We serviced a
JENN-AIR RANGE
Model JDS9865BDP
Near Graham, WA 98338
Cameron M.
Job Details:
01/03/2024
"Customer concern is that washer oven does not heat beyond 150. Preformed visual inspection of element found visible short of element, causing unit to not heat. Needs new element follow up visit scheduled for 1/12 8-12; ordrng 1 WPW10310274 (ELMNT-BAKE)"
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE45T3400V/A3
Near Graham, WA 98338
Cameron M.
Job Details:
01/03/2024
"Customer concern is that dryer does not heat. Preformed airflow test, failed (red).found open element, causing unit to not heat. Needs new element. Installed new element. Cleaned and vacuumed inside of unit. Cleaned and calibrated moisture sensor. Cycle tested unit. All checks good. Advised customer cannot use unit until venting is cleaned. ; used 1 DC97-14486A (ELEMENT ASSEMBLY) from stock"
We serviced a
KENMORE WASHER-TOPLOAD
Model ="11023102311"
Near Allen, TX 75002
John
Job Details:
01/03/2024
"Customer concern is washer is making a clicking noise. Found cam has failed and is stripped and belt is frayed. Replaced cam and belt from truck stick. All checks good.; used 1 W10721967 (CAM), and 1 WPW10006384 (BELT) from stock"
We serviced a
GE DISHWASHER
Model GDT630PYR6FS
Near Dallas, TX 75287
John
Job Details:
01/03/2024
"Came to install new sump and motor. Upon DW removal, found all level legs screwed all the way up against frame and motor and pump assy resting on floor. Appears as if unit was shoved into place and entire sump assy was dragging on ground and sump assy was forced toward the front of machine and is not centered. Found as follows: mounting tabs on drain pump, turbidity sensor, and pressure sensor are stressed beyond limits and will not seal to new sump. Heater posts are bent beneath tub and nuts are loose and stripped causing heater to not seal to tub. Sump latches are bent beyond limits and will not suck down sump assy in order to seal against bottom of tub. Needs new turbidity sensor, drain pump, pressure sensor, sumo latches, heater, and nuts. Left power off to DW.; ordrng 1 WD21X29818 (Turbidity sensor) and 1 WD19X25461 (Drain pump) and 1 WD21X25468 (Pressure sensor) and 3 WD01X28338 (Sump latch)s and 1 WD05X30298 (Heating element) and 1 WD01X10070 (Heater nuts)"
We serviced a
MAYTAG RANGE
Model MER5755QAW
Near Lewisville, TX 75067
John
Job Details:
01/03/2024
Customer concern is oven will not properly regulate temp after precious company replaced control and bake element. Found hinge release tab on right side was not properly reset when door was Re-installed causing it to bend hinge so that door does not fully close on right side and is allowing heat to escape. Needs new hinges.; ordrng 2 74010546 (Hinge)s
We serviced a
WHIRLPOOL WALL OVEN
Model WOC54EC0HS01
Near Wylie, TX 75098
John
Job Details:
01/03/2024
"Customer concern is wall oven shuts off randomly whether in use or not. Found F6 E4 error for Com loss between control amd UI. Per tech data, must replace control and console.; ordrng 1 W11261167 (Control board) and 1 W11297726 (Console)"
We serviced a
KENMORE DISHWASHER
Model 66513863K601
Near Dallas, TX 75252
John
Job Details:
01/03/2024
"Customer concern is DW filling while not in use. Found inlet valve to be not fully closing causing leak. Found supply line severly crimped almost closed, fitting on inlet is pile doped Iin place so that it wont seal to new valve, and service valve is corroded and unable to be closed. Advised Customer that a plumber will be needed to replace service valve and supply hose before repair can be completed.; ordrng 1 WPW10158389 (Inlet valve)"
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WF45H6300AW/A2
Near Spanaway, WA 98387
Cameron M.
Job Details:
01/02/2024
"Customer concern is that washer does not rise well. Found 5c drain error,de(door error)x5, via service mode. Pulled unit from cavity. Found drain hose in stand pipe to far, causing siphoning and slow drain. Corrected drain hose and secured in place. Cycle tested unit 5x. All checks good. Advised customer on regular cleaning intervals for optimal performance. Advised customer on using high quality detergent and proper volume of detergent for best performance. Collected 129+tax via"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28JBEDBSG/AA. 15
Near Dallas, TX 75227
Patrick
Job Details:
01/02/2024
Replaced im and auger assy. All checks good.
We serviced a
AMANA RANGE
Model AER6303MFS3
Near Coppell, TX 75019
Lane
Job Details:
01/02/2024
Customer stated oven will not exceed 280 on preheat. Performed diagnostics foumd faulty oven control and sensor. All other functions checked good at time of service. ; ordrng 1 W11536794 (Control black) and 1 WPW10181986 (Sensor)
We serviced a
WHIRLPOOL RANGE
Model WFC150MLAW0
Near Irving, TX 75062
Lane
Job Details:
01/02/2024
Customer stated oven doesn't cook correctly. Performed diagnostics found no stored fault codes. Performed function test foumd both bake and broil working. Checked calibration set to 350. Recalibrated oven +10. All functions checked good at time of service.
We serviced a
FRIGIDAIRE DISHWASHER
Model FFID2426TS4A
Near Irving, TX 75062
Lane
Job Details:
01/02/2024
Customer stated dishwasher leaks excessively when running. Performed diagnostics found rodent chewed away water supply hose coming from fill valve.
We serviced a
KITCHENAID DISHWASHER
Model KUDP02CRWH2
Near Dallas, TX 75228
Patrick
Job Details:
01/02/2024
"Customer concern, unit not filling. Found inlet valve barely trickling. Replaced from truck stock. Tested unit. All checks good. ; used 1 WPW10158389 (Inlet valve) from stock"
We serviced a
FRIGIDAIRE RANGE
Model PLEFZ398ECC
Near Garland, TX 75044
John
Job Details:
01/02/2024
"Installed new lett side controls. Cycle tested all burners. Boiled 2 pots of water on RR and LF elements. Once water on LR element begins to boil and element is turned down to simmer, element shuts off completely. Per service flash CK0803 must install seal service kit and new LCD lens covers.; ordrng 1 5304474437KIT (Seal kit) and 4 316448000 (LCD lens cover)s, states that autho needed"
We serviced a
KENMORE WASHER-FRONTLOAD
Model ="79641262610"
Near Garland, TX 75044
John
Job Details:
01/02/2024
Installed new drain pump and dispenser drawer provided by Sears. All checks good.
We serviced a
KENMORE WASHER-TOPLOAD
Model ="11026132410"
Near Richardson, TX 75082
John
Job Details:
01/02/2024
Customer concern is occasionally washer gives F6 E2 error and then recently stopped powering on all together. Confirmed 120vac to control board but no voltage to UI. Must replace control board and console/UI board.; ordrng 1 W10812699 (Control board) and 1 W11248038 (Console Complete)
We serviced a
GE RANGE
Model JGB700SEJ1SS
Near Spanaway, WA 98387
Cejay
Job Details:
01/02/2024
"Installed previously ordered harness, ignitors and spark module. Verified all burners are operating as designed. All checks good."
We serviced a
SAMSUNG RANGE
Model NE63B8211SS/AA 01
Near Edgewood, WA 98372
Cejay
Job Details:
01/02/2024
"Customer concern is that oven is not maintaining temperatures. Has had main PCB and temperature sensor replaced. Bake element tests good for continuity, 19.k ohms. Temperature sensor ohms in range at 1.096k ohms. No physical signs of damage to wire harness of relay board. Confirmed operation of broil element, confirmed operation of bake element, preformed temperature checks unit reached 350F? but after reaching temper relays never came back on, failed relay board. Advised parts show out of stock and may take time to recive.; ordrng 1 DG92-01207J (ASSY PCB MAIN)"
We serviced a
LG RANGE
Model LRE304538T/01
Near Puyallup, WA 98374
Cejay
Job Details:
01/02/2024
"Installed previously ordered RF element, cycle tested element all checks good."
We serviced a
KENMORE DISHWASHER
Model 66512793K311
Near Garland, TX 75043
Patrick
Job Details:
01/02/2024
"Replaced upper rack rails, replaced lower rack rollers. Cleared ball bearings from sump and drain system. Tested unit. All checks good."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ01
Near Rockwall, TX 75032
Patrick
Job Details:
01/02/2024
"Replaced filter head assy, drip ceased. Only received 1 led module, tested new, no joy. Need 2 additional led modules. Left middle speed by ast at customer home. ; ordrng 2 W11683243 (Led module)s"
We serviced a
SAMSUNG WASHER-TOPLOAD
Model WA50R5200AW/US 03
Near Plano, TX 75075
John
Job Details:
01/02/2024
Installed new suspension rods and inlet valve. Found new inlet valve leaks between the third solenoid and valve body. Must re-order OEM inlet valve.; ordrng 1 DC97-15459H (Inlet valve assy)
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB700VQ0
Near Tacoma, WA 98408
Cameron M.
Job Details:
01/02/2024
"Customer concern is that washer produces running motor noise at end of cycle requiring unit to be unplugged. Cycle tested unit 5x, via rinse and spin no defect found. Cycle tested unit via drain and spin 5x ,no defect found. Advised customer on regular cleaning intervals advised customer on using high quality detergent and proper volume of detergent. Advised customer to monitor and call if issues persist. Collected 129+TaX via card payment"
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWC565FW2
Near Tacoma, WA 98408
Cameron M.
Job Details:
01/02/2024
"Installed previously ordered gearcase, hub,belt, pully. Cycle tested unit. All checks good."
We serviced a
WHIRLPOOL COOKTOP
Model KGCC506RBL04
Near Irving, TX 75063
John
Job Details:
01/02/2024
"Customer concern is cooktop will not light. Upon arrival unit unplugged and breaker tripped. Reset breaker and plugged in cooktop. Found when knob turned to ignite burner a visible spark/short appears at switch on valve and then pops and tripps breaker. Found FL burner screws are siezed in place and will have to be drilled. Must replace LF burner base, screws, spark module, and spark harness. Advis3d customer not to use cooktop untill repair can be completed. Left unit unplugged and gas turned off.; ordrng 1 WPW10128445 (LF burner base and igniter) and 1 WPW10110491 (Spark module) and 1 WP4456905 (Spark harness) and 4 WP3368921 (Screw)s"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAHZ0
Near Buckley, WA 98321
Cejay
Job Details:
01/02/2024
"Customer concern is that dishwasher has poor wash performance and is not draining. Pulled error codes, F2E1,F6E4. Confimed operation of float switch, preformed diagnostics cycle, errors did not return. Found drain pump producing grinding noise but dose complete drain. Installed SQT provided drain motor, cycle tested dishwasher, noise eliminated all checks good. Advised customer on using high quality detergent and rinse aid and running regular cleaning cycles. Returning two SQT provided parts."
We serviced a
GE DISHWASHER
Model PDT755SYR4FS
Near Plano, TX 75025
Chad A.
Job Details:
01/02/2024
Replaced heater and tco harness. Cycled heater test in smart hq and all checked good. No other failures detected.
We serviced a
GE WALL OVEN
Model JTS3000SN2SS
Near Plano, TX 75025
Chad A.
Job Details:
01/02/2024
Replaced UI LCD control panel. Display bright and readable. Tested bake and broil. Both functioning properly.
We serviced a
GE DISHWASHER
Model GDP665SYN8FS
Near Frisco, TX 75034
Chad A.
Job Details:
01/02/2024
Replaced inverter and harness as well as wash motor. Cycled to test and inverter cycling properly and water level good. Cleared error codes and cycled diagnostic. No other failures found.
We serviced a
AMANA WASHER-TOPLOAD
Model NTW4516FW
Near Denton, TX 76208
Chad A.
Job Details:
01/02/2024
Replaced water valve assembly and cycled to test. Good water flow from hot and cold valves. No other failures detected at time of repair.
We serviced a
WHIRLPOOL WASHER-FRONTLOAD
Model WFW5620HW0
Near Tacoma, WA 98409
Cameron M.
Job Details:
01/02/2024
"Customer concern is that washer produces oe error and bangs during spin. Attempted to service mode unit, found unit looses power and fails service mode. Found main control and ui failing to send and receive signal voltage, causing unit to loose power and not function. Cycle tested unit empty, unit n completed cycle without issue. Cycle tested unit after 3 attempts of unit loosing power load of towels completed without drive component defect. Needs new main control and ui. Requires auth. Advised customer unit will need to be made accessible for repair. REQUIRES AUTH ; ordrng 1 W11322903 (cntrl-elec) and 1 W11319991 (CNTRL-ELEC)"
We serviced a
GE LAUNDRY CENTER
Model GUD27ESSM1WW
Near Eatonville, WA 98328
Cameron M.
Job Details:
01/02/2024
"Customer concern is that washer goes Out of balance. Unit in communal laundry room. contacted ge via phone to verify warranty coverage, spoke to Jason and was advised unit still covered as communal laundry is not considered commercial usage. Unit full of laundry at time of service. Removed laundry from unit and placed in dryer of unit next to suspect unit. Preformed inspection of unit. Found unlevel causing out of balance condition. Leveled unit Cycle tested unit empty x3. Unit completed cycle without issue. Placed laundry back in unit tested unit again x3 ,unit completed cycle. found no other mechanical defects at time of arrival."
We serviced a
WHIRLPOOL DISHWASHER
Model DU850SWPB3
Near Eatonville, WA 98328
Cameron M.
Job Details:
01/02/2024
Installed previously ordered timer. Cycle tested unit. All checks good.
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WA54R7600AC/US. 01
Near Irving, TX 75060
Lane
Job Details:
01/02/2024
Customer stated washer gets out of balance on every load. Performed diagnostics found wash tub is contacting top of washer. Suspension rods are the wrong length for this model. Washer will need to be installed for proper testing after repair. ; ordrng 4 DC97-16350V (Suspension rods)s
We serviced a
ELECTROLUX DRYER-ELECTRIC
Model EFME617SIW0
Near Irving, TX 75063
Lane
Job Details:
01/02/2024
Customer stated dryer makes abnormal noise. Performed diagnostics found blower wheel and housing needed to be cleaned. Cleaned housing and blower. All functions checked good at time of service.
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW8000BW0
Near Dallas, TX 75229
John
Job Details:
01/02/2024
"Customer concern is washer leaking. Ran diagnostics, no leaks found. Found dryer lint catcher has warped from heat and is leaking down wall to floor. Aslo found no worm clamp on connection to lint filter and loose connection between rigid and flex hose causing moisture to escape from hose. Advised Customer that lint filter will need to be changed as will as vent hose. All other checks good."
We serviced a
SPEED QUEEN DRYER-ELECTRIC
Model ADE4BRGS171TW01
Near Dallas, TX 75230
Lane
Job Details:
01/02/2024
Installed new heating element. Performed multiple function tests after repair. All functions checked good at time of service.
We serviced a
OTHER RANGE
Model DF484C0
Near Dallas, TX 75248
Lane
Job Details:
01/02/2024
Customer stated both front burners continuously click on low simmer function and rear left simmer doesn't function at all. Performed diagnostics found electrodes need replacing. Left front burner assembly needs to be replaced due to broken screw. Left front simmer orifice clogged preventing proper gas flow Ignition modules are faulty causing intermittent ignition issues with all burners. ; O-emld tckt
We serviced a
GE WALL OVEN
Model JTS3000SN2SS
Near Dallas, TX 75287
John
Job Details:
01/02/2024
"Customer concern is wall oven racks will not slide in or out with out scrapping sides of inner cavity. Found unit manufactured out of square, causing racks to binde in back of unit, doormto not close straight, and door seal to tear. Also found racks chipping ceramic coating in various placed. Parts required are not serviceable."
We serviced a
GE DISHWASHER
Model GDT655SMJ0ES
Near Tacoma, WA 98443
Cameron M.
Job Details:
12/27/2023
Installed previously ordered parts. Cycle tested unit. All checks good
We serviced a
MAYTAG DISHWASHER
Model MDB9979SKZ0
Near Tacoma, WA 98444
Cameron M.
Job Details:
12/27/2023
Installed previously ordered element. Cycle tested unit. All checks good left failed part with customer as part caused leak
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model WED8000DW4
Near Tacoma, WA 98444
Cameron M.
Job Details:
12/27/2023
"Customer concern is that dryer produces noise during operation. Inspected drive system components, found damaged idler pully causing noise during operation. Needs new idler pully. Installed new idler pully. Cleaned and vacuumed inside of unit. Cleaned and calibrated moisture sensor. Cycle tested unit. All checks good. Preformed airflow test, failed (yellow). Advised customer dryer vent needs to be cleaned. ; used 1 W10837240 (BRACKET) from stock"
We serviced a
LG WASHER-FRONTLOAD
Model WM37OOHVA
Near Fircrest, WA 98466
Cameron M.
Job Details:
12/27/2023
Installed previously ordered door boot. Cycle tested unit. All checks good. Collected remainder balance via check payment.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADW9
Near DuPont, WA 98327
Cejay
Job Details:
12/27/2023
"Installed previously ordered main control board and sump and motor, preformed service diagnostic cycle for leaks and to verify repair. All checks good."
We serviced a
SAMSUNG DISHWASHER
Model DW80M2020US/AA 00
Near Sumner, WA 98390
Cejay
Job Details:
12/27/2023
"Prior to arrival, Customer did have shut off valve installed for dishwasher. Installed previously water valve, cycle tested unit it for leaks and to verify repair. All checks good."
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model WED5100HW1
Near Spanaway, WA 98387
Cejay
Job Details:
12/27/2023
"Installed previously ordered terminal block kit, cycle tested dryer all checks good."
We serviced a
GE WASHER-TOPLOAD
Model GTW335ASN2WW
Near Lewisville, TX 75067
Chad A.
Job Details:
12/27/2023
Customer stated washer not going through cycles properly. Cycled to test and found drain hose inserted into wall drain all the way to trap. Raised and secured drain hose. Leveled machine and tested spin loaded with clothes. No other failures detected and all working properly.
We serviced a
GE DISHWASHER
Model GDT630PYR7FS
Near Plano, TX 75024
Chad A.
Job Details:
12/27/2023
Customer stated dishwasher not drying dishes. Performed diagnostics and found heater disconnect wire harness. Secured heater connection and tested good. No other failures detected.
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model LEB6400LW0
Near Irving, TX 75062
Lane
Job Details:
12/27/2023
Installed new timer and door switch. Performed full function test after repair. Timer is advancing and automatically turning off dryer.
We serviced a
SAMSUNG REFRIGERATOR
Model RS27T5200SR/AA. 02
Near Dallas, TX 75229
Lane
Job Details:
12/27/2023
Installed dispenser assembly and performed multiple function tests after repair. All functions checked good at time of service.
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE50R5200W/A3
Near Garland, TX 75043
Lane
Job Details:
12/27/2023
Customer stated dryer won't stop running. Performed diagnostics found motor relay stuck. Unstuck relay and performed multiple function tests. All functions checked good at time of service.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT710PAHB1
Near Plano, TX 75075
Lane
Job Details:
12/27/2023
Installed new sump assembly and performed full function and leak test after repair. All functions checked good at time of service.
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV328AEW/XAA
Near Spanaway, WA 98387
Cameron M.
Job Details:
12/26/2023
"Customer concern is that dryer does not heat. Preformed airflow test, failed (red). Tested continuity of heating components.,failed found open thermal cutoff, causing unit to not heat. Also found seized idler pully, causing noise during operation. Needs new thermal cutoff, high limit, thermistor and idler pully. Installed new thermistor, thermal cutoff, high limit and idler pully. Cycle tested unit. All checks good. ; used 1 DC93-00634A (IDLER ASSEMBLY), 1 DC47-00018A (OPERATING THERMOSTAT), 1 DC96-00887C (THERMAL CUT-OFF), and 1 DC32-00007A (THERMISTOR) from stock"
We serviced a
KITCHENAID DISHWASHER
Model KUDS301VSS3
Near University Place, WA 98466
Cameron M.
Job Details:
12/26/2023
Installed previously ordered manifold. Cycle tested unit. All checks good collected remainder balance via card payment
We serviced a
MAYTAG DISHWASHER
Model MDB9959SKZ0
Near Enumclaw, WA 98022
Cameron M.
Job Details:
12/26/2023
"Customer concern is that dishwasher produces f8e4 error. Arrived to unit actively producing f8e4 error, inspected leak tray. Found water in try causing unit to produce error. Found unit unlevel, causing unit to leak from front triggering leak error. Leveled unit Cycle tested unit. All checks good. Advised customer on regular cleaning intervals. Advised customer on using high quality detergent."
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW5105HW1
Near Spanaway, WA 98387
Cameron M.
Job Details:
12/26/2023
"Customer concern is that washer produces noise during operation Cycle tested unit. Verified customer concern. Found debris under unit, causing belt shroud to make contact with pully. Needs new cam and belt . Installed new cam and belt Cycle tested unit. All checks good. Advised customer on regular cleaning intervals. Advised customer on proper loading practices ; used 1 W11239857 (BELT), and 1 W10721967 (CAM) from stock"
We serviced a
FRIGIDAIRE DISHWASHER
Model FFID2426TD2A
Near Lakewood, WA 98499
Cejay
Job Details:
12/26/2023
"Customer concern is that dishwasher has three flashing lights. Found failed UI board causing unit not to operate. Installed new UI board. Cycle tested unit to verify repair, all checks good."
We serviced a
GE WASHER-FRONTLOAD
Model PFWS4600L0WW
Near Eatonville, WA 98328
Cejay
Job Details:
12/26/2023
"Customer concern is that washer is filling with water even when unit is unplugged. Confirmed I let valve is stuck open. Needs new inlet valve. Installed new inlet valve, cycle tested unit it for leaks and to verify repair, all checks good."
We serviced a
WHIRLPOOL WASHER-FRONTLOAD
Model WFW6605MC0
Near Frisco, TX 75034
Chad A.
Job Details:
12/26/2023
Replaced door bellow due to tear in front bottom of seal. Cycled to test and found no leaks or any other failures. All functioning properly.
We serviced a
KENMORE WASHER-TOPLOAD
Model 11025132411
Near Plano, TX 75024
Lane
Job Details:
12/26/2023
I stalled ordered parts and calibrated washer. Performed full function test after repair. All functions checked good at time of service.
We serviced a
GE WASHER-FRONTLOAD
Model GFW550SSN0WW
Near Dallas, TX 75205
Lane
Job Details:
12/26/2023
Replaced ordered parts and performed multiple function and leak tests after. All functions checked good at time of service.
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW8127LW0
Near Carrollton, TX 75007
Lane
Job Details:
12/26/2023
Installed rotor and performed full function test. All functions checked good at time of service.
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV42H5200EW/A3
Near Plano, TX 75094
Lane
Job Details:
12/26/2023
"Customer stated dryer runs but doesn't heat. Preformed diagnostics found faulty heating element and rear drum roller. Replaced parts and performed full function test. All functions checked good at time of service. ; used 1 Dc47-00019a (Heating element), and 1 DC97-16782A (Drum roller) from stock"
We serviced a
FRIGIDAIRE DISHWASHER
Model LFID2426TF1A
Near Tacoma, WA 98405
Cejay
Job Details:
12/22/2023
"Installed previously ordered latch assembly, cycle tested unit to verify repair, all checks good.; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #)"
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB855DC3
Near Eatonville, WA 98328
Cameron M.
Job Details:
12/22/2023
"Installed previously ordered gearcase, slider, screw and washplate. Cycle tested unit. All checks good"
We serviced a
LG RANGE
Model LREL6323S/01
Near Puyallup, WA 98375
Cejay
Job Details:
12/22/2023
"Installed previously ordered bake element, cycle tested unit to verify operation of bake element, all checks good."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE50M7450W/A3
Near Tacoma, WA 98445
Cameron M.
Job Details:
12/21/2023
"Customer concern is that dryer produces squealing noise during operation. Inspected inside unit. Found failed rear right roller and front left roller, causing squealing noise during operation. Needs new rollers. Installed new rollers. Cleaned and vacuumed inside of unit. Cleaned and calibrated moisture sensor. Cycle tested unit all checks good. ; used 2 DC97-16782A (DRUM ROLLER) from stock"
We serviced a
GE DISHWASHER
Model CDT805M5N3S5
Near Lakewood, WA 98499
Cameron M.
Job Details:
12/21/2023
Installed previously ordered harness and diverter disk. Cycle tested unit all checks good. Collected remainder balance via card payment.
We serviced a
LG DISHWASHER
Model LDF5545SS
Near Spanaway, WA 98387
Cameron M.
Job Details:
12/21/2023
Installed previously ordered pcb kit and console. Cycle tested unit. All checks good
We serviced a
WHIRLPOOL COOKTOP
Model W3CG3014XB02
Near Wylie, TX 75098
Chad A.
Job Details:
12/21/2023
Installed spark module and burner switch harness. Cycled all burners several times and had no other failures.
We serviced a
GE WASHER-FRONTLOAD
Model GFW850SPN2RS
Near Plano, TX 75075
Chad A.
Job Details:
12/21/2023
Customer stated pump filter cover will not stay in place replaced cover due to broken upper clip. No other failures detected at time of service.
We serviced a
GE DISHWASHER
Model GLD4408R00BB
Near Dallas, TX 75287
Lane
Job Details:
12/21/2023
Customer stated dishwasher is still leaking. Performed diagnostics found air gap leaking causing water to run down drain hose and drip under sink. Advised customer to have plumber service air gap.
We serviced a
MAYTAG WALL OVEN
Model CWE5800ACE
Near Richardson, TX 75081
Lane
Job Details:
12/21/2023
Customer stated upper oven stopped working. Performed diagnostics found thermal limiter good. Relay controller failed causing issue Parts have been discontinued.
We serviced a
SPEED QUEEN WASHER-FRONTLOAD
Model AFNE9BSP113TW01
Near Dallas, TX 75218
Lane
Job Details:
12/21/2023
Customer stated washer was leaking a large amount of water from underneath machine. Performed diagnostics checked all hoses water connections and drainage system. No leaks at time of service. Customer stated water level wasn't high inside washer. Unable to recreate problem.
We serviced a
GE DISHWASHER
Model GDT635HSJ0SS
Near Irving, TX 75039
Lane
Job Details:
12/21/2023
Customer stated dishwasher leaked out of left side of door. Another company came out and made some adjustments . Customer stated after repair right side of dishwasher started leaking. Performed diagnostics ran dishwasher for 20min with no leaks. Possible object blocking door.
We serviced a
KENMORE WASHER-TOPLOAD
Model 110.28102310
Near Garland, TX 75043
Patrick
Job Details:
12/21/2023
"Customer concern, unit leaking during use. Confirmed. Found fabric softener dispenser overflowing. Cleared clog. Tested unit. All checks good."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB765FW3
Near Rockwall, TX 75087
Patrick
Job Details:
12/21/2023
"Replaced gear case, upon disassembly, found damaged slider. Replaced from truck stock. Tested unit. All checks good. ; used 1 W10734521 (Slider) from stock"
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW4955HW2
Near Wylie, TX 75098
Patrick
Job Details:
12/21/2023
Replaced drive block. Calibrated unit. Ran spin only.
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVW7232HW0
Near Puyallup, WA 98375
Cameron M.
Job Details:
12/20/2023
Installed previously ordered parts. Cycle tested unit. All checks good.
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV40J3000EW/A2 02
Near Spanaway, WA 98387
Cameron M.
Job Details:
12/20/2023
"Customer concern is that dryer produces intermittent squealing noise during operation. Inspected unit, found seized rear right and front left drum rollers, causing noise during operation. Found seized idler pully causing noise during operation. Needs new idler pully and drum rollers. Installed new rollers and idler. Cleaned and vacuumed inside of unit. Cleaned and calibrated moisture sensor. Cycle tested unit. All checks good. Preformed airflow test,failed (red). Advised customer dryer vent needs to be cleaned asap before use resumes to prevent damage to heating components. Collected payment via ; used 1 DC93-00634A (IDLER ASSEMBLY), and 2 DC97-16782A (DRUM ROLLER) from stock"
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWC200BW0
Near Spanaway, WA 98387
Cameron M.
Job Details:
12/20/2023
Installed previously ordered lid lock and suspension rods. Cycle tested unit. All checks good.
We serviced a
LG REFRIGERATOR
Model LRSC26923TT
Near Graham, WA 98338
Cejay
Job Details:
12/20/2023
"Customer concern is that refrigerator is not dispensing water or making ice. Found failed inlet vale causing unit not to dispense water through secondary valves. Needs new inlet valve assembly. Installed new valve, confirmed operation of dispenser, advised customer icemaker may take 24 hours to produce ice. Collected payment via card"
We serviced a
KENMORE REFRIGERATOR
Model 10651132213
Near Puyallup, WA 98371
Cejay
Job Details:
12/20/2023
"Installed previously ordered evaporator fan motor, wire harness and ice maker, advised custo,er unit make take up to 24 hours to get to temperature, also Advised ice maker will not freeze ice until unit is to temperature."
We serviced a
GE COOKTOP
Model JP3030SJ4SS
Near The Colony, TX 75056
Chad A.
Job Details:
12/20/2023
Installed cooktop burner switch assembly recall kit. All functioning properly and no failures detected.
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW5000DW3
Near The Colony, TX 75056
Chad A.
Job Details:
12/20/2023
"Replaced inner basket with hub and washplate. Cycled to test. Water fill,agitate,and spin all working properly."
We serviced a
SAMSUNG REFRIGERATOR
Model RF25HMEDBSR/AA 15
Near Frisco, TX 75033
Chad A.
Job Details:
12/20/2023
"Customer stated ice maker leaking water. Installed ice maker kit,water filter assembly and ice bucket due to being cracked. Cycled icemaker and water fill checked good. No other failures found at time of service."
We serviced a
GE DRYER-ELECTRIC
Model GTD42EASJ2WW
Near Garland, TX 75044
John
Job Details:
12/20/2023
"Customer concern is dryer vent hose needs to be cleaned and unit taking long time to dry. Found vent hose kinked at connection to home ventilation. Removed hose and cleaned. Reinstalled and repaired kinked portion of hose. Vent check passes green. Temp check passes inside if drum and at exhaust. All checks good, unit operating as designed."
We serviced a
GE DISHWASHER
Model GDT535PSR3SS
Near The Colony, TX 75056
Lane
Job Details:
12/20/2023
Customer stated dishwasher stopped washing well and detergent doesn't always desolve. Performed diagnostics found filter completely clogged. Customer was unaware of any required maintenance. Performed full function test after repair. All functions checked good at time of service.
We serviced a
SAMSUNG REFRIGERATOR
Model RF28T5001SR/AA
Near Dallas, TX 75228
Patrick
Job Details:
12/20/2023
Replaced fzim. All checks good.
We serviced a
GE DRYER-ELECTRIC
Model DVL223EB3WW
Near Dallas, TX 75210
Patrick
Job Details:
12/20/2023
Replaced belt. Tested unit. All checks good.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT920SADM2
Near Plano, TX 75074
Patrick
Job Details:
12/20/2023
Replaced sump assy.ran svc cycle. All checks good.
We serviced a
KITCHENAID DISHWASHER
Model KUDC10FXSS5
Near Buckley, WA 98321
Branden W.
Job Details:
12/19/2023
Installed new console and main board. Cycled through service cycle. All checks good.
We serviced a
KITCHENAID DISHWASHER
Model KDTE104ESS4
Near Bonney Lake, WA 98391
Branden W.
Job Details:
12/19/2023
Installed previously ordered pump and sump assembly. Cycle tested. All checks good. Advised dishwasher should be mounted to prevent unit from leaning forward and leaking.
We serviced a
LG DISHWASHER
Model LDF5545ST
Near Graham, WA 98338
Branden W.
Job Details:
12/19/2023
Installed previously ordered dispenser. Cycle tested through service cycle. All components operating as designed.
We serviced a
GE DISHWASHER
Model GDT670SYV0FS
Near Prosper, TX 75078
Chad A.
Job Details:
12/19/2023
Customer stated roller assembly came off rack and melted to heater. Replaced lower rack assembly. Roller assembly had been cleared and free from heater before arrival. Tank and heater clean and ready for use.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRTD2021AS0
Near Frisco, TX 75033
Chad A.
Job Details:
12/19/2023
Customer stated refrigerator not cooling. On arrival temperatures in both freezer and refrigerator sections too high. Compressor running but not cooling properly. 600a unit. Sealed system rebuild needed. No repair at this time.
We serviced a
HOTPOINT DISHWASHER
Model HDF310PGR3WW
Near Lewisville, TX 75067
Chad A.
Job Details:
12/19/2023
Replaced machine control and harness. Cycled to test and functioning properly.
We serviced a
GE DRYER-ELECTRIC
Model GTD45EASJ2WS
Near McKinney, TX 75071
Chad A.
Job Details:
12/19/2023
Customer stated dryer not heating. Performed voltage tests and found only 120 volts to wall outlet. L2 has 120v to neutral and L1 has no voltage to neutral. Reset breaker but made no difference. Recommend getting electrician to resolve issue.
We serviced a
KITCHENAID COOKTOP
Model KECS100SBC4
Near Dallas, TX 75229
John
Job Details:
12/19/2023
"Installed new burners, receptacles, and drip bowls. All checks good."
We serviced a
MAYTAG DRYER-ELECTRIC
Model MED7230HW2
Near Rowlett, TX 75089
Patrick
Job Details:
12/19/2023
"Customer concern, unit not heating. Confirmed. Found open element. Replaced from truck stock. Tested unit all checks good. ; used 1 WP3387747 (Element) from stock"