Service History 131 - RPS Appliance Repair

We serviced a

WHIRLPOOL WASHER-TOPLOAD

Model WTW5500XW0

Near Puyallup, WA 98374

Branden W.

Job Details: 08/13/2021

Installed new inlet housing assembly. Cycle tested. All checks good.

We serviced a

WHIRLPOOL WASHER-TOPLOAD

Model WTW5105HW0

Near Graham, WA 98338

Branden W.

Job Details: 08/13/2021

Customer concern is that washer will intermittently trip circuit breaker. Cycle tested washer through various cycles with and without a load. Ran full amp load test. Only drawing max amps of 7.6 while under full power draw. No heater on this model. Found no wiring issues. Found no issues with washer at this time. Advised to have electrician check breaker for possible premature tripping.

We serviced a

SAMSUNG WASHER-TOPLOAD

Model WA50R5400AV/US 03

Near Spanaway, WA 98387

Branden W.

Job Details: 08/13/2021

"Customer concern is that washer will leak when deep fill is selected. Cycle tested empty and with a load in heavy duty, quick wash and rinse and spin with deep fill option on. Unable to reproduce issue at this time. Advised to monitor and call if issue returns. Also advised water heater leaking. Collected 75.00 deductible via card."

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWB835DW4

Near Puyallup, WA 98374

Branden W.

Job Details: 08/13/2021

Customer concern is that washer did not spin properly on last use. Retrieved F0 E4 (water temp too high for final spin) and F0 E3 (overloaded) found water hoses reversed causing hot water in final rinse causing F0 E4 error. Reversed fill hoses at wall. Cycle tested empty and with customer provided load. Found no mechanical issues with washer. Advised about overloading and out of balance condition.

We serviced a

WHIRLPOOL WASHER-TOPLOAD

Model WTW5000DW2

Near Farmers Branch, TX 75234

Jacob P.

Job Details: 08/13/2021

"Customer concern of unit not completing cycle. Found long fill error stored. Found debris in cold water inlet screen causing long fill. Cleaned debris. Test cycled, all checks ok."

We serviced a

FRIGIDAIRE RANGE

Model LGEF3043KFF

Near Dallas, TX 75225

Jacob P.

Job Details: 08/13/2021

"Installed previously ordered surface element. Test cycled, all checks ok."

We serviced a

KENMORE DRYER-ELECTRIC

Model 110.696228

Near Spanaway, WA 98387

Cameron M.

Job Details: 08/13/2021

"Customer concern is that dryer does not start cycle. Found open thermal fuse and failed operating thermostat. Needs new thermal fuse and operating thermostat. Preformed airflow test failed (red), preformed temperature checks, in range. Advised customer DO NOT USE DRYER, UNTIL DRYER DUCT IS CLEANED. ; used 1 WP3387134 (THRMST-FIX), and 1 WP3392519 (FUSE-THRML) from stock"

We serviced a

KENMORE WASHER-TOPLOAD

Model 11022352511

Near Dallas, TX 75243

Jacob P.

Job Details: 08/13/2021

"Performed pm check on washer, all checks ok."

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV331AEW/XAA

Near Irving, TX 75063

Jacob P.

Job Details: 08/13/2021

"Customer concern of vent detached from back of dryer. Secured vent to dryer. Test cycled, all checks ok."

We serviced a

SAMSUNG WASHER-TOPLOAD

Model WA40J3000AW/AA

Near Puyallup, WA 98375

Branden W.

Job Details: 08/13/2021

Customer concern is that washer has debris in it. Unable to remove washplate for cleaning without damage. Drain hose at proper depth in wall drain. Advised to run clean cycle regularly to eliminate any build up.

We serviced a

MAYTAG WASHER-FRONT LOA

Model MHW5100DW0

Near Dallas, TX 75252

Jacob P.

Job Details: 08/13/2021

"Customer concern of unit not powering on. Found power shut off to unit. Turned power on. Ran unit through automatic diagnostic test, all checks ok."

We serviced a

GE WASHER-TOPLOAD

Model GTW685BSL1WS

Near Murphy, TX 75094

Jacob P.

Job Details: 08/12/2021

"Installed previously ordered inlet valve. Test cycled, all checks ok."

We serviced a

LG WASHER-TOPLOAD

Model WT1201CV

Near McKinney, TX 75071

Jacob P.

Job Details: 08/12/2021

"Customer concern of unit leaking. Found drain hose too far out of wall causing unit to drain onto floor. Secured drain hose at proper depth. Test cycled, all checks ok."

We serviced a

GE DISHWASHER

Model GDF645SGN3WW

Near Forney, TX 75126

Jacob P.

Job Details: 08/12/2021

"Customer concern of unit not heating. Found wire to heating element unplugged causing no heat. Plugged heating element in. Test cycled, all checks ok."

We serviced a

LG DRYER-ELECTRIC

Model DLE7177RM

Near Puyallup, WA 98373

Cameron M.

Job Details: 08/12/2021

"Customer concern is that dryer does not heat. Preformed airflow test failed (red). Found open high-limit, causing unit to not heat. Needs new high limit. Installed new high limit. Preformed temperature checks with vent off , in range . All checks good. Advised customer dryer duct needs to be cleaned asap, before regular usage continues to prevent further issues. ; used 1 6931EL3003D (THERMOSTAT) from stock"

We serviced a

SAMSUNG DISHWASHERS

Model DW80J3020US/AA

Near Puyallup, WA 98375

Branden W.

Job Details: 08/12/2021

Customer concern is that dishwasher is not mounted and top rack falls down. Recounted dishwasher and reinstalled upper rack on track. All checks good.

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV50K8600EV/43 01

Near Puyallup, WA 98373

Branden W.

Job Details: 08/12/2021

"Customer concern is that dryer does not start. Found failed idler pulley caused belt to come off causing unit to not start. Also found failed drum roller. Replaced idler pulley and roller. Vacuumed inside of dryer. Cycle tested. All checks ok. ; used 1 DC97-16782A (DRUM ROLLER), and 1 DC93-00634A (IDLER ASSEMBLY) from stock"

We serviced a

SAMSUNG WASHER-TOPLOAD

Model WA50M7450AW/A4

Near Buckley, WA 98321

Cameron M.

Job Details: 08/12/2021

"Customer concern is that washer is from bottom of unit and will repeatedly fill and go out of balance. Cycle tested unit 3x empty on quick wash. Cycle tested unit with customer provided load of towels. Was unable to duplicate customer concern, Advised customer to monitor and call if issue persists."

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model WED5600XW0

Near Lakewood, WA 98498

Branden W.

Job Details: 08/12/2021

Customer concern is that dryer takes multiple cycles to dry. Found lint screen housing clogged with lint. Vacuumed inside of dryer and housing. Performed airflow test. Test failed (yellow) advised to have duct from floor to outside cleaned. Cycle tested temperatures. Temps in range at 175 on high. Cleaned and calibrated moisture sensors. Dryer operating as designed.

We serviced a

GE DRYER-ELECTRIC

Model GTD45EASJ2WS

Near Garland, TX 75040

Jacob P.

Job Details: 08/12/2021

"Customer concern that unit made loud noise when starting dryer. Started dryer, no noise. Checked for debris in glide bearing, all clear. Removed debris from under baffles. Leveled unit. Test cycled again, unable to replicate issue. Unit functioning as designed at time of service."

We serviced a

GE WASHER-TOPLOAD

Model GTW335ASN1WW

Near Garland, TX 75040

Jacob P.

Job Details: 08/12/2021

"Customer concern of unit making grinding noise at end of cycle. Test cycled unit, unable to replicate issue. Cleaned oil and debris from pulley. Test cycled drain pump, clutch transmission and motor, all checks ok. Leveled unit. Unit functioning as designed at time of service."

We serviced a

KENMORE WASHER-TOPLOAD

Model 11028902790

Near Garland, TX 75040

Jacob P.

Job Details: 08/12/2021

"Customer concern of unit not draining or spinning. Found broken lid switch causing no drain or spin. Replaced lid switch. Test cycled, all checks ok. ; used 1 WP3949238 (SWITCH-LID) from stock"

We serviced a

WHIRLPOOL LAUNDRY CENTER

Model LTE5243DQ6

Near Tacoma, WA 98409

Cameron M.

Job Details: 08/12/2021

"Installed previously ordered timer. Cycle tested unit, all checks good."

We serviced a

KITCHENAID DISHWASHER

Model KUDS35FXSS5

Near Graham, WA 98338

Branden W.

Job Details: 08/12/2021

"Customer concern is that dishwasher leaks a lot of water from both sides of door. Found lower spray arm and housing allowing pressurized water to leak at support causing water wave towards door causing leak. Needs new spray arm, support, seal and cap. Declined to repair at this time."

We serviced a

SAMSUNG DISHWASHER

Model DW80R2031USAA 00

Near Puyallup, WA 98371

Cameron M.

Job Details: 08/12/2021

"Customer concern is that dishwasher start leaking around front corners of unit , now unit alarms and does not start cycle. Cycle tested unit 15x was unable to duplicate customer concern. Advised customer to monitor and call if issue persists."

We serviced a

LG WASHER-TOPLOAD

Model WT7700HVA/01

Near Gig Harbor, WA 98335

Cameron M.

Job Details: 08/11/2021

"Customer concern is that washer top is starting to rust and corrode around bleach dispenser and inner lip on washer top at seam between case and water top. Found rust surrounding bleach dispenser. Causing powder coat to bubble and peal around dispenser. Needs new cover.Called Lowes repair support for Auth, Lowes declined repair due to being outside of three years of purchase date."

We serviced a

GE WASHER-FRONT LOA

Model GFW550SSN0WW

Near Dallas, TX 75248

Jacob P.

Job Details: 08/11/2021

"Customer concern of unit tearing clothes. Found debris stuck in basket lip snagging clothes. Removed debris. Test cycled, all checks ok."

We serviced a

FRIGIDAIRE RANGE

Model FPGH3077RFE

Near Dallas, TX 75244

Jacob P.

Job Details: 08/11/2021

"Installed previously ordered relay board and UI board. Test cycled, all checks ok."

We serviced a

MAYTAG WASHER-FRONT LOA

Model MHW3505FW0

Near Fircrest, WA 98466

Cameron M.

Job Details: 08/11/2021

"Customer concern is that washer started leaking from rear left corner after preforming self clean cycle. Found evidence of over suds condition, causing unit to leak. Cycle tested unit 3x found no mechanical issues. Unit operating as designed. Advised customer on regular clean cycle intervals ."

We serviced a

MAYTAG DRYER-ELECTRIC

Model MEDX655DW1

Near Puyallup, WA 98373

Cameron M.

Job Details: 08/11/2021

Customer concern is that dryer takes multiple cycles to dry clothes. Preformed airflow test passed (green). Preformed temperature checks in range. Cleaned and calibrated moisture sensors. Found no mechanical issues at time of service. Unit operating as designed.

We serviced a

GE RANGE

Model JB860SJ3SS

Near Puyallup, WA 98373

Branden W.

Job Details: 08/11/2021

"Customer concern is that after power cycle at breaker, range does not operate any elements. Found only 120vac supplied to range at wall plug. Reset breaker for range several times. Still only 120v. Advised an electrician is needed to restore 240v to range."

We serviced a

FRIGIDAIRE DISHWASHER

Model FPHD2485NF1A

Near McKinney, TX 75071

Jacob P.

Job Details: 08/11/2021

"Customer concern of unit not starting. Advised customer door must be open to select and start cycles. Instructed customer on proper operation of machine, all checks ok."

We serviced a

LG DISHWASHER

Model LDT5678ST

Near Tacoma, WA 98408

Branden W.

Job Details: 08/11/2021

Installed new door latch. Cycle tested. All checks good.

We serviced a

MAYTAG DRYER-ELECTRIC

Model MEDB835DW4

Near Dallas, TX 75217

Jacob P.

Job Details: 08/11/2021

"Customer concern of dryer making squealing noise. Found seized idler pulley causing noise. Replaced idler pulley. Test cycled, all checks ok. ; used 1 279640 (PULLEY,IDLER) from stock"

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model WED9200SQ0

Near Puyallup, WA 98375

Branden W.

Job Details: 08/10/2021

Customer concern is that dryer does not heat. Found burnt wire and terminal at elememt causing no heat. Replaced wire and terminal. Cycle tested. Good Temps. ; used 1 279457 (WIRE-SPADE) from stock

We serviced a

GE DISHWASHER

Model GDT605PSM5SS

Near Plano, TX 75024

Jacob P.

Job Details: 08/10/2021

"Customer concern of door not latching. Found latch misaligned causing door to not close. Realigned latch. Test cycled, all checks ok."

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model WED7990FW0

Near Tacoma, WA 98403

Branden W.

Job Details: 08/10/2021

Customer concern is that dryer takes multiple cycles to dry. F4 E4 (L2 line voltage low) F3 E6 (moisture sensor open) cycle tested through different cycles and service mode. Found control board only reading 75 volts on L2. Tested at wall. 120v on L2 and L1. Tested and calibrated moisture sensors. Needs new CCU per whirlpool tech guide. Declined to repair

We serviced a

GE DISHWASHER

Model GSD3360K65SS

Near Lewisville, TX 75067

Jacob P.

Job Details: 08/10/2021

"Installed previously ordered solenoid and armature. Test cycled, all checks ok."

We serviced a

WHIRLPOOL DISHWASHER

Model WDF520PADM7

Near The Colony, TX 75056

Jacob P.

Job Details: 08/10/2021

"Installed previously ordered dispenser. Test cycled, all checks ok."

We serviced a

WHIRLPOOL WASHER-FRONT LOA

Model WFW9400SW02

Near Graham, WA 98338

Cameron M.

Job Details: 08/10/2021

"Customer concern is that washer produces f20 and f28 error codes ,unit has to be unplugged to reset. Found f20 (no water flow/pressure switch trip not detected) via service mode. Cleaned inlet screens of both hot and cold water valves. Cycle tested unit all checks good."

We serviced a

KENMORE WASHER-FRONT LOA

Model 11022342511

Near Coppell, TX 75019

Jacob P.

Job Details: 08/10/2021

"Installed previously ordered wash plate, agitator and dispenser cup. Test cycled, all checks ok."

We serviced a

KENMORE WASHER-TOPLOAD

Model 79631523211

Near Plano, TX 75074

Jacob P.

Job Details: 08/10/2021

"Installed previously ordered inlet valve and suspension rods. Test cycled, all checks ok."

We serviced a

KENMORE WALL OVEN

Model 79048733901

Near Dallas, TX 75248

Jacob P.

Job Details: 08/09/2021

"Performed pm check on wall oven, all checks ok."

We serviced a

LG RANGE

Model LSG4511ST 00

Near Milton, WA 98354

Branden W.

Job Details: 08/09/2021

Customer concern is that new range smells like gas. Tested all connections with electric sniffer and bubbles. Found no leaks. Advised that spent gas is normal smell when in use. Advised to always run ventilation fan from OTR microwave when using range. No issues found.

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DVE54M8750V/A3

Near Tacoma, WA 98407

Cameron M.

Job Details: 08/09/2021

"Installed sears supplied door seal , cycle tested unit, all checks good."

We serviced a

WHIRLPOOL WASHER-FRONT LOA

Model WFW5620HW2

Near Steilacoom, WA 98388

Cameron M.

Job Details: 08/09/2021

"Customer concern is that washer does not fill. Found loose connection at cold fill valve, cycle unit to not fill. Reseated connection, cycle tested all checks good."

We serviced a

FRIGIDAIRE DISHWASHER

Model FGHD2433KF1

Near Dallas, TX 75218

Jacob P.

Job Details: 08/09/2021

"Customer concern of unit not starting. Advised customer that door has to be open to select and start cycle. Test cycled all buttons and functions, all checks ok."

We serviced a

KENMORE DISHWASHER

Model 66516914001

Near Tacoma, WA 98408

Branden W.

Job Details: 08/09/2021

Customer concern is that dishwasher leaked. Cycle tested x2 through rinse and drain. Found no signs of leak under dishwasher. Unable to get unit to leak at this time. Advised to call if issue returns.

We serviced a

GE DISHWASHER

Model GDF610PMJ2ES

Near Graham, WA 98338

Branden W.

Job Details: 08/09/2021

Customer concern is that dishwasher does not start a cycle. Found dishwasher does not recognize door being closed causing it to not start. Found bad connection at main control causing issue. Reseated connection. Cycle tested numerous times. All checks good.

We serviced a

KENMORE DRYER-ELECTRIC

Model 11060222511

Near Garland, TX 75044

Jacob P.

Job Details: 08/09/2021

"Performed pm check on dryer, failed air flow test. Advised customer that vent from back of dryer to outside needs to be cleaned. Unit functioning as designed."

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWX655DW1

Near Dallas, TX 75243

Jacob P.

Job Details: 08/09/2021

"Performed pm check on washer, all checks ok."

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWB835DC

Near Spanaway, WA 98387

Cameron M.

Job Details: 08/09/2021

"Customer concern is that washer does not agitate, drain and spin. Cycle tested unit empty via service mode, found no mechanical issues. Cycle tested unit 3x with customer provided load of towels. Was unable to duplicate customer concern. Advised customer to monitor ,and call if issue persists."

We serviced a

FRIGIDAIRE DISHWASHER

Model FFCD2413US1A

Near Tacoma, WA 98444

Branden W.

Job Details: 08/09/2021

Customer concern is that dishwasher does not clean or dissolve detergent. Found water to dishwasher turned off causing unit to not wash. Turned water on. Cycle tested. Unit operating as designed.

We serviced a

MAYTAG DISHWASHER

Model MDB4949SDE2

Near Puyallup, WA 98374

Branden W.

Job Details: 08/09/2021

Installed new manifold. Cycle tested. All checks good.

We serviced a

SAMSUNG WASHER-TOPLOAD

Model WA54M8750AW/A4

Near Tacoma, WA 98466

Cameron M.

Job Details: 08/06/2021

"Installed previously ordered main harness, pcb display,mems sensor. Cycle tested unit 3x all checks good."

We serviced a

GE DISHWASHER

Model GDT535PSMSS

Near Irving, TX 75062

Jacob P.

Job Details: 08/06/2021

"Installed previously ordered console face plate. Test cycled, all checks ok."

We serviced a

SAMSUNG DISHWASHER

Model DW80J9945US/AA 01

Near Sachse, TX 75048

Jacob P.

Job Details: 08/06/2021

"Installed previously ordered base, water wall motor, dispenser and toe panel. Test cycled, all checks ok."

We serviced a

FRIGIDAIRE DISHWASHER

Model FGHD2465NF1A

Near Puyallup, WA 98374

Cameron M.

Job Details: 08/06/2021

"Installed previously ordered latch asm , bord. Cycle tested unit 3x all checks good"

We serviced a

SAMSUNG DISHWASHER

Model DW80F800UWS/AA 01

Near McKinney, TX 75071

Jacob P.

Job Details: 08/06/2021

"Customer concern of LE error (leak error). Found debris between sump seal and tub causing leak. Cleaned seal and tub. Test cycled, all checks ok."

We serviced a

WHIRLPOOL DRYER-GAS

Model WGD5500ST0

Near Farmers Branch, TX 75234

Jacob P.

Job Details: 08/06/2021

"Customer concern of unit not heating. Found coil valves not opening causing no heat. Replaced coil valves, test cycled, all checks ok. ; used 1 279834 (2 COIL GAS VALVE SET) from stock"

We serviced a

FRIGIDAIRE DISHWASHER

Model LFBD2409LF3C

Near Tacoma, WA 98409

Cameron M.

Job Details: 08/05/2021

Installed previously ordered lower door gasket. Cycle tested all checks good. Left part with customer as it caused a water leak.

We serviced a

LG WASHER-FRONT LOA

Model WM2655HVA

Near Tacoma, WA 98405

Branden W.

Job Details: 08/05/2021

"Customer concern is that washer leaks. Stacked set in closet with no access. Removed set, unstained. Found leaking hot water inlet valve causing leak. Replaced valve. Cycle tested x3. Installed customer provided inlet hoses. Reinstalled. All checks ok. ; used 1 5220FR2006H (INLET VALVE (HOT)) from stock"

We serviced a

KENMORE DRYER-GAS

Model 11067072600

Near Dallas, TX 75205

Jacob P.

Job Details: 08/05/2021

"Performed pm check on dryer, all checks ok."

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV45K6200EZ/A3 01

Near McKinney, TX 75070

Jacob P.

Job Details: 08/05/2021

"Customer concern of unit very noisy then stopped working. Found worn idler pulley causing no function. Replaced idler pulley. Test cycled, all checks ok. ; used 1 DC93-00634A (IDLER ASSEMBLY) from stock"

We serviced a

SAMSUNG COOKTOP

Model NZ30K7880UG/AA

Near Allen, TX 75002

Jacob P.

Job Details: 08/05/2021

"Customer concern of burning smell when using unit. Test cycled machine, no mechanical failure found. Called Samsung tech support. Per tech support, they do not recommend replacing any parts due to no mechanical failure. Reference number 7004475830"

We serviced a

SAMSUNG WASHER-FRONT LOA

Model WF42H5400AW/A2

Near Enumclaw, WA 98022

Branden W.

Job Details: 08/05/2021

Customer concern is that washer does not clean well and can smell bleach. Cycle tested. Foumd drain hose about 2 feet too far in wall drain causing hose to go past p trap. Secured hose 6 inches into drain. No mechanical issues found. Also advised to only use 2 tablespoons of detergent and run clean cycle regularly. All checks ok.

We serviced a

KENMORE DRYER-ELECTRIC

Model 11060096990

Near Frisco, TX 75035

Jacob P.

Job Details: 08/05/2021

"Installed previously ordered control panel. Test cycled, all checks ok."

We serviced a

MAYTAG WASHER-FRONT LOA

Model MHW7000XW0

Near Puyallup, WA 98374

Branden W.

Job Details: 08/05/2021

Installed new MCU. Also found inner portion of door boot where it meets drum not installed properly. Corrected door boot. Cycle tested through diagnostic and rinse and spin. All checks ok.

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWB835DW0

Near Garland, TX 75043

Jacob P.

Job Details: 08/05/2021

"Installed previously ordered console. Test cycled, all checks ok."

We serviced a

KENMORE DRYER-ELECTRIC

Model 1162622101

Near Dallas, TX 75231

Jacob P.

Job Details: 08/05/2021

"Customer concern of dryer not heating. Customer advised that issue is intermittent and has worked since initial call made for service. Test cycled unit through each cycle, unit heats. Checked contacts in timer through each cycle, checks ok. Ran air flow test, yellow. Test cycled temps ?5 through each cycle, temps in range. Advised customer that vent from back of dryer needs to be cleaned. Unit is functioning as designed at time of service."

We serviced a

GE LAUNDRY CENTER

Model GUD24ESSM1WW

Near Tacoma, WA 98418

Branden W.

Job Details: 08/05/2021

Installed new inlet valve. Cycle tested. All checks good. Left failed part with customer as it caused a water leak.

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV400EWHDWR/AA

Near Puyallup, WA 98373

Cameron M.

Job Details: 08/04/2021

"Customer concern is that dryer does not tumble. Found heating element shorted to element case .also found open thermal fuse,causing unit to power but not tumble and heat. Cleaned and Vacuumed inside of dryer. Installed new element and thermal fuse. Cycle tested, all checks good. ; used 1 DC47-00016A (THERMAL FUSE), and 1 DC97-14486A (ELEMENT ASSEMBLY) from stock"

We serviced a

SAMSUNG WASHER-FRONT LOA

Model WF42H5200AP/A2 11

Near Tacoma, WA 98407

Branden W.

Job Details: 08/04/2021

Installed new door boot. Cycle tested. All checks good. Took failed part that caused a leak at customer request.

We serviced a

WHIRLPOOL WASHER-TOPLOAD

Model WTW5000DW2

Near Richardson, TX 75080

Jacob P.

Job Details: 08/04/2021

"Installed previously ordered suspension rods. Test cycled, all checks ok."

We serviced a

GE LAUNDRY CENTER

Model GUD27GSSM2WW

Near Puyallup, WA 98372

Cameron M.

Job Details: 08/04/2021

"Customer concern is that sheet stuck under agitator. Found sheet stuck under agitator, causing unit to not agitate. Removed agitator then unwrapped sheet from main shaft, re-installed agitator. Cycle tested unit all checks good."

We serviced a

WHIRLPOOL DISHWASHER

Model WDT970SAHZ0

Near Frisco, TX 75035

Jacob P.

Job Details: 08/04/2021

"Installed previously ordered inlet valve. Test cycled, all checks ok."

We serviced a

KENMORE DRYER-ELECTRIC

Model 41781100002

Near Rowlett, TX 75088

Jacob P.

Job Details: 08/04/2021

"Installed previously ordered belt. Test cycled, all checks ok."

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAHZ0

Near Graham, WA 98338

Branden W.

Job Details: 08/04/2021

"Customer concern is that dishwasher does not dry and upper rack is falling. Found dishwasher in heat lock out (F7 E1) reset through diagnostic cycle. Cycle tested. Good water level, spray pressure and heat. Unable to find any issue. Replaced broken upper rack adjuster kit. All checks good. ; used 1 W10712395 (ADJUSTER) from stock"

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DVE52M8650V/A3

Near Puyallup, WA 98375

Branden W.

Job Details: 08/04/2021

Installed new user board. Found dryer duct came off at blower housing. Likely cause of moisture buildup. Secured duct with metal heat tape to blower housing. Cycle tested. All checks good.

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model WED9600TA0

Near Spanaway, WA 98387

Branden W.

Job Details: 08/04/2021

Installed new main control. Cycle tested. All checks good.

We serviced a

MAYTAG DRYER-ELECTRIC

Model MEDC465HWO

Near Spanaway, WA 98387

Cameron M.

Job Details: 08/04/2021

Customer concern is that dryer takes multiple cycles to dry clothes. Preformed airflow test failed (red). Cleaned and calibrated moisture sensors. Advised customer dryer vent needs to be shortened. Also advised customer dryer duct needs to be cleaned asap

We serviced a

MAGIC CHEF RANGE

Model CES3540AAC

Near Puyallup, WA 98375

Branden W.

Job Details: 08/03/2021

"Customer concern is that range does not heat. Found all elements, cooktop and oven do not produce heat. Found only 120vac supplied to range causing no heat. Found loose wall plug causing poor connection with power cord. Was able to get 240vac to range. Tested all elements. All check good. Advised that an electrician is needed to replace wall plug. Range is sitting on board runners and not feet of range. Did not remove range. Accessed power plug from under range."

We serviced a

KENMORE DRYER-GAS

Model 11065132411

Near Coppell, TX 75019

Jacob P.

Job Details: 08/03/2021

"Customer concern of long dry times and not much lint in trap. Ran air flow test, 100% plugged. Removed vent and ran air flow test again, passed. Advised customer that vent from back of dryer to outside needs to be cleaned asap. Unit functioning as designed."

We serviced a

GE DISHWASHER

Model GDF450PSR0SS

Near Lewisville, TX 75067

Jacob P.

Job Details: 08/03/2021

"Customer concern of door not latching. Found unit installed improperly causing door not to latch. Reinstalled unit. Test cycled, all checks ok."

We serviced a

LG DRYER-ELECTRIC

Model DLEX3570V

Near Puyallup, WA 98375

Branden W.

Job Details: 08/03/2021

Installed new main control. Cycle tested. All checks good.

We serviced a

KITCHENAID DISHWASHER

Model KDTM354DSS4

Near Bonney Lake, WA 98391

Branden W.

Job Details: 08/03/2021

"Installed new sump assembly, spray arms and turbidity sensor. Cycle tested x3. All checks good."

We serviced a

GE DISHWASHER

Model GDF570SSJ0SS

Near Buckley, WA 98321

Branden W.

Job Details: 08/03/2021

Installed new control board. Cycle tested. All checks good.

We serviced a

KENMORE COOKTOP

Model 79032683411

Near Dallas, TX 75211

Jacob P.

Job Details: 08/03/2021

"Installed previously ordered valves, burner bodies and orifice holders. Test cycled, all checks ok."

We serviced a

SAMSUNG RANGE

Model NE58K9430SS/AA

Near Tacoma, WA 98446

Branden W.

Job Details: 08/03/2021

Installed new infinite switches. Cycle tested. All checks ok.

We serviced a

KENMORE WASHER-FRONT LOA

Model 79640512900

Near Tacoma, WA 98498

Cameron M.

Job Details: 08/03/2021

"Customer concern is that washer does not drain strted producing oe error intermittently a week ago, now leaves water in unit. Found failed drain pump, causing unit to not drain. Needs new drain pump. Installed new drain pump, cycle tested unit 3x. All checks good ; used 1 4681EA2001T (DRAIN PUMP) from stock"

We serviced a

HOTPOINT DRYER-ELECTRIC

Model HTDX100EM8WW

Near Lakewood, WA 98498

Cameron M.

Job Details: 08/03/2021

"Customer concern is that dryer does not heat, takes hours to dry clothes. Preformed airflow test, failed (red).found shorted contact on lower right connector of element, causing unit to not heat during operation. Needs new terminal connector. Installed new thermal spade, cycle tested unit all check good.Advised customer dryer duct needs to be cleaned asap before dryer use resumes. ; used 1 279457 (WIRE-SPADE) from stock"

We serviced a

KENMORE DRYER-ELECTRIC

Model 110.696228

Near Spanaway, WA 98387

Cameron M.

Job Details: 08/02/2021

"Customer concern is that dryer does not heat. Preformed airflow test failed (yellow).found open heating element, causing unit to not heat. Needs new heating element. Installed new heating element. Cycle tested all checks good. ; used 1 279838 (ELEMENT,HEATER) from stock"

We serviced a

SAMSUNG WASHER-FRONT LOA

Model WF448AAP/XAA

Near Spanaway, WA 98387

Cameron M.

Job Details: 08/02/2021

"Customer requested maintenance and service . Cleaned out drain pump .cycle tested unit. Found a slight leak from door boot , Advised customer on keeping sealing surface clean to prevent future leaks."

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWB725BW0

Near Tacoma, WA 98406

Branden W.

Job Details: 08/02/2021

"Installed new bearing kit, rotor, stator and hub. Cycle tested. All checks good."

We serviced a

SAMSUNG WASHER-FRONT LOA

Model WV55M9600AV/A5 02

Near Lakewood, WA 98498

Cameron M.

Job Details: 08/02/2021

"Installed previously ordered display assembly. Cycle tested, all checks good."

We serviced a

JENN-AIR COOKTOP

Model C221

Near Fairview, TX 75069

Jacob P.

Job Details: 08/02/2021

"Installed previously ordered infinite switch. Test cycled, all checks ok."

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWB835DW4

Near Sumner, WA 98391

Branden W.

Job Details: 08/02/2021

Installed new washplate. Removed a lot of coins from under plate. Advised to check pockets to prevent coins in washer. All checks ok.

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model WED4815EW1

Near Dallas, TX 75220

Jacob P.

Job Details: 08/02/2021

"Installed previously ordered timer. Test cycled, all checks ok."

We serviced a

GE DRYER-ELECTRIC

Model GTX22EASK0WW

Near Irving, TX 75063

Jacob P.

Job Details: 08/02/2021

"Customer concern of unit making loud noise. Test cycled, unit functioning fine. Ran air flow test, failed. Advised customer that dryer duct to outside needs to be cleaned. Unit functioning as designed."

We serviced a

GE DISHWASHER

Model GDF535PSR0SS

Near Irving, TX 75063

Jacob P.

Job Details: 08/02/2021

"Customer concern of unit not draining. Found garbage disposal plug still in causing no drain. Removed plug. Test cycled, all checks ok."