We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM7
Near Bonney Lake, WA 98391
Branden W.
Job Details:
12/14/2021
Customer concern is that dishwasher does not heat and dry. Found dishwasher in heat lockout causing no heat. Reset via service cycle. Cycle tested. Unit heating properly. All checks good.
We serviced a
FRIGIDAIRE DISHWASHER
Model PLD2855RFC0
Near Dallas, TX 75252
Jacob P.
Job Details:
12/14/2021
"Installed previously ordered wash pump. Test cycled, all checks ok."
We serviced a
SAMSUNG WASHER-TOPLOAD
Model WA45H7000AW/A2 01
Near Graham, WA 98338
Branden W.
Job Details:
12/14/2021
Customer concern is that washer leaks and produces error. Found pressure hose came off of tub causing issues. Reinstalled hose. Cycle tested. Found noise from drive system. Took rotor apart and found splines worn causing noise. Needs new motor assembly. Declined repair at this time.
We serviced a
KENMORE DISHWASHER
Model 66516033401
Near Puyallup, WA 98373
Branden W.
Job Details:
12/13/2021
Customer concern is that dishwasher does not operate. Found dishwasher in heat lockout out causing no operation. Found failed control not sending voltage to heating element causing lock out. Control board is discontinued. Board needed is WP8564547Unable to repair dishwasher.
We serviced a
KITCHENAID DISHWASHER
Model KDTE104ESS1
Near Dallas, TX 75218
Jacob P.
Job Details:
12/13/2021
"Installed previously ordered lower rollers. Test cycled, all checks ok."
We serviced a
GE DISHWASHER
Model GSD3300D00BB
Near Spanaway, WA 98387
Branden W.
Job Details:
12/13/2021
"Customer concern is that dishwasher leaks. Found dishwasher leaking from detergent lid shaft opening on inner panel. Removed and cleaned all parts. Reinstalled. Cycle tested. No leaks. Advised if issue persists, will need new inner panel, seal and detergent cap and shaft. Also found airgap leaking undersink. Cleaned hose from gap to disposal causing backup and leak. Advised airgap should be installed through sink. Declined repair at this time."
We serviced a
LG WASHER-FRONTLOAD
Model WM3470HWA
Near Orting, WA 98360
Branden W.
Job Details:
12/13/2021
Customer requests pm check. Performed preventative maintenance check on washer. Found drain hose too far in wall drain. Set to proper depth and secured. Found no issues with washer.
We serviced a
KENMORE RANGE
Model 7907136370A
Near Frisco, TX 75035
Jacob P.
Job Details:
12/13/2021
"Customer concern of loud bang in oven few minutes after starting. Found weak igniter causing slow ignition. Replaced igniter. Test cycled, checks ok. Customer concern of back right burner not burning to full capacity. Test cycled, unable to verify complaint. Instructed customer how to remove burner parts and clean them. Customer concern of front right burner going out when turned on low. Test cycled, unable to verify complaint. Turned all gas valves up per customer's request. Unit functioning as designed. ; used 1 WB13K21 (OVEN IGNITER-12' LEAD W/NUTS) from stock"
We serviced a
KENMORE DRYER-ELECTRIC
Model 11066752500
Near Spanaway, WA 98387
Branden W.
Job Details:
12/10/2021
Customer concern is that dryer does not heat. Found unit heating properly but has no airflow. Found outside vent cap plugged causing issues. Cleared vent cap. All checks good.
We serviced a
ELECTROLUX WASHER-FRONTLOAD
Model EIFLS60LT1
Near McKinney, TX 75069
Jacob P.
Job Details:
12/10/2021
"Installed previously ordered shocks. Test cycled, all checks ok."
We serviced a
LG WASHER-FRONTLOAD
Model WM3700HVA 02
Near Graham, WA 98338
Branden W.
Job Details:
12/10/2021
Installed new hose. Cycle tested. All checks ok.
We serviced a
LG WASHER-FRONTLOAD
Model WM2277HW
Near Spanaway, WA 98387
Branden W.
Job Details:
12/10/2021
Customer concern is that washer leaks. Found cold inlet valve leaking water. Replaced valve. Cycle tested. All checks good. ; used 1 5220FR2075L (INLET VALVE-COLD) from stock
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WF45N5300AV/US
Near South Hill, WA 98373
Cameron M.
Job Details:
12/10/2021
"Customer concern is that washer does not drain and spin. Found unit oversuded, causing slow drain condition. flushed suds out of unit, Via rinse and spin. Cycle tested unit. All checks good. Advised customer on using high quality detergent. Also advised customer on regular cleaning intervals for optimal performance of washer."
We serviced a
FRIGIDAIRE WALL OVEN
Model FEB786CESH
Near Tacoma, WA 98446
Branden W.
Job Details:
12/10/2021
"Installed new convection fan motor, door lock motor, temp sensor and rebuilt main control. Rebuilt board is worse than before. Called AHS to advise. They are putting it into replacement. Auth 439kvbm"
We serviced a
AMANA DRYER-GAS
Model NED4655EW0
Near Forney, TX 75126
Jacob P.
Job Details:
12/10/2021
"Customer concern of dryer vent fallen off. Installed customer provided vent. Test cycled, all checks ok."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT710PAHW1
Near Tacoma, WA 98408
Cameron M.
Job Details:
12/10/2021
"Customer concern is that dishwasher dose not operate during wash cycle. Found loose connection at wash pump, reseated connection, cycle tested unit x15, all checks good"
We serviced a
GE RANGE
Model P2B918SEM3SS
Near Spanaway, WA 98387
Branden W.
Job Details:
12/10/2021
"Customer concern is that new control board worked for about a week, then all lights came on and timer kept going off every 3 minutes. Customer turned breaker off and when turned back on, issue has not happened. Cycle tested all buttons, no issues. Test cycled board outputs, no issues. Unable to reproduce issue at this time. Advised AHS that control board is most likely cause of issues. AHS declined to replace control as it is not currently producing issues. Advised customer to call if issue returns. Auth 109mri"
We serviced a
AMANA DISHWASHER
Model ADB1000AWW1
Near Puyallup, WA 98373
Branden W.
Job Details:
12/10/2021
"Customer concern is that dishwasher does not operate at all. Has not for about 3 years. Found water fill hose to dishwasher broken off undersink. Unable to water test. Tested components, all operate ok. Found no issues with dishwasher. Advised to restore water to unit and call if any issues persists. Advised new supply hose needed, hose is not part of dishwasher. Plumber needed."
We serviced a
GE DISHWASHER
Model GLD5860L00SS
Near Frisco, TX 75034
Jacob P.
Job Details:
12/10/2021
"Customer concern of detergent door not opening. Found loose connection at dispenser causing door not to open. Reseated connection. Test cycled, all checks ok."
We serviced a
MAYTAG DRYER-ELECTRIC
Model MEDB855DC4
Near Eatonville, WA 98328
Cameron M.
Job Details:
12/10/2021
"Customer concern is that dryer makes humming noise during operation. Found rag in blower wheel, causing unit to make noise during operation. Removed rag. Preformed airflow test failed (yellow) cycle tested unit. All checks good"
We serviced a
GE COOKTOP
Model NOTAVAILABLE
Near Frisco, TX 75035
Jacob P.
Job Details:
12/09/2021
"Customer concern of flames being yellow and not blue. Advised customer running humidifier or change in atmosphere causes flame color to change, not the appliance. Test cycled all burners, all checks ok. ; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #)"
We serviced a
KITCHENAID DISHWASHER
Model KDTE104DSS0
Near McKinney, TX 75070
Jacob P.
Job Details:
12/09/2021
"Installed previously ordered left track and customer provided right track. Test cycled, all checks ok."
We serviced a
SAMSUNG DISHWASHER
Model DW80K7050UG/AA 03
Near Puyallup, WA 98374
Branden W.
Job Details:
12/09/2021
Customer concern is that dishwasher produced LC error mid cycle and would not drain. Unit removed and taken apart prior to service. Found broken glass lodged in drain pump housing causing issues. Removed glass. Cycle tested. Found drain hose loose at airgap causing leak. Tightened clamp. Cycle tested. All checks ok. Advised customer that we can not reassemble as we have to leave it how it was upon arrival.
We serviced a
KENMORE WASHER-TOPLOAD
Model 11022352511
Near University Place, WA 98466
Cameron M.
Job Details:
12/09/2021
Customer concern is that washer not rinsing clothes completely. Cycle tested unit 3x with customer provided load of towels. Found no mechanical issues at this time. Unit operating as designed. Advised customer on proper loading practices. Also advised customer on using high quality detergent for best wash results.
We serviced a
GE DISHWASHER
Model GDT655SSJ5SS
Near Dallas, TX 75219
Jacob P.
Job Details:
12/09/2021
"Customer concern of unit not filling. Found unit not draining, removed debris from drain hose causing no drain. Unit now drains and fills. All checks ok."
We serviced a
GE WALL OVEN
Model JK3000SF5SS
Near Frisco, TX 75035
Jacob P.
Job Details:
12/09/2021
"Customer concern of unit sparking and smoking. Test cycled, unable to verify complaint. Found lots of debris built up in cavity. Advised customer running clean cycle is recommended. Unit functioning as designed."
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WF42H5200AF/A2 11
Near Spanaway, WA 98387
Branden W.
Job Details:
12/09/2021
Customer would like preventive maintenance check done. Performed maintenance check. Drain hose was too far in wall drain. Corrected depth and secured with zip tie. Cleaned pump. Cycle tested. All checks good. Advised to clean door boot and inner dispenser regularly and run self clean cycle regularly. Washer operating as designed.
We serviced a
ELECTROLUX DRYER-ELECTRIC
Model EFME617SIW0
Near Puyallup, WA 98374
Branden W.
Job Details:
12/09/2021
Installed new valve. All checks ok.
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV45K6200EZ/A3 01
Near Spanaway, WA 98387
Cameron M.
Job Details:
12/09/2021
"Customer concern is that dryer makes noise during operation. Preformed airflow test, failed (red).found rear rollers breaking down,causing noise during operation. Also found seized front left roller ,causing noise during operation. Needs new rollers. Cleaned and calibrated moisture sensors. Cleaned and Vacuumed inside of unit. Installed new rollers cycle tested unit. All checks good. Advised customer dryer vent duct needs to be cleaned asap, before use resumes for dryer to prevent further issues. ; used 3 DC97-16782A (DRUM ROLLER) from stock"
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW5000DW2
Near Tacoma, WA 98404
Cameron M.
Job Details:
12/08/2021
Installed previously ordered main control board. Cycle tested unit. All checks good.
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV42H5200EF/A3 01
Near Puyallup, WA 98373
Cameron M.
Job Details:
12/08/2021
Installed previously ordered door switch. Cycle tested unit all checks good
We serviced a
WHIRLPOOL RANGE
Model WEG745H0FS0
Near Puyallup, WA 98371
Branden W.
Job Details:
12/08/2021
Installed new harness and knob. Cycle tested. All checks good.
We serviced a
MAYTAG DRYER-ELECTRIC
Model MEDC465HW
Near Plano, TX 75074
Jacob P.
Job Details:
12/08/2021
Found no issue with unit.
We serviced a
KENMORE WASHER-FRONTLOAD
Model 11045962400
Near DuPont, WA 98327
Cameron M.
Job Details:
12/08/2021
"Installed previously ordered inlet valve. Cycle tested unit, all checks good."
We serviced a
KENMORE RANGE
Model 79072903015
Near Frisco, TX 75034
Jacob P.
Job Details:
12/08/2021
"Installed previously ordered igniters, spark module and harness. Test cycled, all checks ok."
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WF42H500AW/A2 11
Near Puyallup, WA 98373
Branden W.
Job Details:
12/08/2021
Customer concern is that washer leaks a lot of water. Found hose from dispenser to tub came off tub causing leak. Reinstalled hose. Cycle tested. All checks good.
We serviced a
AMANA RANGE
Model AER6303MFS2
Near Tacoma, WA 98446
Cameron M.
Job Details:
12/08/2021
Customer concern is that oven temperatures are not what they should be. Cycle tested unit 10x unit heated to correct temperature every time. Found no mechanical issues at this time. Unit operating as designed
We serviced a
GE DISHWASHER
Model GDT695SMJ2ES
Near Lewisville, TX 75067
Jacob P.
Job Details:
12/08/2021
"Installed previously ordered ui board. Test cycled, all checks ok."
We serviced a
FRIGIDAIRE DISHWASHER
Model FDSH450LAF1A
Near Dallas, TX 75214
Jacob P.
Job Details:
12/08/2021
"Installed previously ordered dispenser. Test cycled, all checks ok."
We serviced a
JENN-AIR WALL OVEN
Model JJW9830DDP
Near Frisco, TX 75035
Jacob P.
Job Details:
12/07/2021
"Installed previously ordered cooling fan and repaired control board. Test cycled, all checks ok."
We serviced a
KITCHENAID DISHWASHER
Model KDTE334GPS0
Near Irving, TX 75060
Jacob P.
Job Details:
12/07/2021
"Installed previously ordered sump assembly. Test cycled, all checks ok. Left failed part with customer."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE52M7750V/A3
Near Sumner, WA 98390
Branden W.
Job Details:
12/07/2021
Customer concern is that dryer makes noise. Unable to reproduce issue. All rollers and idler in good condition. Tested with load. No abnormal noises heard at this time.
We serviced a
KENMORE WASHER-TOPLOAD
Model 11026132413
Near Spanaway, WA 98387
Branden W.
Job Details:
12/07/2021
Customer concern is that washer intermittently does not operate. Found failed lid lock not sensing lid is closed causing unit to not operate. Replaced lid lock. Cycle tested. All checks good. Collected 75.00 deductible via card. ; used 1 W10810403 (LID LOCK ASSY) from stock
We serviced a
GE WASHER-FRONTLOAD
Model GFW650SSN0WW
Near Lakewood, WA 98498
Cameron M.
Job Details:
12/07/2021
Customer concern is that user interface is intermittently unresponsive and intermittently activates without customer interaction. Cycle tested unit 10x without issue. Tested user interface 20x found no issues. Unit operating as designed. Advised customer to monitor and call if issue persists.
We serviced a
GE DISHWASHER
Model GLD5660V00SS
Near Irving, TX 75063
Jacob P.
Job Details:
12/07/2021
"Installed previously ordered control board and assembly. Test cycled, all checks ok."
We serviced a
SAMSUNG WASHER-TOPLOAD
Model WA5471ABW/XAA
Near Tacoma, WA 98405
Cameron M.
Job Details:
12/07/2021
"Installed previously ordered cover,left and right hinges, detergent dispenser, an dispenser drawer. Cycle tested unit. All checks good."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVW7232HW0
Near Orting, WA 98360
Branden W.
Job Details:
12/07/2021
Installed new washplate and cap. Cycle tested. Found drain hose disconnected from washer. Reconnected hose. All checks ok.
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WF45R6100AP/US
Near Buckley, WA 98321
Branden W.
Job Details:
12/07/2021
Customer concern is that washer will not operate in a cycle. Found clogged drain pump causing unit to not run cycle. Cleared pump. Cycle tested. All checks ok. Advised to clean pump filter regularly.
We serviced a
GE DISHWASHER
Model GDF570SGJ4CC
Near Irving, TX 75062
Jacob P.
Job Details:
12/07/2021
"Installed previously ordered ui board. Test cycled, all checks ok."
We serviced a
GE WASHER-FRONTLOAD
Model GFW850SPN0DG
Near Buckley, WA 98321
Branden W.
Job Details:
12/06/2021
"Customer concern is that washer intermittently does not spin properly. Cycle tested, found excessive suds. Flushed suds from basket. Unit spinning at 1100 rpms. Unable to duplicate concern at this time. Advised to use high quality HE detergent and use less detergent. No mechanical issues found with washer at time of service."
We serviced a
LG RANGE
Model LRE3083ST/01
Near Saint Paul, TX 75098
Jacob P.
Job Details:
12/06/2021
"Installed previously ordered control boards. Test cycled, all checks ok."
We serviced a
FRIGIDAIRE DISHWASHER
Model GLD4355RFB0
Near Frisco, TX 75034
Jacob P.
Job Details:
12/06/2021
"Customer concern of unit making loud noise and not washing well. Found water turned off to unit causing no wash and loud wash pump. Turned water on. Test cycled, all checks ok."
We serviced a
KENMORE WASHER-TOPLOAD
Model 11020892990
Near McKinney, TX 75070
Jacob P.
Job Details:
12/06/2021
"Customer concern of unit not agitating. Found worn dog agits causing no agitation. Replaced dog agits. Test cycled, all checks ok. ; used 1 80040 (AGITATOR DOGS) from stock"
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW57ESVW1
Near Tacoma, WA 98406
Cameron M.
Job Details:
12/06/2021
"Customer concern is that washer does not fill. Cycle tested unit 10x, Found shaft of timer stripped out. causing difficulty selecting cycle. Needs new timer."
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM7
Near Sumner, WA 98391
Branden W.
Job Details:
12/06/2021
Installed new wash pump. Cycle tested. All checks good.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF590SAJM0
Near Forney, TX 75126
Jacob P.
Job Details:
12/06/2021
"Customer concern of upper rack falling down. Found adjusters broken causing rack to fall. Replaced adjusters. Test cycled, all checks ok. ; used 1 W10712395 ( ADJUSTER) from stock"
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVW7232HW0
Near Mesquite, TX 75149
Jacob P.
Job Details:
12/06/2021
"Customer concern of unit leaking. Inspected all internal and external hoses, valves and pumps, no signs of water. Test cycled, found stand pipe overflowing when unit drains. Advised customer plumber is needed to fix issue. Unit functioning as designed."
We serviced a
ELECTROLUX DISHWASHER
Model EI24ID81SS0A
Near Bonney Lake, WA 98391
Branden W.
Job Details:
12/06/2021
"Customer concern is that dishwasher trips breaker. Unit unplugged and breaker off prior to service. Plugged unit in found breaker kept tripping. Removed dishwasher. Ohmed all main components, none shorted. Tested again, not tripping breaker but still fails to power on. Per Electrolox, needs new main and console controls. Further issues may exist, unable to test without being able to cycle dishwasher. Declined to repair at this time."
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WF45R6100AC/US
Near Bonney Lake, WA 98391
Branden W.
Job Details:
12/06/2021
Customer concern is that washer does not drain and spin. Found clogged pump causing unit to not drain or spin. Cleared pump. Cycle tested. All checks good.
We serviced a
KENMORE DRYER-ELECTRIC
Model 11065132411
Near Buckley, WA 98321
Cameron M.
Job Details:
12/03/2021
"Customer concern is that dryer door seal is fraying. Preformed airflow test pass (green) .found dryer door seal is damaged and coming apart. Needs new door seal, installed new door seal. Cycle tested unit all checks good; used 1 W10906683 (SEAL-DOOR) from stock"
We serviced a
SAMSUNG DISHWASHER
Model DW80R9950US/AA 01
Near Puyallup, WA 98373
Branden W.
Job Details:
12/03/2021
"Customer concern is that dishwasher was not starting cycle. Had to set it to delay start to be able to get dishwasher to operate, then unit started working again, also concern that it is not drying properly. Cycle tested through different cycles, unit started properly every time. Ran full factory diagnostic and calibration cycles. Unit operating as designed at this time. Advised to make sure drying agent is being used."
We serviced a
GE DISHWASHER
Model GDT605PSM0SS
Near Garland, TX 75044
Jacob P.
Job Details:
12/03/2021
"Test cycled unit, all checks ok."
We serviced a
WHIRLPOOL COOKTOP
Model GJC3634RC00
Near Rowlett, TX 75088
Jacob P.
Job Details:
12/03/2021
"Replaced knob, all checks ok."
We serviced a
MAYTAG DRYER-ELECTRIC
Model MDE5500AYW
Near Puyallup, WA 98374
Branden W.
Job Details:
12/03/2021
Installed new belt. Cycle tested. All checks good.
We serviced a
AMANA WASHER-TOPLOAD
Model NTW4516FW1
Near Puyallup, WA 98371
Cameron M.
Job Details:
12/03/2021
"Customer concern is that washer pump stays on and no lights are turning on. Tested unit for error codes. Found customer incorrectly Canceled cycle, causing unit to attempt completion of previous cycle. Cancel previous cycle, cycle tested unit 5x. Found no mechanical issues at this time. Unit operating as designed."
We serviced a
FRIGIDAIRE WASHER-FRONTLOAD
Model FAFW3001LW3
Near Tacoma, WA 98404
Cameron M.
Job Details:
12/03/2021
Installed previously ordered door clamp. Cycle tested unit all checks good.Advised customer on regular cleaning intervals for optimal wash profomance.
We serviced a
SAMSUNG WASHER-TOPLOAD
Model WA52J8700AP/AA
Near Graham, WA 98338
Branden W.
Job Details:
12/03/2021
Customer concern is that washer makes noise at beginning of the cycle. Cycle tested empty and with a load of towels. No abnormal noises heard. All components check good. No issues found at this time.
We serviced a
WHIRLPOOL DISHWASHER
Model DU1055XTVS8
Near Orting, WA 98360
Branden W.
Job Details:
12/03/2021
Installed new heating element and mounting bracket. Cycle tested. All checks good.
We serviced a
AMANA DRYER-ELECTRIC
Model NED4655EW1
Near Puyallup, WA 98375
Cameron M.
Job Details:
12/03/2021
"Customer concern is that dryer makes grinding noise during operation. Preformed airflow test, passed (green) found debris in blower housing causing noise during operation, removed debris cycle tested unit all checks good"
We serviced a
AMANA DRYER-ELECTRIC
Model NED4600YQ1
Near Tacoma, WA 98444
Cameron M.
Job Details:
12/03/2021
"Installed previously ordered timer, cycle tested unit all checks good. Advised customer dryer vent hose needs to be shortened to allow sufficient airflow."
We serviced a
KENMORE DRYER-ELECTRIC
Model 11066904690
Near Dallas, TX 75217
Jacob P.
Job Details:
12/03/2021
"Customer concern of unit not heating. Found burnt wire to element causing no heat. Replaced connector. Test cycled, all checks ok."
We serviced a
KITCHENAID DISHWASHER
Model KUDC10FXSS5
Near Sunnyvale, TX 75182
Jacob P.
Job Details:
12/03/2021
"Installed previously ordered accumulator, door seal and gasket. Customer concern of unit not draining. Found plug still in garbage disposal causing no drain. Removed plug. Test cycled, all checks ok. Advised customer that when sink fills up, garbage disposal leaks."
We serviced a
FRIGIDAIRE DISHWASHER
Model FFID2426TS2A
Near Garland, TX 75043
Jacob P.
Job Details:
12/02/2021
"Installed previously ordered control board and dispenser. Test cycled, all checks ok."
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW6120HW0
Near Enumclaw, WA 98022
Branden W.
Job Details:
12/02/2021
Customer concern is that washer stopped mid cycle and would not operate. Customer tried to use washer after leaving it unplugged and washer has been operating properly. Found no stored erros. Cycle tested numerous times. Unit operating as designed at this time.
We serviced a
KENMORE WASHER-TOPLOAD
Model 11022352512
Near Tacoma, WA 98406
Cameron M.
Job Details:
12/02/2021
"Customer concern is that washer does not agitate. Found shifter not engaged with clutch assembly. Re-engaged shifter and clutch assembly, cycle tested unit 5x. All checks good"
We serviced a
KENMORE LAUNDRY CENTER
Model 41761723510
Near Spanaway, WA 98387
Cameron M.
Job Details:
12/02/2021
"Installed previously ordered drain hose, cycle tested unit 3x, all checks good"
We serviced a
LG WASHER-TOPLOAD
Model WM2701HV
Near Allen, TX 75013
Jacob P.
Job Details:
12/02/2021
"Customer concern of unit leaking. Found door boot spring not installed properly causing leak. Reinstalled door boot spring properly. Test cycled, all checks ok."
We serviced a
GE RANGE
Model JB258DM1BB
Near Spanaway, WA 98387
Branden W.
Job Details:
12/02/2021
"Customer concern is that right rear burner does not work and oven does not bake properly. Found failed surface burner. Cycle tested oven at 350 and 425 degrees. Temp sensor in range, bake and broil elements good. Proper amp range. Temps in range. Found no issues with oven. Sending surface element direct to customer."
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WF45T6000AW/A5
Near DuPont, WA 98327
Cameron M.
Job Details:
12/02/2021
"Customer concern is that washer does not drain. Found debris in drain pump, causing unit to not drain. Cleaned debris from drain pump clean out, cycle tested unit 3x. All checks good advised customer on using high quality detergent for best wash results. Also advised customer on making sure they check pockets before running laundry."
We serviced a
MAYTAG WASHER-TOPLOAD
Model LAT9700AAW
Near Gig Harbor, WA 98332
Branden W.
Job Details:
12/02/2021
Installed new valve and sleeve. Cycle tested. All checks good.
We serviced a
SAMSUNG WASHER-TOPLOAD
Model WA50R5400AW/US5C 03
Near Tacoma, WA 98446
Branden W.
Job Details:
12/02/2021
"Customer concern is that washer does not work. Language barrier. Cycle tested numerous times. Unit fills, washes, drains and spins without issue. Advised to take video of issue if it persists."
We serviced a
GE WASHER-TOPLOAD
Model GTW465ASN1WW
Near Tacoma, WA 98499
Cameron M.
Job Details:
12/02/2021
"Installed previously ordered lid switch, cycle tested unit 3x. All checks good,."
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WFW81HEDW0
Near Dallas, TX 75225
Jacob P.
Job Details:
12/02/2021
"Customer concern of unit locked and running drain pump. Manually unlocked door. Reset unit. Test cycled, found excess suds in machine. Cleared out suds. Started clean cycle, all checks ok."
We serviced a
GE DISHWASHER
Model GLD6964R10SS
Near Irving, TX 75063
Jacob P.
Job Details:
12/01/2021
"Installed previously ordered inlet valve. Test cycled, all checks ok."
We serviced a
KENMORE WASHER-FRONTLOAD
Model 11025132412
Near Orting, WA 98360
Branden W.
Job Details:
12/01/2021
Customer concern is that washer makes noise in spin cycle. Found drain hose tapping against rear panel causing noise. Repositioned drain hose. All checks ok
We serviced a
ROPER WASHER-TOPLOAD
Model RTW4516FW2
Near Puyallup, WA 98371
Cameron M.
Job Details:
12/01/2021
Customer concern is that washer makes squealing noise during spin cycle cycle tested unit 10x with customer provided load of towels. Unable to duplicate customer concern. Unit operating as designed. Advised customer to monitor and record video if issues persists.
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WF42H200AF/A2 01
Near Puyallup, WA 98373
Branden W.
Job Details:
12/01/2021
Customer concern is washer is not draining all the way. Found clogged drain filter causing slow drain. cleaned out filter cycle tested unit all checks ok.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near McKinney, TX 75071
Jacob P.
Job Details:
12/01/2021
"Customer concern of top rack falling down. Found broken adjusters causing rack to fall. Replaced adjusters. Test cycled, all checks ok. ; used 1 W10712395 (ADJUSTER) from stock"
We serviced a
MAYTAG DRYER-ELECTRIC
Model MEDE300VW0
Near South Hill, WA 98375
Branden W.
Job Details:
12/01/2021
Customer concern is that dryer does not start and screws out of lint filter housing. Reinstalled housing. Unable to get unit to not start. Tested x20. Unit starting properly at this time.
We serviced a
GE DISHWASHER
Model GDT655SSJ2SS
Near Frisco, TX 75035
Jacob P.
Job Details:
12/01/2021
"Installed previously ordered ui board. Test cycled, all checks ok."
We serviced a
KENMORE DRYER-ELECTRIC
Model 11071633610
Near Gig Harbor, WA 98332
Cameron M.
Job Details:
12/01/2021
"Installed previously ordered thermal fuse, cycle tested unit. All checks good. Preformed airflow test pass"
We serviced a
WHIRLPOOL RANGE
Model WFE770H0FZ0
Near Lake Tapps, WA 98391
Branden W.
Job Details:
12/01/2021
Installed new infinite switch. Cycled burner. All checks good
We serviced a
SAMSUNG DRYER-GAS
Model DV45K6200GW/A3 01
Near Tacoma, WA 98406
Cameron M.
Job Details:
12/01/2021
"Customer concern is that dryer makes rattling noise during operation. Found right rear roller, causing noise during operation. Needs new right rear roller. Installed new roller. Cleaned and Vacuumed inside of unit. Cycle tested unit, all checks good ; used 1 DC97-16782A (DRUM ROLLER) from stock"
We serviced a
GE WASHER-TOPLOAD
Model GTW335ASN0WW
Near Dallas, TX 75211
Jacob P.
Job Details:
12/01/2021
"Installed previously ordered transmission, belt and pulley. Test cycled, all checks ok."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV42H5000EW/A3 03
Near Spanaway, WA 98387
Cameron M.
Job Details:
12/01/2021
"Customer concern is that dryer heats up but stops mid cycle unit also takes multiple cyclestodryclothes. Preformed airflow test, failed (red). Preformed temperature checks , in range. Cleaned and calibrated moisture sensors. Advised customer dryer vent duct needs to be cleaned asap before use resumes to prevent damage to element. Also advised customer on proper loading practices. Also advised customer dryer vent hose needs to be shortened to allow sufficient airflow."
We serviced a
KITCHENAID DISHWASHER
Model KDTE254ESS1
Near Puyallup, WA 98374
Cameron M.
Job Details:
11/30/2021
"Installed previously ordered main control board and upper, lower spray arms. Cycle tested unit 3x, all checks good."
We serviced a
KENMORE DISHWASHER
Model 36314171790
Near Irving, TX 75038
Jacob P.
Job Details:
11/30/2021
"Customer concern of unit leaving dishes wet and spots. Test cycled heating element, checks ok. Found good water temps at sink. Found no rinse aid in unit. Advised customer rinse aid is required for proper washing and drying results. Unit functioning as designed."
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model MVWB835DC4
Near Puyallup, WA 98374
Branden W.
Job Details:
11/30/2021
"Installed previously ordered lid lock, cycle tested unit all checks ok"
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB765FW3
Near Tacoma, WA 98445
Cameron M.
Job Details:
11/30/2021
"Installed previously ordered user interface, cycle tested unit. All checks good."
We serviced a
KENMORE RANGE
Model 79042529316
Near Puyallup, WA 98374
Cameron M.
Job Details:
11/30/2021
"Installed previously ordered infinite switch, cycle tested unit. All four burners regulate at proper Temps. All checks good"