of 5 towels and assorted wash rags. Unit completed without issue preformed cycle test of unit with different wash settings ,i.e water temp, fill level, and different cycle selections. Unable to duplicate customer concern of unit not rinsing and spinning. Advised customer to monitor load volume, water level and cycle settings in future should issues persist. Advised customer to record video if possible. Collected 129 +txw via"
We serviced a
KITCHENAID DISHWASHER
Model KDTE104ESS4
Near Bonney Lake, WA 98391
Cameron M.
Job Details:
04/16/2024
Installed previously ordered spray arm cycle tested unit. All checks good.
We serviced a
ELECTROLUX DISHWASHER
Model FGIP2468UF0A
Near Orting, WA 98360
Cameron M.
Job Details:
04/16/2024
Installed previously ordered spray arms. Cycle tested unit. All checks good. Customer declined to retain old part.
We serviced a
GE DRYER-ELECTRIC
Model GTD33EASK0WW
Near Rowlett, TX 75088
Lane
Job Details:
04/15/2024
Replaced vent hose and confirmed dryer is heating. . Dryer ventilation tested moderate (yellow). No signs of significant lent buildup in dryer or vent extension coming out of wall. All functions checked good at time of service. ; used 1 BTD48 (4: X 8' FLEX DUCT) from stock
We serviced a
LG REFRIGERATOR
Model LFXS26973S/10
Near Forney, TX 75126
Lane
Job Details:
04/15/2024
Customer stated freezer is building up ice. Performed diagnostics found faulty door gasket. Replaced gasket and adjusted left side door higher for center flap to align properly. All functions checked good at time of service.
We serviced a
GE WALL OVEN
Model JTP14W0V2WW
Near Plano, TX 75093
Chad A.
Job Details:
04/15/2024
Replaced bake element and cycled to test. All components functioning properly and no other failures detected.
We serviced a
GE WASHER-FRONTLOAD
Model GFW650SPN2SN
Near Plano, TX 75075
Chad A.
Job Details:
04/15/2024
Replaced dispenser housing assembly due to leaking water. Cycled to test and functioning properly.
We serviced a
GE WASHER-FRONTLOAD
Model GFW850SPN0DG
Near Corinth, TX 76208
Chad A.
Job Details:
04/15/2024
Cycled to test and found door lock functioning but main control not reading signal properly. Replaced main control and performed full cycle. All working properly and no other failures detected.
We serviced a
SAMSUNG RANGE
Model NX60A6111SS/AA
Near Parkland, WA 98445
Cejay
Job Details:
04/15/2024
"Customer concern is that range display is not working. Confirmed 120v to main control, found failed control board causing oven not to operate. Needs new control board. Advised control board is back ordered and will take time to recive. Custome4 declined repair at time of service. Collected diagnostic fee via card."
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model n/a
Near Bonney Lake, WA 98391
Cejay
Job Details:
04/15/2024
"Customer concern is that washer is making a strange noise durring rinse and spin. Model tag is worn. No stored errors, via service mode, confirmed operation of all washer functions, preformed calibration cycle, cycle tested unit on rinse and spin, no noise. Visually inspected belt and cam, found signs of wear on belt and cam causing noise with a load, needs new belt and cam. Installed new belt and cam assembly, preformed calibration cycle, all checks good. ; used 1 W10721967 (CAM), and 1 W11239857 (BELT) from stock"
We serviced a
KENMORE WALL OVEN
Model 79048132801
Near Orting, WA 98360
Cejay
Job Details:
04/15/2024
"Installed previously ordered hidden bake element on lower oven, cycle tested unit to verify repair, all checks good. Advised customer of unsecured ground wire, advised electrician is needed for ground. Collected payment via check."
We serviced a
LG WASHER-FRONTLOAD
Model WM4270HVA
Near Puyallup, WA 98373
Cameron M.
Job Details:
04/15/2024
Customer concern is that washer does not close. Preformed inspection. Found door boot disengaged from unit preventing door from closing. Re secured door boot. Cycle tested unit. All checks good. Advised customer on regular cleaning intervals. Advised customer on using high quality detergent.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAHZ0
Near Federal Way, WA 98003
Cameron M.
Job Details:
04/15/2024
Customer concern is that dishwasher does not wash. Preformed cycle test of unit. Found dead spot in wash motor. Causing unit to not wash. Needs new sump asm. Customer declined repair. Collected 129+ tax via card payment
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS0
Near Bonney Lake, WA 98391
Cameron M.
Job Details:
04/15/2024
Installed warranty provided parts. Cycle tested unit all checks good
We serviced a
KENMORE WASHER-TOPLOAD
Model 11027072602
Near Spanaway, WA 98387
Cameron M.
Job Details:
04/15/2024
Installed previously ordered bearing. Cycle tested unit. All checks good.
We serviced a
GE DISHWASHER
Model GDF610PSJ0SS
Near Dallas, TX 75244
Patrick
Job Details:
04/12/2024
"Customer concern, unit not draining. Confirmed. Tub full on arrival. Cleared drain impeller, reassembled, all checks good."
We serviced a
KENMORE WASHER-FRONTLOAD
Model 79641262610
Near Plano, TX 75023
John
Job Details:
04/12/2024
Installed new control board and pressure switch supplied bt Sears. All checks good.
We serviced a
ELECTROLUX WASHER-FRONTLOAD
Model ELFW7537AW1
Near Spanaway, WA 98387
Cejay
Job Details:
04/12/2024
"Customer request replacement of dryer vent hose and needs new dryer power cord and installment of washer. Installed new 30amp 3 wire dryer power cord, flex duct and two clamps on dryer. Preformed airflow test pass. (28 Pa). Temperatures checks good. Leveled washer and installed water supply lines to their proper inlets, installed and secured drain line, preformed service diagnostic cycle to verify install, pass. Collected payment via check. ; used 1 BTD48 (4: X 8' FLEX DUCT), 1 WX09X10003 (POWER CORD 5' 30A 3WIRE DRYR), and 2 MC450 (4' WORM CLAMP) from stock"
We serviced a
GE DISHWASHER
Model PDW7300N15BB
Near Eatonville, WA 98328
Cejay
Job Details:
04/12/2024
"Customer concern is that dishwasher middle spray arm has fallen, middle spray arm not mounted apon arrival, spray arm is undamaged, recounted spray arm, unable to cycle tested due to leak at water shut off valve, advised plumber is needed. No parts needed."
We serviced a
GE DISHWASHER
Model GSD3360D35SS
Near Tehaleh, WA 98391
Cameron M.
Job Details:
04/12/2024
Customer concern is that dishwasher does not power. Found unit powers and starts cycle. Cycle tested unit 5x Found evidence of past leak. Found no active leaks at time of service. Advised customer to monitor and call if issues persist. Collected 129 + tax
We serviced a
OTHER REFRIGERATOR
Model 590
Near Plano, TX 75093
Lane
Job Details:
04/11/2024
Installed new replacement subzero style ice maker. Performed cycle and fill test. Water level is within manufacture specifications . All functions checked good at time of service.
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMELBSR/AA 01
Near Dallas, TX 75218
Chad A.
Job Details:
04/11/2024
"Customer stated display not functioning and ice maker frozen over. Tested and found good voltage through door switches to display with no touch function. Needs display assembly, icemaker, and auger assembly. No repair at this time."
We serviced a
LG REFRIGERATOR
Model LFX3596OTT
Near Garland, TX 75043
Lane
Job Details:
04/10/2024
Customer stated refrigerator makes abnormal noise. Performed diagnostics found noise coming from evaporater fan. Parts have been discontinued for this model. Advised customer manual defrost will temporally alleviate issue.
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWX655DW2
Near Dallas, TX 75238
Lane
Job Details:
04/10/2024
Customer stated washer won't spin clothes out. Performed diagnostics found new code for shifter fault. Replaced shifter and performed function test with load. All functions checked good at time of service.; used 1 W10913953 (ACTUATOR) from stock
We serviced a
GE WASHER-TOPLOAD
Model GFW850SPN2RS
Near Dallas, TX 75204
John
Job Details:
04/10/2024
Installed new control board. All checks good.
We serviced a
GE DISHWASHER
Model GDT655SSJ5SS
Near Dallas, TX 75204
John
Job Details:
04/10/2024
Installed new inlet valve. All checks good.
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV448AEW/XAA
Near Carrollton, TX 75007
John
Job Details:
04/10/2024
Customer concern is dryer not heating. Confirmed no heat. Found burnt connector on element and fails continuity. Replaced element assy from truck stock and repaired wire. All checks good.; used 1 DC97-14486A () from stock
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV48H7400EW/A2 01
Near Tacoma, WA 98404
Cejay
Job Details:
04/10/2024
"Installed previously ordered drive motor, cycle tested unit to verify repair, all checks good."
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model WED4850HW0
Near Bonney Lake, WA 98391
Cejay
Job Details:
04/10/2024
"Installed previously ordered motor, pully and belt, cycle test unit to verify repair, all checks good."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV400EWHDWR/AA
Near Tacoma, WA 98498
Cameron M.
Job Details:
04/10/2024
"Customer concern is that dryer produces squealing noise and burning smell during operation. Preformed inspection of unit, found front left and front right rollers heavily worn, causing unit to produce noise during operation. Also found rear right roller worn and produces noise during operation. Also found seized idler pully, causing squealing noise during operation. Found smell customer speaking of is causing by restricted airflow, causing higher than optimal temperatures and causing minor scorching of lint on element housing. Needs new idler pully and rollers. Installed new idler pully and rollers. Cleaned and vacuumed inside of unit. Cleaned and calibrated moisture sensors. Cycle tested unit. Found unit produces noise still. Found debris in rear of unit producing noise. Advised customer vent hose needs to be shortened to allow sufficient air flow. Advised customer vent needs to be cleaned asap before use resumes to prevent damage to heating components. ; used 3 DC97-16782A (DRUM ROLLER), and 1 DC93-00634A (IDLER ASSEMBLY) from stock"
We serviced a
HOTPOINT DISHWASHER
Model HDF330PGR0BB
Near Dallas, TX 75208
Patrick
Job Details:
04/09/2024
"Customer concern, unit will not operate. Find tub full of water on arrival. Drain pump will not pump. Found clogged drain to disposer. Cleared. Tested unit. All checks good."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ03
Near Grand Prairie, TX 75051
Patrick
Job Details:
04/09/2024
Replaced ice maker. Unit checks good.
We serviced a
ROPER DRYER-ELECTRIC
Model RED4516FW0
Near Garland, TX 75043
Patrick
Job Details:
04/09/2024
"Customer concern, unit made clunk noise then stopped drying. Found clogged home vent. Found open element. Replaced from truck stock. Unit checks good at this time. Left disconnected. Customer to have vent professionally cleaned. ; used 1 279838 (Element) from stock"
We serviced a
SPEED QUEEN WASHER-TOPLOAD
Model AWN63RSN116TW01
Near Plano, TX 75093
Lane
Job Details:
04/09/2024
Installed new drive control and belt. Performed multiple function tests. All functions checked good at time of service.
We serviced a
GE DISHWASHER
Model GOD5660N10SS
Near Irving, TX 75039
John
Job Details:
04/09/2024
"Customer concern is DW leaking onto countertop when draining. Found air gap plugged with debris on the drain hose side and disposal side. Cleared clogs and tested. Filled and drained unit 5x times. Good fill, good wash, and good drain. All checks good."
We serviced a
AMANA DRYER-ELECTRIC
Model LEA30AW
Near Dallas, TX 75252
John
Job Details:
04/09/2024
Installed new blower wheel and motor. All checks good.
We serviced a
FRIGIDAIRE DISHWASHER
Model FFCD2413US5A
Near Plano, TX 75074
John
Job Details:
04/09/2024
Cuwtomer concern is DW nit draining. Found end of hose clogged at inlet to disposal. Cleared clog and tested. Filled and drained unit 5x times. All checks good. Advised Customer about how to clean DW and how often.
We serviced a
SAMSUNG DISHWASHER
Model DW80R9950US/AA 01
Near Puyallup, WA 98374
Cejay
Job Details:
04/09/2024
"Installed previously ordered duct assembly, confirmed operation of upper spray arm all checks good."
We serviced a
FRIGIDAIRE COOKTOP
Model FEC32S6HBA
Near Tacoma, WA 98408
Cameron M.
Job Details:
04/09/2024
Installed previously ordered infinite switch. Cycle tested unit. All checks good
We serviced a
MAYTAG DISHWASHER
Model MDB4949SHZ0
Near Graham, WA 98338
Cameron M.
Job Details:
04/09/2024
Installed previously ordered sump asm. Cycle tested unit. All checks good
We serviced a
GE RANGE
Model C2S950P2M2S1
Near Allen, TX 75002
Lane
Job Details:
04/08/2024
Customer stated left front burner wouldn't light and gas could be smelled. Performed diagnostics found burner working at time of service. Customer concernd multiple burners were trying to ignite. Explained to customer ignition system operation. All functions checked good at time of service.
We serviced a
SAMSUNG REFRIGERATOR
Model RF23J9011SR/AA. 08
Near Plano, TX 75023
Lane
Job Details:
04/08/2024
Installed ice maker kit. Performed function test after repair. Advised customer to allow time fot ice maker to produce.all functions checked good at time of service.
We serviced a
LG WASHER-FRONTLOAD
Model WM2050CW
Near Coppell, TX 75019
Chad A.
Job Details:
04/08/2024
Replaced stator and door gasket. Cycled to test with load and all functioning properly. No other failures detected.
We serviced a
GE RANGE
Model JBS86SP4SS
Near Bonney Lake, WA 98391
Cejay
Job Details:
04/08/2024
"Installed previously ordered FR element, cycle tested element to verify repair, all checks good. Collected payment via card."
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WF42H5000AW/A2 11
Near Graham, WA 98338
Cameron M.
Job Details:
04/08/2024
"Customer concern is that washer produces noise during spin cycle. Checked stored errors via service mode none. Cycle tested unit. Found excess tub play, causing unit to produce knocking noise during spin cycle. Customer declined repair without estimate. Due to visible damage. Collected 129+tax via card payment."
We serviced a
WHIRLPOOL RANGE
Model WFE320M0ES1
Near Spanaway, WA 98387
Cameron M.
Job Details:
04/08/2024
Installed previously ordered parts. Cycle tested unit. All checks good.
We serviced a
SPEED QUEEN DRYER-ELECTRIC
Model ADG4BRGS115TW01
Near McKinney, TX 75072
Patrick
Job Details:
04/05/2024
Replaced rollers and idler. Unit checks good.
We serviced a
SAMSUNG DISHWASHER
Model DW80R2031US/AA
Near Dallas, TX 75218
Lane
Job Details:
04/05/2024
Customer stated dishwasher will drain if cycle is canceled but leaves water in wash tub after cycle is complete. Drain pump motor has no obstruction. Drain hoses are clear and ran correctly. Possible filll valve leaking internally. Dishwasher was not mounted correctly upon arrival. Having customer do test to determine if valve is leaking.
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB865GW0
Near Dallas, TX 75218
Lane
Job Details:
04/05/2024
Customer stated washer wouldn't respond and flashed a indication light. Performed diagnostics found fault code for lid lock. Replaced lock assembly and performed multiple function tests. All functions checked good at time of service. ; used 1 W10810403 (LID LOCK ASSY) from stock
We serviced a
GE WASHER-TOPLOAD
Model PTW600BSR0WS
Near Saint Paul, TX 75098
John
Job Details:
04/05/2024
Customer concern is washer will not start and no buttons working. Found control lock engaged and firmware update needed. Removed control lock and updated firmware. All checks good.
We serviced a
FRIGIDAIRE DISHWASHER
Model FFCD2413US5A
Near Plano, TX 75074
John
Job Details:
04/05/2024
Installed new wash motor. All checks good.
We serviced a
LG DRYER-ELECTRIC
Model DLE5977W
Near Dallas, TX 75287
John
Job Details:
04/05/2024
Installed new heater. All checks good.
We serviced a
FRIGIDAIRE DISHWASHER
Model FFID2426TS4A
Near Irving, TX 75038
John
Job Details:
04/05/2024
Customer concern is DW will not drain. Found clogged air gap causing issue. Cleared air gap and tested. All checks good.
We serviced a
LG WASHER-FRONTLOAD
Model WM3600HVA
Near Lakewood, WA 98499
Cejay
Job Details:
04/05/2024
"Installed previously ordered dispenser assembly, preformed service diagnostic cycle for leaks and to verify repair, all checks good."
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model GEW9250PW1
Near Spanaway, WA 98387
Cameron M.
Job Details:
04/05/2024
Installed previously ordered parts. Cycle tested unit. All checks good
We serviced a
FRIGIDAIRE DISHWASHER
Model FFID2426TS3A
Near Tacoma, WA 98406
Cameron M.
Job Details:
04/05/2024
Installed previously ordered wash motor. Cycle tested unit. Found unit produces slow drain result. Pulled drain hose found large volume of glass in drain hose causing slow drain. Cleared debris all checks good
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRFS2853AF1
Near Garland, TX 75042
Patrick
Job Details:
04/04/2024
Replaced heater. Unit checks good.
We serviced a
LG DRYER-ELECTRIC
Model DLEX4500B
Near Forney, TX 75126
Patrick
Job Details:
04/04/2024
"Custody concern, unit displays np and stops working during use. Confirmed np. Good 250vac to terminal. Found burn marks on plug indicative of loose contact in outlet. Customer must replace outlet."
We serviced a
KENMORE WASHER-FRONTLOAD
Model 79631552610
Near Garland, TX 75040
Lane
Job Details:
04/04/2024
Installed orderd parts. Performed full function test with load. All functions checked good at time of service.
We serviced a
GE WASHER-FRONTLOAD
Model GFW650SSN2WW
Near Puyallup, WA 98371
Cejay
Job Details:
04/04/2024
"Installed previously ordered main control, cycle tested unit to verify repair, all checks good."
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model WED92HEFW0
Near Puyallup, WA 98375
Cejay
Job Details:
04/04/2024
"Installed previously ordered drum seal, cycle tested unit to verify repair, all checks good."
We serviced a
GE DISHWASHER
Model GDF550PGR3BB
Near Eatonville, WA 98328
Cameron M.
Job Details:
04/04/2024
"Customer concern is that dishwasher starts cycle runs 10-15 minutes then produces error. Cycle tested unit via Newfi device. Found faild to fill errors. Found failed to drain errors. Cycle tested unit 3x unit produced ftd error as customer described. Found debris buildup in pressure switch, causing unit to not recognize water level in tub. Cleared debris. Cycle tested unit 5x all checks good."
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW5057LW0
Near Mesquite, TX 75150
Patrick
Job Details:
04/03/2024
"Replaced drain pump. Tested unit. Good drain, good fill, all checks good."