Service History 122 - RPS Appliance Repair

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model GEQ8811LW0

Near Puyallup, WA 98374

Branden W.

Job Details: 01/05/2022

"Customer concern is that dryer does not heat. Found open thermal cutoff causing unit to not heat. Replaced thermal cut off and high limit thermostat. Performed airflow test. Test failed (red). Pulled dryer out so duct is not crushed, cleaned exterior flap. Performed airflow test again. Test passed (yellow). Advised to replace and position duct so it is straight from dryer to wall and not crushed. Vacuumed inside of dryer. ; used 1 279769 (THERMAL CUTOFF) from stock"

We serviced a

MAYTAG WASHER-TOPLOAD

Model MTW6600TQ0

Near Gig Harbor, WA 98332

Cameron M.

Job Details: 01/04/2022

Installed previously ordered drain pump and bearing asm. Cycle tested unit all checks good

We serviced a

GE WASHER-FRONTLOAD

Model GFW550SSN0WW

Near Garland, TX 75043

Jacob P.

Job Details: 01/04/2022

"Customer concern of multiple buttons unresponsive on console. Found ui board unmounted causing buttons to be unresponsive. Secured ui board in console. Test cycled, all checks ok."

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV419AEW/XAA

Near Grand Prairie, TX 75051

Jacob P.

Job Details: 01/04/2022

"Customer concern of unit not heating. Found open heating element causing no heat and seized idler pulley. Replaced heating element and idler pulley. Test cycled, all checks ok. ; used 1 DC93-00634A (IDLER ASSEMBLY), and 1 DC97-14486A (ELEMENT ASSEMBLY) from stock"

We serviced a

WHIRLPOOL DISHWASHER

Model WDF560SAFB2

Near Puyallup, WA 98372

Branden W.

Job Details: 01/04/2022

"Customer concern is that dishwasher does not wash. Found 120v to wash pump, no movement from pump. Needs new wash pump and grommet. Declined to repair at this time."

We serviced a

MAYTAG DISHWASHER

Model MDB7749AWM2

Near Gig Harbor, WA 98335

Cameron M.

Job Details: 01/04/2022

"Customer concern is that dishwasher does not power or start cycle. Found open thermal fuse, causing unit to not power and start cycle. Needs new thermal fuse. Installed thermal fuse, cycle tested unit 3x. All checks good ; used 1 W10258275 (BI-METAL THERMAL FUSE) from stock"

We serviced a

KENMORE WASHER-FRONTLOAD

Model 11042924200

Near Tacoma, WA 98404

Cameron M.

Job Details: 01/04/2022

"Installed sears provided main board, cycle tested unit. All checks good. Advised customer on using high quality detergent. Also advised customer on regular cleaning intervals for optimal performance."

We serviced a

LG WASHER-FRONTLOAD

Model WM3770HVA

Near Allen, TX 75002

Jacob P.

Job Details: 01/03/2022

"Installed previously ordered door lock and strike. Test cycled, all checks ok."

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DVE60M9900V/A3

Near McKinney, TX 75070

Jacob P.

Job Details: 01/03/2022

"Customer concern of unit not heating. Found open cut off causing no heat. Replaced cut off. Test cycled, unit now heats. Ran air flow test, failed. Advised customer that vent from back of dryer to outside needs to be cleaned. ; used 1 DC96-00887C (THERMAL CUT-OFF) from stock"

We serviced a

FRIGIDAIRE DISHWASHER

Model FGBD2438PF6A

Near McKinney, TX 75071

Jacob P.

Job Details: 01/03/2022

"Installed previously ordered spray arm. Test cycled, all checks ok."

We serviced a

GE DRYER-ELECTRIC

Model DCVH480EK0WW

Near Tacoma, WA 98445

Cameron M.

Job Details: 01/03/2022

"Installed previously ordered idler pulley and front right roller. Cycle tested unit, all checks good. Preformed airflow test failed (yellow ) . Advised customer dryer vent duct needs to be cleaned."

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model WED8300SW0

Near DuPont, WA 98327

Cameron M.

Job Details: 01/03/2022

"Installed previously ordered main control board. Cycle tested unit, all checks. Preformed airflow test. Failed (yellow). Advised customer dryer vent duct needs to be cleaned."

We serviced a

KENMORE WASHER-FRONTLOAD

Model 79640518900

Near Gig Harbor, WA 98335

Branden W.

Job Details: 01/03/2022

Customer concern is that washer will not power on. Has to unplug unit and replug to use it. Found failed control board failing to store energy. New control board is discontinued. Unable to repair.

We serviced a

KENMORE DRYER-ELECTRIC

Model 11065132411

Near Bonney Lake, WA 98391

Branden W.

Job Details: 01/03/2022

"Customer concern is that dryer does not operate after moving to new home. Found no voltage at outlet causing unit to not operate. Breaker not tripped. Reset breaker several times, still no power. Advised that electrician is needed."

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV42H5000EW/A3 04

Near Dallas, TX 75235

Jacob P.

Job Details: 01/03/2022

"Customer concern of unit not working. Tested voltage, 0v from L1 to L2. 120v between L1 to N and L2 to N. Advised customer electrician is needed to fix power supply to unit."

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model WED7120HW0

Near Rockwall, TX 75032

Jacob P.

Job Details: 01/03/2022

"Customer concern of no heat. Found open heating element causing no heat. Replaced heating element. Test cycled, all checks ok. ; used 1 WP3387747 (ELEMENT) from stock"

We serviced a

FRIGIDAIRE DISHWASHER

Model FFCD2413US2A

Near Dallas, TX 75216

Jacob P.

Job Details: 01/03/2022

"Customer concern of unit not draining. Found plug still installed in garbage disposal causing no drain. Removed plug. Test cycled, all checks ok."

We serviced a

MAYTAG DISHWASHER

Model MDB7749AWB2

Near Rowlett, TX 75089

Jacob P.

Job Details: 01/03/2022

"Installed previously ordered console and cap. Test cycled, all checks ok."

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWB835DW4

Near Graham, WA 98338

Cameron M.

Job Details: 01/03/2022

"Customer concern is that washer produces LF error code. Found F8e1 (long fill) present via service mode. Found sticking inlet valve, causing unit to not fill at proper rate, and produce LF error. Needs new inlet valve. Installed inlet valve, cycle tested unit. All checks good. Advised customer on using high quality detergent for best wash results. ; used 1 W11165546 (VALVE) from stock"

We serviced a

GE DISHWASHER

Model GDF640HSM2SS

Near Spanaway, WA 98387

Branden W.

Job Details: 12/31/2021

"Customer concern is that dishwasher does not operate. Console is dead. Found no response between UI and main boards. Reseated connection, reset control board. Reapplied power to dishwasher. Unit no operating properly. Test cycle in service cycle and quick cycle. All checks good at this time. If issue returns, UI board will need to be replaced."

We serviced a

KENMORE DRYER-ELECTRIC

Model 11062722100

Near Buckley, WA 98321

Branden W.

Job Details: 12/31/2021

Customer concern is that dryer takes multiple cycles to dry. Found dryer fails airflow test. Poor airflow causing dryer to take too long to dry. Found lint buildup inside of dryer lint chute causing poor airflow. Vacuumed inside of dryer. Also replaced paper venting duct with foil. Cycle tested dryer checks good. Advised duct from floor to outside needs to be cleaned asap. ; used 1 BTD48 ( 4: X 8' FLEX DUCT) from stock

We serviced a

SAMSUNG DISHWASHER

Model DW80K7050UG/AA 02

Near Sumner, WA 98391

Branden W.

Job Details: 12/31/2021

Customer concern is that dishwasher overfilled and leaked from front and produced error code. Dishwasher unmounted and unplugged prior to service. Cycle tested x5. Unable to get unit to overfill or leak. Did find dishwasher undeveloped leaning forward. This is likely cause of leak. Raised front of dishwasher 3/4 inch to level. All checks good at this time.

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWB865GW0

Near Bonney Lake, WA 98391

Branden W.

Job Details: 12/31/2021

Customer concern is that washer intermittently does not operate and lid lock flashes. Also has intermittently made noise from drive system. Found failed lid lock causing unit to not operate. Unable to verify noise. Cycle tested numerous times. Replaced lid lock. All checks good. ; used 1 W10810403 (LID LOCK ASSY) from stock

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWC415EW2

Near Enumclaw, WA 98022

Branden W.

Job Details: 12/31/2021

Customer concern is that washer is stuck draining. Found washer stuck in drain clearing mode. Reset control. Cycle tested. All checks good.

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV45K6500EV/A3 01

Near Sumner, WA 98391

Branden W.

Job Details: 12/31/2021

"Person home at time of service does not know concern with dryer. Per job creation description, dryer does not heat or takes too long to dry. Cycle tested dryer, temperatures at 180 on high heat. Performed airflow test. Failed. Removed vent from dryer,, tested again. Passed. Cleaned and calibrated moisture sensors. Advised to have dryer duct cleaned from wall to outside. Dryer operating as designed at time of service."

We serviced a

AMANA DRYER-ELECTRIC

Model n/a

Near Fircrest, WA 98466

Branden W.

Job Details: 12/30/2021

"Customer concern is that dryer does not heat. Found open heating element causing no heat. Replaced element. Cycle tested. High temp of 150 at exhaust. Good airflow. All checks good. ; used 1 279838 ( ELEMENT,HEATER) from stock"

We serviced a

GE WASHER-TOPLOAD

Model GCWN4950D0WS

Near Puyallup, WA 98375

Branden W.

Job Details: 12/30/2021

Customer concern is that washer fails to operate intermittently. Found 120vac with proper polarity supplied to washer. Unable to get unit to fail at time of service. Tested all components. All check good. Needs new main control board. Declined to repair at this time

We serviced a

SAMSUNG DISHWASHER

Model DW80K5050US/AA 03

Near Graham, WA 98338

Branden W.

Job Details: 12/29/2021

"Customer concern is that dishwasher does not drain. Dishwasher not mounted, sits below flooring, missing toe panel and not grounded prior to arrival. Found debris in drain pump causing unit to not drain. Cleaned pump. Cycle tested x3. All checks good."

We serviced a

GE WASHER-TOPLOAD

Model GTW335ASN0WW

Near Eatonville, WA 98328

Branden W.

Job Details: 12/29/2021

Installed new board and shifter. Cycle tested. All checks good

We serviced a

GE DISHWASHER

Model GDT625PSJ2SS

Near Sumner, WA 98390

Branden W.

Job Details: 12/29/2021

Customer concern is that dishwasher does not fill. Found dishwasher fails to run any components. Reset control and updated to latest firmware. Unit now functions properly. Cycle tested x5. All checks good.

We serviced a

KITCHENAID DISHWASHER

Model KUDE60FXWH2

Near Spanaway, WA 98387

Branden W.

Job Details: 12/28/2021

"Installed new sump, spray arm and motor. Cycle tested. All checks good."

We serviced a

KITCHENAID DISHWASHER

Model KDS19

Near Puyallup, WA 98373

Branden W.

Job Details: 12/28/2021

Customer concern is that dishwasher does not drain. Spray arm and filter removed prior to service. Found clogged drain hose causing no drain. Cleared hose. Cycle tested x3. All checks good.

We serviced a

LG WASHER-FRONTLOAD

Model WM8100HVA

Near Fife, WA 98424

Branden W.

Job Details: 12/23/2021

Customer concern is that washer shakes too much. Items on top of washer will fall off. Found no mechanical failures. Cycle tested with load of towels on extra high spin speed. Found unit slightly out of level. Leveled washer. Vibration is within normal parameters.

We serviced a

FRIGIDAIRE DISHWASHER

Model FPID2495QF0A

Near Coppell, TX 75019

Jacob P.

Job Details: 12/23/2021

"Installed previously ordered pressure switch. Test cycled,all checks ok."

We serviced a

GE WALL OVEN

Model JTP56S0D1SS

Near Heath, TX 75032

Jacob P.

Job Details: 12/23/2021

"Installed previously ordered convection motor and element. Test cycled, all checks ok."

We serviced a

MAYTAG DRYER-ELECTRIC

Model MDE6460AYW

Near Irving, TX 75062

Jacob P.

Job Details: 12/23/2021

"Installed previously ordered idler, rollers, belt and screws. Test cycled, all checks ok."

We serviced a

GE DISHWASHER

Model GDT720SSF4SS

Near Frisco, TX 75034

Jacob P.

Job Details: 12/23/2021

"Installed previously ordered feed tube, seal and harness. Test cycled, all checks ok."

We serviced a

KENMORE DRYER-ELECTRIC

Model 11067522600

Near Wylie, TX 75098

Jacob P.

Job Details: 12/22/2021

"Customer concern of unit not drying well. Ran air flow test, failed. Advised customer vent from back of dryer to outside needs to be cleaned. Hooked dryer vent up to separate exhaust per customer's request."

We serviced a

WHIRLPOOL RANGE

Model GW397LXUS06

Near Bonney Lake, WA 98391

Branden W.

Job Details: 12/22/2021

Customer concern is that oven makes a popping noise when in use. Found bake ignitor only draws 2.8 amps not 3.2 causing low gas flow. Replaced ignitor. Cycle tested at 350. All checks good. ; used 1 WB13K21 (OVEN IGNITER-12' LEAD W/NUTS) from stock

We serviced a

GE COOKTOP

Model JGCP436WP01

Near Dallas, TX 75248

Jacob P.

Job Details: 12/22/2021

"Customer concern of front left burner not igniting. Customer advised burner started working this morning. Cleaned orifice. Test cycled, all checks ok."

We serviced a

GE RANGE

Model JB910S0L1SS

Near Graham, WA 98338

Branden W.

Job Details: 12/22/2021

"Customer concern is that broil, roast and convection bake stopped working. Tested all 4 elements (bake, convection, broil and warming drawer) all elements ohm properly. Cycle tested each cooking option. All working properly at this time. Tested to 350. Advised to call if issue returns."

We serviced a

LG WASHER-FRONTLOAD

Model WM3670HWA

Near Spanaway, WA 98387

Branden W.

Job Details: 12/22/2021

Customer concern is that washer will not drain. Found failed drain pump causing no drain. Replaced pump. Cycle tested. All checks ok. ; used 1 4681EA2001T (DRAIN PUMP) from stock

We serviced a

SAMSUNG WASHER-TOPLOAD

Model WA50F9A7DSW/A2

Near Enumclaw, WA 98022

Branden W.

Job Details: 12/22/2021

"Customer concern is that clothes are not spinning properly. Wet at end of cycle. Found nF (no fill) error stored. Unit not filling with cold water, found unit stops in final rinse cycle due to not filling fast enough leaking the clothes not spun out. Cleaned plugged inlet screen. Cycle tested with load of towels. Unit fills, washes and spins properly. Only other issue found is washplate cap is broken causing it to fall off. Needs new cap. Part number DC66-00777A"

We serviced a

HOTPOINT WASHER-TOPLOAD

Model HSWP1000M3WW

Near Irving, TX 75060

Jacob P.

Job Details: 12/22/2021

"Installed previously ordered drain pump. Test cycled, all checks ok."

We serviced a

GE COOKTOP

Model PP975BM3BB

Near Wylie, TX 75098

Jacob P.

Job Details: 12/22/2021

"Installed previously ordered glass top. Test cycled, all checks ok."

We serviced a

FRIGIDAIRE RANGE

Model FGEF3035RFA

Near Plano, TX 75074

Jacob P.

Job Details: 12/22/2021

"Customer concern of door handle fallen off. Applied loctite to handle threads as be reattached handle. Test cycled, all checks ok."

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV42H5000EW/A3 03

Near Spanaway, WA 98387

Branden W.

Job Details: 12/22/2021

"Customer concern is that dryer does not heat and shuts off. Found open thermal cut off causing no heat. Found motor packed with lint causing it to overheat and shut down. Also found failed rear left roller. Replaced entire heating elememt assembly and roller. Vacuumed inside of dryer. Cleaned moisture sensor. Performed airflow test. Test failed. Advised customer that dryer should not be used until proper exhaust airflow to the outside of the house is restored otherwise dryer will fail again and is a fire hazard. ; used 1 DC97-14486A (ELEMENT ASSEMBLY), and 1 DC97-16782A (DRUM ROLLER) from stock"

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWC425BW0

Near Bonney Lake, WA 98391

Branden W.

Job Details: 12/22/2021

Customer concern is that washer took over an hour to start cycle and made grinding noise. Found failed shift actuator causing unit to not properly shift between spin and agitate and also produce noise. Replaced actuator. Cycle tested. All checks ok. ; used 1 WPW10006355 (ACTUATOR) from stock

We serviced a

GE DRYER-ELECTRIC

Model DPXR483EA1WW

Near Allen, TX 75013

Jacob P.

Job Details: 12/22/2021

"Installed previously ordered heating element. Test cycled, all checks ok."

We serviced a

GE WALL OVEN

Model JT952W0F3WW

Near Irving, TX 75063

Jacob P.

Job Details: 12/22/2021

"Installed previously ordered bottom pan, inner door panel and door lock. Test cycled, all checks ok."

We serviced a

GE WALL OVEN

Model JTS5000SN1SS

Near Grand Prairie, TX 75052

Jacob P.

Job Details: 12/22/2021

"Customer concern of unit tripping breaker. Unhooked power from unit, breaker still trips. Advised customer electrician is needed to correct issue."

We serviced a

MAYTAG DISHWASHER

Model MDBH965AWS

Near Milton, WA 98354

Branden W.

Job Details: 12/21/2021

Customer concern is that dishwasher console buttons do not work. Found failing console causing some buttons to not operate. Needs new console 6-919836. Part is no longer available. Unable to repair dishwasher.

We serviced a

WHIRLPOOL WALL OVEN

Model RBD275PDB15

Near Milton, WA 98354

Branden W.

Job Details: 12/21/2021

Customer concern is that oven board display is out and unit does not operate. Oven operating properly at time of service. Took unit apart. Found no loose or corroded connections. Most likely issue is failure in main control. Main control is no longer available. Only available via rebuild. Declined repair at this time.

We serviced a

KENMORE DISHWASHER

Model 66513593K600

Near Puyallup, WA 98373

Branden W.

Job Details: 12/21/2021

Customer concern is that dishwasher does not work or clean. Found float switch stuck up causing unit to not fill causing it to not clean. Cleaned and reset float. Cycle tested. All checks good.

We serviced a

SAMSUNG DRYER-GAS

Model DV50K7500GV

Near McKinney, TX 75070

Jacob P.

Job Details: 12/21/2021

"Customer concern of dryer not starting, unable to change cycle. Found child lock on causing issue. Turned child lock off. Test cycled, all checks ok."

We serviced a

WHIRLPOOL DISHWASHER

Model WDF320PADS2

Near Lake Tapps, WA 98391

Branden W.

Job Details: 12/21/2021

Installed new element. Cycle tested. Unit heating properly.

We serviced a

SAMSUNG DISHWASHER

Model DW80R9950US/AA 01

Near Murphy, TX 75094

Jacob P.

Job Details: 12/21/2021

"Installed previously ordered trim piece. Test cycled, all checks ok."

We serviced a

GE DISHWASHER

Model GDT695SFL5DS

Near Bonney Lake, WA 98391

Branden W.

Job Details: 12/21/2021

"Installed new ui board. Unit operating properly. Floor does not go under dishwasher and is not cut evenly across opening causing dishwasher to sit behind flooring lip. Side mount bracket missing, top mounting brackets bent and no mounting possible with countertop from ledger board. Installed dishwasher where is would not fall forward and sits level."

We serviced a

WHIRLPOOL WASHER-FRONTLOAD

Model LXR7244JQ3

Near Wylie, TX 75098

Jacob P.

Job Details: 12/21/2021

"Installed previously ordered motor. Test cycled, all checks ok."

We serviced a

FRIGIDAIRE DISHWASHER

Model FGID2474QF1B

Near Frisco, TX 75035

Jacob P.

Job Details: 12/20/2021

"Customer concern of unit washing poorly. Found unit installed incorrectly causing unit to tip forward and wash poorly. Leveled unit, unable to correct issue completely due to size of cavity for dishwasher. Test cycled, checks ok."

We serviced a

GE WALL OVEN

Model PT916SM3SS

Near Plano, TX 75025

Jacob P.

Job Details: 12/20/2021

"Installed previously ordered control panel. Test cycled, all checks ok."

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV456ETHDSU/AA

Near Puyallup, WA 98373

Branden W.

Job Details: 12/20/2021

Customer concern is that dryer makes squealing noise. Found seizing idler pulley causing noise. Replaced pulley. Cycle tested. All checks good. ; used 1 DC93-00634A (IDLER ASSEMBLY) from stock

We serviced a

KENMORE RANGE

Model 79074032313

Near Plano, TX 75074

Jacob P.

Job Details: 12/20/2021

"Customer concern of front right burner not igniting. Found plugged orifice causing no ignition. Cleaned orifice. Test cycled, all checks ok."

We serviced a

GE DISHWASHER

Model GDT695SSJ2SS

Near Allen, TX 75013

Jacob P.

Job Details: 12/20/2021

"Installed previously ordered ui board. Test cycled, all checks ok."

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DVE45R6100P/A3

Near Orting, WA 98360

Branden W.

Job Details: 12/20/2021

Customer concern is that dryer does not heat. Found open heating element causing no heat. Replaced element. Cycle tested. Unit heating. Performed airflow test. Test failed. Advised to have dryer duct cleaned ASAP. ; used 1 DC97-14486A (ELEMENT ASSEMBLY) from stock

We serviced a

ELECTROLUX WASHER-TOPLOAD

Model EIFLW50LIW1

Near Frisco, TX 75035

Jacob P.

Job Details: 12/20/2021

"Installed previously ordered inlet valve. Test cycled, all checks ok."

We serviced a

GE DRYER-ELECTRIC

Model GTD65EBSJ4WS

Near Frisco, TX 75034

Jacob P.

Job Details: 12/20/2021

"Customer concern of unit making loud noise and vent fallen off back of machine. Found screws for rear bearing mount loose causing drum to fall. Installed new screws on bearing mount, attached vent to back of dryer. Test cycled, all checks ok."

We serviced a

LG RANGE

Model LRE3194BD

Near DuPont, WA 98327

Branden W.

Job Details: 12/20/2021

Customer concern is that range intermittently will not operate any heating components (oven or cooktop) found loose wall plug causing unit to lose 240v and not operate elements. Advised electrician is needed to replace wall receptacle. No issues found with range.

We serviced a

WHIRLPOOL COOKTOP

Model W5CG3024XS01

Near Irving, TX 75063

Jacob P.

Job Details: 12/20/2021

"Installed previously ordered valve. Test cycled, all checks ok."

We serviced a

HOTPOINT WALL OVEN

Model RK777G0T6BG

Near Dallas, TX 75254

Jacob P.

Job Details: 12/20/2021

Customer concern of unit not running self clean. Instructed customer on equipment use. Unit functioning as designed.

We serviced a

GE DISHWASHER

Model GLD5660V00SS

Near Irving, TX 75063

Jacob P.

Job Details: 12/17/2021

"Installed new console. Test cycled, all checks ok."

We serviced a

KITCHENAID RANGE

Model KFDD500ESS02

Near Edgewood, WA 98371

Branden W.

Job Details: 12/17/2021

"Customer concern is that range produced F2 E0 (keypad not connected) error. After clearing error is has not returned. Cycle tested all button outputs, removed and reseated ribbon cable from keypad to main control. Unable to reproduce issue. Reset main control. Advised to call if issue returns."

We serviced a

GE DISHWASHER

Model GDT545PSJ2SS

Near Bonney Lake, WA 98391

Branden W.

Job Details: 12/17/2021

Installed new control board. Cycle tested. All checks good.

We serviced a

FRIGIDAIRE WALL OVEN

Model FGEW3045KFB

Near Coppell, TX 75019

Jacob P.

Job Details: 12/17/2021

"Installed previously ordered control board and console. Test cycled, all checks ok."

We serviced a

KENMORE DRYER-ELECTRIC

Model 110.965901

Near McKinney, TX 75069

Jacob P.

Job Details: 12/17/2021

"Installed previously ordered motor, blower, pulley and belt. Test cycled, all checks ok."

We serviced a

WHIRLPOOL WASHER-TOPLOAD

Model WTW8500DC0

Near Spanaway, WA 98387

Branden W.

Job Details: 12/17/2021

Installed new lid lock. Cycle tested. Checks good.

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV350AEW/XAA

Near Garland, TX 75044

Jacob P.

Job Details: 12/17/2021

"Customer concern of dryer not turning on. Found broken belt and seized idler pulley causing no start. Replaced belt and idler pulley. Test cycled, all checks ok. ; used 1 DC93-00634A (IDLER ASSEMBLY), and 1 6602-001655 (BELT) from stock"

We serviced a

LG WASHER-TOPLOAD

Model WM8000HVA

Near Plano, TX 75093

Jacob P.

Job Details: 12/17/2021

"Customer concern of unit leaking out rear of washer and into garage. Pulled unit out, no signs of water and no water damage to wall. Advised customer that water in garage is not from washer. Unit functioning as designed."

We serviced a

GE DRYER-ELECTRIC

Model GFD45ESPM1DG

Near Puyallup, WA 98375

Branden W.

Job Details: 12/17/2021

Installed new front bearing assembly. Cycle tested. All checks ok.

We serviced a

KITCHENAID RANGE

Model KGRS505XSS02

Near Gig Harbor, WA 98335

Branden W.

Job Details: 12/16/2021

Installed new manifold and knobs. Cycle tested. All checks good.

We serviced a

WHIRLPOOL DISHWASHER

Model WDT710PAYM6

Near McKinney, TX 75071

Jacob P.

Job Details: 12/16/2021

"Installed previously ordered heating element. Test cycled, all checks ok."

We serviced a

GE RANGE

Model JBP26WY7WW

Near Wylie, TX 75098

Jacob P.

Job Details: 12/16/2021

"Installed previously ordered control board, overlay, temp probe and bake element. Test cycled, all checks ok."

We serviced a

GE DISHWASHER

Model GDF520PGJ5WW

Near Wylie, TX 75098

Jacob P.

Job Details: 12/16/2021

"Installed previously ordered heating element. Test cycled, all checks ok."

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV22K6800EW/A1 11

Near Gig Harbor, WA 98335

Branden W.

Job Details: 12/16/2021

Installed new rear bearing. Cycle tested. All checks good.

We serviced a

KENMORE DRYER-ELECTRIC

Model 11060222510

Near Rockwall, TX 75032

Jacob P.

Job Details: 12/16/2021

"Customer concern of unit making loud noise. Found worn idler pulley causing noise. Also found debris in felt strip. Removed debris. Replaced pulley. Test cycled, all checks ok. ; used 1 WP691366 (PULLEY-IDR) from stock"

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV50F9A7EVP/A2

Near Frisco, TX 75035

Jacob P.

Job Details: 12/16/2021

"Customer concern of no heat. Found open heating element causing no heat. Also found seized idler pulley. Replaced heating element and idler pulley. Test cycled, all checks ok. ; used 1 DC97-14486A (ELEMENT ASSEMBLY), and 1 DC93-00634A (IDLER ASSEMBLY) from stock"

We serviced a

GE DISHWASHER

Model GSD6960N10SS

Near Puyallup, WA 98373

Branden W.

Job Details: 12/16/2021

Advised that both likely parts causing no heat (heating element and control board) are no longer available on this model. Customer declined service. No trip was made. NO CHARGE

We serviced a

KITCHENAID WALL OVEN

Model KODE500ESS

Near Steilacoom, WA 98388

Branden W.

Job Details: 12/16/2021

Customer concern is that upper oven does not go past 300. Model and serial tag is missing. Cycle tested at 350 and 425. Temperatures in range. Unable to reproduce issue at this time.

We serviced a

KENMORE DISHWASHER

Model 66514573N612

Near Garland, TX 75040

Jacob P.

Job Details: 12/15/2021

"Customer concern of unit not draining. Found debris in drain pump causing no drain. Removed drain pump. Test cycled, all checks ok."

We serviced a

GE RANGE

Model JB655DK7WW

Near Spanaway, WA 98387

Branden W.

Job Details: 12/15/2021

Installed new lamp assembly. Cycle tested. All checks good.

We serviced a

WHIRLPOOL DISHWASHER

Model DU1055XTSS2

Near Garland, TX 75040

Jacob P.

Job Details: 12/15/2021

"Installed previously ordered vent and seals. Test cycled, all checks ok."

We serviced a

KITCHENAID DISHWASHER

Model KDTE334GPS0

Near Spanaway, WA 98387

Branden W.

Job Details: 12/15/2021

Customer concern is that dishwasher does not close after customer pulled on door. and unit not powering on. Found door hinges came out of socket causing door to not close. Reset hinges. Found main control losing stored power causing no operation. Reset power and all buttons responding properly. Will need new main control. Declined to repair at this time.

We serviced a

KITCHENAID RANGE

Model KGRS505XSS02

Near Puyallup, WA 98374

Branden W.

Job Details: 12/15/2021

"Installed new ignitors, manifold and valve. Cycle tested all burners. All check good. Brought lower oven to 450 and upper to 350. All checks good."

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAHZ0

Near Dallas, TX 75214

Jacob P.

Job Details: 12/15/2021

"Installed previously ordered spray arms. Test cycled, all checks ok."

We serviced a

KENMORE DRYER-ELECTRIC

Model 11069632800

Near Fox Island, WA 98333

Cameron M.

Job Details: 12/14/2021

"Installed sears provided dryer motor and blower wheel. Cycle tested unit, all checks good. ; used 1 WP694089 (BLOWER WHEEL) from stock"

We serviced a

GE DISHWASHER

Model GDF610PMJ2ES

Near Graham, WA 98338

Branden W.

Job Details: 12/14/2021

Installed new control board. Cycle tested. All checks good.

We serviced a

HOTPOINT WALL OVEN

Model RK777G0T6BG

Near Dallas, TX 75254

Jacob P.

Job Details: 12/14/2021

"Installed previously ordered clock and fan. Test cycled, all checks ok."

We serviced a

LG WASHER-FRONTLOAD

Model WM5000HVA

Near Graham, WA 98338

Branden W.

Job Details: 12/14/2021

Installed new tub springs. Unable to cycle test as unit is outside with no hookups. Advised to run several hot wash cycles for door boot to return to proper shape.

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV42H5200EP/A3 03

Near Tacoma, WA 98408

Cameron M.

Job Details: 12/14/2021

"Customer concern is that dryer makes noise during operation. Found failed right rear and left front rollers ,causing noise during operation. Needs new rollers. Installed rollers. Cleaned and calibrated moisture sensors. Vacuumed inside of unit. Preformed airflow test, failed (yellow). Cycle tested unit ; used 2 DC97-16782A (DRUM ROLLER) from stock"

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV48H7400EW/A2 02

Near Rockwall, TX 75032

Jacob P.

Job Details: 12/14/2021

"Customer concern of unit not tumbling. Found worn idler pulley causing belt to fall off. Replaced idler pulley. Test cycled, all checks ok. ; used 1 DC93-00634A (IDLER ASSEMBLY) from stock"