We serviced a
SAMSUNG DRYER-ELECTRIC
Model n/a
Near Spanaway, WA 98387
Branden W.
Job Details:
11/12/2021
Customer concern is that dryer does not dry and water in vent. Performed airflow test. Found clogged vent. Advised to have dryer duct cleaned. NO CHARGE
We serviced a
KENMORE WASHER-TOPLOAD
Model 11025132411
Near Eatonville, WA 98328
Cameron M.
Job Details:
11/12/2021
"Installed sears provided basket and gearcase. Cycle tested unit 3x, all checks good."
We serviced a
KENMORE DISHWASHER
Model 66513222N412
Near Edgewood, WA 98372
Branden W.
Job Details:
11/11/2021
Installed new wash pump and grommet. Cycle tested. All checks good.
We serviced a
FRIGIDAIRE DISHWASHER
Model FGID2477RF1A
Near Murphy, TX 75094
Jacob P.
Job Details:
11/11/2021
Customer concern of dishwasher not powering on. Found burnt connection wire causing it not to get power. Replaced wire nut. Tested cycle checks out.
We serviced a
WHIRLPOOL DISHWASHER
Model 58715259400
Near Lakewood, WA 98499
Branden W.
Job Details:
11/11/2021
Installed new main control. Tested in service mode. Elememt operating properly. All checks ok.
We serviced a
FRIGIDAIRE DISHWASHER
Model FFBD2408NS10C
Near Rockwall, TX 75087
Jacob P.
Job Details:
11/11/2021
"Installed previously ordered control board. Test cycled, all checks ok."
We serviced a
SAMSUNG WASHER-TOPLOAD
Model WA54R7600AC/US 01
Near Tacoma, WA 98445
Branden W.
Job Details:
11/11/2021
Customer concern is that washer did not spin and now does nothing. Found pump jammed causing no drain and unit to not run a cycle. Cleared pump. Cycle tested. All checks ok.
We serviced a
SAMSUNG WASHER-TOPLOAD
Model WF45H6300AW/A2
Near Frisco, TX 75034
Jacob P.
Job Details:
11/11/2021
Customer concern of unit leaking on left side when running comforters or rugs. Advised customer the rugs are not machine washable. Found signs of water from vent on rear of machine. Advised that clean cycles need to be ran to break down old detergent buildup to keep unit from venting. Unit functioning as designed.
We serviced a
GE DISHWASHER
Model GSD3360K55SS
Near McKinney, TX 75071
Jacob P.
Job Details:
11/11/2021
"Customer concern of water not draining properly. Found drain line hose wasnt properly installed. Installed high loop under sink. Test cycled, all checks ok."
We serviced a
SAMSUNG WASHER-TOPLOAD
Model WA52M7750AV/A4 01
Near Spanaway, WA 98387
Branden W.
Job Details:
11/10/2021
Installed new pcb. Cycle tested. All checks good.
We serviced a
KITCHENAID DISHWASHER
Model KDTE204EWH1
Near Puyallup, WA 98371
Branden W.
Job Details:
11/10/2021
Installed new pump/motor and detergent dispenser that customer wanted replaced. Cycle tested. All checks good. Customer requested to not keep part that caused leak.
We serviced a
SAMSUNG RANGE
Model NX58F5500SS/AA
Near Plano, TX 75024
Jacob P.
Job Details:
11/10/2021
"Customer concern of bake not working. Found weak igniter causing no heat. Replaced igniter. Test cycled, all checks ok. ; used 1 WB13K21 (OVEN IGNITER-12' LEAD W/NUTS) from stock"
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW5105HW2
Near Puyallup, WA 98374
Cameron M.
Job Details:
11/10/2021
"Customer concern is that washer lid strike broken. Unit only connected to utilities, only set up to power. Found broken lid strike, causing unit to not start cycle. Needs new lid."
We serviced a
MAYTAG DISHWASHER
Model MDB4949SHZ0
Near Dallas, TX 75228
Jacob P.
Job Details:
11/10/2021
"Customer concern of unit not turning on. Found no voltage to unit. Checked breaker, breaker is on and still no voltage to unit. Advised customer that electrician is required to fix issue. Unable to test unit due to no power."
We serviced a
KENMORE WASHER-TOPLOAD
Model 11015862400
Near Puyallup, WA 98371
Cameron M.
Job Details:
11/10/2021
Customer concern is that washer makes bang noise at beginning and end of spin cycle. Cycle tested unit 10x. Found no mechanical issues at this time. Advised customer on regular cleaning intervals. Also advised customer on using high quality detergent for best wash results.
We serviced a
GE DISHWASHER
Model PDW7880N00SS
Near Irving, TX 75063
Jacob P.
Job Details:
11/10/2021
"Customer concern of unit not draining. Found debris in air gap causing no drain. Removed debris. Test cycled, all checks ok."
We serviced a
WHIRLPOOL RANGE
Model WFG505M0BS3
Near Dallas, TX 75235
Jacob P.
Job Details:
11/09/2021
"Installed previously ordered burner body and cap. Test cycled, all checks ok."
We serviced a
KENMORE WASHER-FRONT LOA
Model 11025132412
Near Orting, WA 98360
Branden W.
Job Details:
11/09/2021
Customer concern is that washer will not operate properly on normal cycle. Found F7 E6 (motor) error stored. Found shift actuator arm came out of clutch causing washer to be stuck in spin configuration causing issues. Reinstalled actuator arm and secured. Cycle tested. All checks good.
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB835DW3
Near Puyallup, WA 98374
Branden W.
Job Details:
11/09/2021
Customer concern is that washer dispenser is rusting. Sounds like coins under tub. And washer was not working properly. Advised dispenser is not rusting but it has fabric softener and debris build up that looks like rust. Advised to clean dispenser and tracks. Found nails in drain pump causing noise. Cleaned pump. Advised to check pockets to prevent further issues. Unable to get washer to not operate properly at this time. All checks ok.
We serviced a
SAMSUNG DISHWASHER
Model DW80R5060US/AA 00
Near Puyallup, WA 98374
Branden W.
Job Details:
11/09/2021
"Customer concern is that dishwasher does not run a cycle and produces OC (overfill) error. Cycle tested rinse x2, express, normal and heavy cycles. Unable to get unit to fail on any cycle. Advised to call if issue returns."
We serviced a
SAMSUNG WASHER-FRONT LOA
Model WF350ANW/XAA 02
Near Spanaway, WA 98387
Branden W.
Job Details:
11/09/2021
Customer concern is that washer smells even after using washer cleaner. Ran entire quick wash cycle. No mechanical issues found. Advised to use afresh washer cleaner with triple dosage numerous times back to back to help eliminate smell.
We serviced a
LG RANGE
Model LRE3061ST/00
Near Irving, TX 75038
Jacob P.
Job Details:
11/09/2021
"Customer concern of broil not working. Found burnt wire to element causing no heat. Replaced connector. Test cycled, all checks ok."
We serviced a
SAMSUNG WASHER-FRONT LOA
Model WF42H5400AW/A2
Near Dallas, TX 75206
Jacob P.
Job Details:
11/08/2021
"Customer concern of unit leaking. Checked all internal and external hoses, pumps and valves. Unable to verify leak. Advised customer of keeping door glass and door boot clean. Unit functioning as designed at time of service."
We serviced a
ROPER WALL OVEN
Model 1053B2A
Near Tacoma, WA 98444
Branden W.
Job Details:
11/08/2021
"Arrived to repair oven, AHS also sent customer a new oven. Advised we do not install appliances. No work done. Advised customer to call AHS."
We serviced a
SAMSUNG WASHER-FRONT LOA
Model WF45N5300AF
Near Graham, WA 98338
Cameron M.
Job Details:
11/08/2021
"Customer concern is that washer leaks a lot intermittently does not matter load size or cycle settings. During cycle testing, found unit heavily oversuded. Also found unit leaking from rear tub vent , due to oversuds conditions. Also found drain hose inserted into wall to far, corrected and anchored drain hose. Found no other sorce of leak. Advised customer on regular cleaning cycle intervals. Also advised customer on using high quality detergent for best wash results."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV350AEW/XAA 03
Near Puyallup, WA 98375
Branden W.
Job Details:
11/08/2021
Customer concern is that dryer does not start a cycle. Found open thermal fuse. Found no heating component failures. Replaced fuse. Cycle tested all temperature setting. All checks good. ; used 1 DC47-00016A (THERMAL FUSE) from stock
We serviced a
WHIRLPOOL WALL OVEN
Model RBD307PVS00
Near Frisco, TX 75033
Jacob P.
Job Details:
11/08/2021
"Installed repaired control board, unit still doesn't turn on. Tested voltage into control board, checks ok. Called Ahs, ahs advised unit is being put into replacement options."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB955FW0
Near Graham, WA 98338
Branden W.
Job Details:
11/08/2021
Installed new control and drain pump. Cycle tested. All checks good.
We serviced a
KITCHENAID DISHWASHER
Model KDTE204ESS3
Near Rockwall, TX 75032
Jacob P.
Job Details:
11/08/2021
"Installed previously ordered heating element. Test cycled, all checks ok."
We serviced a
ELECTROLUX DISHWASHER
Model EW24ID80QS3A
Near Rockwall, TX 75087
Jacob P.
Job Details:
11/05/2021
"Customer concern of unit making loud noise and 30i error (leak error). Found power turned off to make upon arrival. Customer turned power on and found garbage disposal also on. Turned garbage disposal off. Found signs of water in base of unit. Test cycled ?3, no signs of leak. Unable to verify complaint, unit functioning as designed at time of service."
We serviced a
KENMORE WASHER-TOPLOAD
Model 11016962501
Near McKinney, TX 75070
Jacob P.
Job Details:
11/05/2021
"Customer concern of unit leaving streaks on clothes. Checked felt seal and other components, all checks ok. Advised customer that markings are more than likely coming from washer. Dryer functioning as designed."
We serviced a
MAYTAG DRYER-ELECTRIC
Model MEDC465HW0
Near Lakewood, WA 98498
Branden W.
Job Details:
11/05/2021
Customer concern is that dryer does not start. Found open thermal fuse causing dryer to not start. Found crushed vent caused dryer to overheat and trip thermal fuse. Replaced fuse. Shortened dryer vent. Advised to not push dryer back any further as it will crush vent. ; used 1 WP3392519 (FUSE-THRML) from stock
We serviced a
KENMORE DRYER-ELECTRIC
Model 41781100003
Near Enumclaw, WA 98022
Cameron M.
Job Details:
11/05/2021
"Installed previously ordered thermistor, exhaust thermistor, and control board. Cycle tested unit, all checks good"
We serviced a
WHIRLPOOL RANGE
Model WFE535S0JZ0
Near Puyallup, WA 98372
Branden W.
Job Details:
11/05/2021
Installed new infinite switches. Cycle tested. All checks good.
We serviced a
GE LAUNDRY CENTER
Model GUD27ESSJ1WW
Near Dallas, TX 75218
Jacob P.
Job Details:
11/05/2021
"Installed previously ordered suspension rods. Test cycled, all checks ok. Advised customer unit requires larger loads to spin out evenly."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV42H5000EW/A3 04
Near Buckley, WA 98321
Cameron M.
Job Details:
11/05/2021
Customer concern is that dryer makes noise during operation. Cycle tested unit 10x empty and with customer provided load. Found no mechanical problems at this time. Unit operating as designed.
We serviced a
SAMSUNG RANGE
Model FE-R300SX/XAA
Near Puyallup, WA 98373
Branden W.
Job Details:
11/05/2021
Installed new main PCB and infinite switch. Cycle tested. All checks good.
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWX655DW2
Near Graham, WA 98338
Branden W.
Job Details:
11/05/2021
Customer concern is that washer stops mid cycle and does not spin properly. Found F8 E1 (long fill) error stored. Found cold water inlet screen clogged with sediment causing almost no water to enter washer on cold fill. Cleaned inlet screen. Cycle tested with load. Found no issues with spin. All checks ok.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAHZ0
Near Gig Harbor, WA 98335
Branden W.
Job Details:
11/05/2021
Customer concern is that dishwasher is not cleaning well and has suds in it. Cycle tested dishwasher. Found partially clogged spray arm causing poor rotation. Cleaned spray arm. Did not find excessive suds. Advised that incoming water is 115 should be 120 minimum. Also advised to try Finish quantum detergent. Found no mechanical issues with dishwasher.
We serviced a
KENMORE DISHWASHER
Model 66513293K110
Near Enumclaw, WA 98022
Branden W.
Job Details:
11/04/2021
Installed new wash pump and grommet. Cycle tested. All checks good.
We serviced a
FRIGIDAIRE DISHWASHER
Model FGID2476SF4A
Near Wylie, TX 75098
Jacob P.
Job Details:
11/04/2021
"Installed previously ordered manifold, bearing and dispenser. Test cycled, all checks ok."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT910SAYM1
Near Tacoma, WA 98443
Cameron M.
Job Details:
11/04/2021
"Installed previously ordered sump assembly, cycle tested unit. All checks good."
We serviced a
LG RANGE
Model LRE3061BD/00
Near Rowlett, TX 75088
Jacob P.
Job Details:
11/04/2021
"Customer concern of broil element not working. Found burnt connector on element causing no power. Replaced connector. Test cycled, all checks ok."
We serviced a
KITCHENAID DISHWASHER
Model 66513963K010
Near Dallas, TX 75218
Jacob P.
Job Details:
11/04/2021
"Installed previously ordered control board, inlet valve and console. Test cycled, all checks ok."
We serviced a
LG WASHER-FRONT LOA
Model WM4270HWA/01
Near Tacoma, WA 98466
Cameron M.
Job Details:
11/04/2021
"Customer concern is that washer leaks approximately 4cups of water during operation. Found dirt buildup on door glass ,causing leak. Also found active oversuds condition, causing water to come out rear vent. Advised customer on regular cleaning intervals. Also advised customer on using high quality detergent for best wash results."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB865GW0
Near Dallas, TX 75228
Jacob P.
Job Details:
11/04/2021
"Installed previously ordered drain pump. Test cycled, all checks ok."
We serviced a
WHIRLPOOL DISHWASHER
Model GU3600XTVQ2
Near Dallas, TX 75227
Jacob P.
Job Details:
11/04/2021
"Installed previously ordered sump assembly. Test cycled, all checks ok."
We serviced a
KITCHENAID DISHWASHER
Model KDTM404ESS3
Near Puyallup, WA 98374
Branden W.
Job Details:
11/04/2021
Customer concern is that dishwasher toe panel is bent and hitting door. Straightened panel. Reinstalled. All checks good.
We serviced a
SAMSUNG WASHER-FRONT LOA
Model WF45N5300AV/US
Near Puyallup, WA 98373
Cameron M.
Job Details:
11/03/2021
"Installed previously ordered door boot, boot clamp and drain pump. Cycle tested unit, all checks good"
We serviced a
SAMSUNG DISHWASHER
Model DW80J3020US/AA
Near Fife, WA 98424
Branden W.
Job Details:
11/03/2021
Installed new door latch. Cycle tested. All checks good.
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV42H5000EW/A3 01
Near Tacoma, WA 98405
Branden W.
Job Details:
11/03/2021
Customer concern is that dryer was making noise. Now does not operate. Found failed idler pulley causing noise and dryer to not start. Replaced pulley. Cycle tested. All checks good. ; used 1 DC93-00634A (IDLER ASSEMBLY) from stock
We serviced a
LG WASHER-FRONT LOA
Model WM3470HVA
Near Tacoma, WA 98404
Branden W.
Job Details:
11/03/2021
Installed new board and console. Cycle tested. All checks good.
We serviced a
KITCHENAID DISHWASHER
Model KUDC10FXSS6
Near Dallas, TX 75218
Jacob P.
Job Details:
11/03/2021
"Installed previously ordered door seal. Test cycled, all checks ok."
We serviced a
LG RANGE
Model LRE30755ST
Near Dallas, TX 75218
Jacob P.
Job Details:
11/03/2021
"Installed previously ordered surface element. Test cycled, all checks ok."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB755DW1
Near Spanaway, WA 98387
Cameron M.
Job Details:
11/03/2021
"Installed previously ordered transmission,stator, rotor, clutch and slider. Calibrated unit. Unable to fully test unit, as it's in garage not hooked up to utilities. Tested unit via garden hose, preformed drain and spin. Unit operating as designed."
We serviced a
SAMSUNG WASHER-FRONT LOA
Model WF45R6100AC/US
Near Milton, WA 98354
Cameron M.
Job Details:
11/03/2021
"Installed previously ordered drain pump assembly. Cycle tested unit, all checks good."
We serviced a
LG WASHER-TOPLOAD
Model WT7300CV
Near McKinney, TX 75070
Jacob P.
Job Details:
11/03/2021
"Customer concern of unit taking too long to finish. Found drain hose too far in wall causing siphon and unit unlevel causing out of balance. Secured drain hose at proper depth and leveled machine. Test cycled, all checks ok."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT910SAYM1
Near Frisco, TX 75035
Jacob P.
Job Details:
11/03/2021
"Installed previously ordered sump assembly. Test cycled, all checks ok. Left failed part with customer."
We serviced a
WHIRLPOOL WASHER-FRONT LOA
Model WFW8300SW01
Near Dallas, TX 75220
Jacob P.
Job Details:
11/02/2021
"Installed previously ordered shocks. Test cycled, all checks ok."
We serviced a
SAMSUNG DISHWASHER
Model DW80K5050US/AA 03
Near Tacoma, WA 98406
Branden W.
Job Details:
11/02/2021
Installed new case brake and pump. Cycle tested. All checks good.
We serviced a
GE RANGE
Model JGP336WEV4WW
Near Plano, TX 75024
Jacob P.
Job Details:
11/02/2021
"Installed previously ordered igniter switches. Test cycled, all checks ok."
We serviced a
KENMORE WASHER-TOPLOAD
Model 11044832200
Near Enumclaw, WA 98022
Cameron M.
Job Details:
11/02/2021
"Customer concern is that washer does not drain and produces sud error code. Found debris in drain pump clean out, causing unit to not drain and spin. Cleaned out drain pump. Cycle tested unit, all checks good. Advised customer on regular cleaning intervals for optimal operation of washer."
We serviced a
MAYTAG DISHWASHER
Model MDBH950AWB
Near Puyallup, WA 98375
Branden W.
Job Details:
11/02/2021
Customer concern is that dishwasher leaked from bottom. Cycle tested numerous times. Unable to get unit to leak at this time. Advised to monitor and call if issue returns.
We serviced a
SAMSUNG WASHER-FRONT LOA
Model WF45K6500AV/A2 11
Near Gig Harbor, WA 98332
Branden W.
Job Details:
11/02/2021
Installed new inverter board and stator. Calibrated. Cycle tested with load of towels. All checks good.
We serviced a
MAYTAG WASHER-FRONT LOA
Model MHW5630HC0
Near Spanaway, WA 98387
Cameron M.
Job Details:
11/02/2021
"Installed previously ordered door boot. Cycle tested unit, all checks good. Customer declined to retain leaking part."
We serviced a
KITCHENAID DISHWASHER
Model KDTM704KPS0
Near Allen, TX 75013
Jacob P.
Job Details:
11/02/2021
"Installed previously ordered heating element. Test cycled, all checks ok. Left failed part with customer."
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW7500GW0
Near Tacoma, WA 98405
Cameron M.
Job Details:
11/02/2021
"Customer concern is that washer does not start cycle,spin. Found f0e3 (overload), f5e1(lid switch fault),f8e6(water hazard). Cycle tested lid lock 20x found lock failed to re-engage 1 out every five attempts. Needs new lid lock. Installed new lid lock. Cycle tested lid lock, and Cycle tested unit all checks good. Advised customer on regular cleaning intervals for optimal performance. Also advised customer on using high quality detergent for best wash results. ; used 1 W10810403 (LID LOCK ASSY) from stock"
We serviced a
GE DISHWASHER
Model GSD2300N00BB
Near McKinney, TX 75071
Jacob P.
Job Details:
11/02/2021
"Installed previously ordered wash motor. Test cycled, all checks ok."
We serviced a
WHIRLPOOL RANGE
Model WFE770H0FZ2
Near Garland, TX 75043
Jacob P.
Job Details:
11/02/2021
"Installed previously ordered infinite switch. Test cycled, all checks ok."
We serviced a
GE WASHER-TOPLOAD
Model WBSE2090A2WW
Near Garland, TX 75041
Jacob P.
Job Details:
11/02/2021
"Installed previously ordered inlet valve. Test cycled, all checks ok."
We serviced a
GE WASHER-FRONT LOA
Model GFW850SPN0DG
Near Bonney Lake, WA 98391
Branden W.
Job Details:
11/02/2021
Customer concern is that washer leaks small amount. Found 2 leaks. One from door boot annmd door glass and another from dispenser. Cleaned and reseated dispenser hose and clamp. Cleaned door glass. Cycle tested several times. No leaks. Advised to keep door glass clean.
We serviced a
GE WASHER-TOPLOAD
Model GTWN4250D1WS
Near Irving, TX 75063
Jacob P.
Job Details:
11/01/2021
"Installed previously ordered inlet valve. Test cycled, all checks ok."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE60M9900V/A3
Near University Place, WA 98466
Cameron M.
Job Details:
11/01/2021
Installed previously ordered door switch. Cycle tested unit. All checks good. Preformed airflow test failed (red). Advised customer dryer vent duct needs to be cleaned asap and use cannot resume until completed.
We serviced a
GE WALL OVEN
Model JK5000SFSS
Near Grand Prairie, TX 75051
Jacob P.
Job Details:
11/01/2021
"Unable to locate customers home. Called customer, incorrect address was provided. Customer lives outside our service area. Sending call back to Lowes."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE54R7600C/A3
Near DuPont, WA 98327
Branden W.
Job Details:
11/01/2021
Customer concern is that dryer power terminal is burned. Replaced terminal block and wire. Installed customer provided power cord. Cycle tested. All checks ok.
We serviced a
KENMORE DRYER - ELECTRIC
Model DV42H5000EW/A3
Near Edgewood, WA 98372
Cameron M.
Job Details:
11/01/2021
"Customer concern is that dryer powers but does not start cycle. Found broken belt and seized idler pulley causing unit to power but not start cycle. Installed new belt and idler pulley. Cycle tested unit, all checks good. ; used 1 661570V (BELT), and 1 279640 (PULLEY,IDLER) from stock"
We serviced a
KENMORE WASHER-FRONT LOA
Model 79640518900
Near Gig Harbor, WA 98335
Branden W.
Job Details:
11/01/2021
Customer concern is that washer will not drain. Found failed drain pump causing unit to not drain. Replaced pump. Cycle tested. All checks good. ; used 1 4681EA2001T (DRAIN PUMP) from stock
We serviced a
WHIRLPOOL RANGE
Model WFE550S0HZ1
Near Tacoma, WA 98409
Cameron M.
Job Details:
11/01/2021
"Installed previously ordered door hinges. Cycle tested unit, all checks good."
We serviced a
GE DRYER-ELECTRIC
Model GFD45ESPM1DG
Near Buckley, WA 98321
Cameron M.
Job Details:
11/01/2021
"Installed previously ordered control panel, upper drum bearing, felt liner, bearing glides. Cycle tested unit, all checks good. Advised customer dryer vent hose needs to be shortened to allow sufficient airflow."
We serviced a
SAMSUNG WASHER-FRONT LOA
Model WF210ANW/XAA
Near Irving, TX 75063
Jacob P.
Job Details:
11/01/2021
"Installed previously ordered drain pump. Test cycled, all checks ok."
We serviced a
KENMORE WASHER-TOPLOAD
Model 11026132413
Near Tacoma, WA 98418
Branden W.
Job Details:
11/01/2021
Installed lid lock. Cycle tested. All checks ok.
We serviced a
SAMSUNG WASHER-FRONT LOA
Model WF42H5200AW/A2 01
Near Orting, WA 98360
Cameron M.
Job Details:
11/01/2021
"Installed sears provided drain pump. Cycle tested unit 3x, all checks good."
We serviced a
FRIGIDAIRE DISHWASHER
Model FGIP2468UF2A
Near Graham, WA 98338
Branden W.
Job Details:
11/01/2021
Customer concern is that spray arm melted on heater element. Found extra spray arm in dishwasher from factory. Cleaned plastic from element. Cycle tested. All checks ok. Advised spray arm was extra and should not have been in dishwasher.
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model LER4634JQ1
Near University Place, WA 98467
Cameron M.
Job Details:
10/29/2021
"Customer concern is that dryer does not heat. Preformed airflow test failed (yellow ).found corroded and broken wire connection to element and high limit, causing unit to run but not heat. Needs new high limit and wire spade. Installed wire spade to element and Installed new high limit and wire terminal. Cycle tested unit. All checks good. ; used 1 WP3977767 (THRMST-FIX), and 1 279457 (WIRE-SPADE) from stock"
We serviced a
KENMORE LAUNDRY CENTER
Model 41799570110
Near Tacoma, WA 98406
Cameron M.
Job Details:
10/29/2021
"Customer concern is that dryer powers but does not tumble. Found broken belt,causing dryer to power and not tumble. Needs new belt. Installed new belt. Cycle tested all checks good. Preformed airflow test failed (red). Advised customer dryer vent needs to be cleaned. ; used 1 134503600 (BELT) from stock"
We serviced a
KENMORE WASHER-TOPLOAD
Model 11028802890
Near Rowlett, TX 75089
Jacob P.
Job Details:
10/29/2021
"Installed previously ordered transmission and clutch. Found tear in tub to pump hose. Replaced hose. Test cycled, all checks ok. ; used 1 285871 (HOSE,TUB TO PUMP) from stock"
We serviced a
FRIGIDAIRE DISHWASHER
Model FFCD2413US4A
Near Plano, TX 75094
Jacob P.
Job Details:
10/29/2021
"Customer concern of unit not draining. Found plastic plug still in garbage disposal. Removed plug. Test cycled, all checks ok."
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model WED7000DW0
Near Spanaway, WA 98387
Branden W.
Job Details:
10/29/2021
"Customer concern is that dryer makes noise. Found worn drum roller causing noise. Replaced rollers. Vacuumed inside of dryer. Cycle tested. All checks good. ; used 1 349241T (SUPPORT,ROLLER (2 PACK)) from stock"
We serviced a
KENMORE WASHER-TOPLOAD
Model 79640518900
Near McKinney, TX 75070
Jacob P.
Job Details:
10/29/2021
"Installed previously ordered drain pump. Test cycled, all checks ok."
We serviced a
GE DISHWASHER
Model GDF520PGJ2BB
Near Lakewood, WA 98499
Branden W.
Job Details:
10/28/2021
Installed new main control. Cycle tested. All checks good.
We serviced a
KENMORE DRYER-ELECTRIC
Model 41781122310
Near Puyallup, WA 98372
Branden W.
Job Details:
10/28/2021
Customer concern is that dryer makes squealing noise. Took unit apart. Found idler pulley sticking. Cleaned and lubed pulley. All mechanical components check good. Cycle tested. All checks good.
We serviced a
KENMORE WASHER-TOPLOAD
Model 79631523211
Near Dallas, TX 75218
Jacob P.
Job Details:
10/28/2021
"Installed previously ordered drain pump. Test cycled, all checks ok."
We serviced a
GE WASHER-TOPLOAD
Model GTW465ASN0WW
Near Frisco, TX 75035
Jacob P.
Job Details:
10/28/2021
"Customer concern of unit making clicking sound. Found debris between tub and basket causing sound. Dislodged debris. Test cycled, all checks ok."
We serviced a
KITCHENAID RANGE
Model ksgg700ess0
Near Dallas, TX 75220
Jacob P.
Job Details:
10/28/2021
"Installed previously ordered bezels. Test cycled, all checks ok."
We serviced a
FRIGIDAIRE DRYER-ELECTRIC
Model FER641FS0
Near Grand Prairie, TX 75050
Jacob P.
Job Details:
10/28/2021
"Installed previously ordered light bulb. Test cycled, all checks ok."
We serviced a
MAYTAG RANGE
Model MGR6875ADS
Near Lakewood, WA 98498
Branden W.
Job Details:
10/28/2021
Customer concern is that front right burner does not have much flame. Found clogged orifice causing poor gas flow. Cleaned orifice. Cycle tested. All checks good.
We serviced a
KENMORE WASHER-TOPLOAD
Model 11022352510
Near Lakewood, WA 98499
Branden W.
Job Details:
10/28/2021
No work order in servicelive. No work done.
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV365ETBGWR/A3
Near Forney, TX 75126
Jacob P.
Job Details:
10/27/2021
"Customer concern of unit not heating. Found burnt connector to heating element causing no heat. Replaced connector. Test cycled, all checks ok."
We serviced a
LG DRYER-ELECTRIC
Model DLEX7700VE
Near Gig Harbor, WA 98335
Cameron M.
Job Details:
10/27/2021
"Installed previously ordered main pcb and door switch. Cycle tested unit, all checks good."
We serviced a
WHIRLPOOL WASHER-FRONT LOA
Model GHW9150PW0
Near Dallas, TX 75230
Jacob P.
Job Details:
10/27/2021
"Installed previously ordered inlet valve. Test cycled, all checks ok."