Service History 137 - RPS Appliance Repair

We serviced a

KITCHENAID DISHWASHER

Model KDPE234GPS0

Near Puyallup, WA 98374

Cameron M.

Job Details: 04/29/2021

"Customer concern is that dishwasher will start a cycle but doesn't fill. Checked voltage from main board to fill valve. Found loose connection at fill valve causing no fill condition. Reseated water inlet valve power connector, cycle tested unit 10x. unit operating as designed. Advised customer to call if issue returns."

We serviced a

WHIRLPOOL DISHWASHER

Model WDF510PAYS8

Near McKinney, TX 75070

Bud L.

Job Details: 04/29/2021

Installed previously ordered heating element. Test cycled and all checks ok.

We serviced a

FRIGIDAIRE DISHWASHER

Model FBD2400KW12B

Near Garland, TX 75040

Bud L.

Job Details: 04/29/2021

Installed previously ordered spray arm. Test cycled and all checks ok.

We serviced a

WHIRLPOOL OVEN/STOVE

Model GMC305PRS01

Near Lewisville, TX 75056

Bud L.

Job Details: 04/28/2021

"Came to install repaired control board and touch pad, found control board supports broken and ribbon cable connector for touch pad broken. Called ahs, unit is being put into replacement options. Auth code 216pjol."

We serviced a

WHIRLPOOL WASHER-TOPLOAD

Model WTW4800XQ2

Near Tacoma, WA 98445

Cameron M.

Job Details: 04/28/2021

Installed new suspension rods. Cycle tested. All checks good.

We serviced a

GE DRYER-ELECTRIC

Model GTX18ESSJ0WW

Near Puyallup, WA 98372

Cameron M.

Job Details: 04/28/2021

Installed new belt. Cycle tested. All checks good.

We serviced a

WHIRLPOOL RANGE

Model WFE540H0AS0

Near Bonney Lake, WA 98391

Cameron M.

Job Details: 04/28/2021

Installed new control and temp probe. Tested at 350. All checks good.

We serviced a

WHIRLPOOL WASHER-TOPLOAD

Model WTW8500BW0

Near Sachse, TX 75048

Bud L.

Job Details: 04/28/2021

Installed previously ordered dispenser. Test cycled and all checks ok. Left failed part with.

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model WED5550SQ0

Near Rowlett, TX 75088

Bud L.

Job Details: 04/28/2021

"Customer concern unit not turning on. Found that the thermal fuse was open causing unit not to start. Replaced thermal fuse. Tested in air fluff, no heat. Ran air flow test, yellow. Test cycled temps, 120-230. Removed vent and test cycled temps again, 120-220. Found thermistor ohms out of range causing dryer to get too hot. Replaced thermistor. Test cycled temps without vent, 120-190. Advised customer that vent from back of dryer to outside needs to be cleaned. Unit functioning as designed.; used 1 WP3392519 ( FUSE-THRML), and 1 WP3387134 ( THRMST-FIX) from stock"

We serviced a

KENMORE DRYER-GAS

Model 11061402310

Near Dallas, TX 75233

Bud L.

Job Details: 04/28/2021

Installed previously ordered felt seal. Advised customer to let glue dry for 24 hours before use.

We serviced a

ELECTROLUX DISHWASHER

Model EI24ID30QS3B

Near Frisco, TX 75035

Bud L.

Job Details: 04/27/2021

"Customer concern of pump running and console not responsive. Found bottom of dishwasher full of water triggering leak sensor. Cleaned out water. Test cycled, no leaks. All checks ok."

We serviced a

SAMSUNG WASHER-FRONT LOA

Model WF42H5200AP/A2

Near Allen, TX 75002

Bud L.

Job Details: 04/27/2021

"Installed previously ordered inverter board. Unable to remove stator to install hall sensor. Test cycled with a load, all checks ok."

We serviced a

GE DISHWASHER

Model DDT595SSJ2SS

Near Rowlett, TX 75089

Bud L.

Job Details: 04/27/2021

Installed previously ordered control board. Test cycled and all checks ok.

We serviced a

FRIGIDAIRE DRYER-ELECTRIC

Model GLEQ332AS2

Near South Hill, WA 98374

Cameron M.

Job Details: 04/27/2021

Customer concern is that timer knob broke. Found timer knob broke causing difficulty to select cycle and run dryer. Needs new timer knob. Customer will install new knob.

We serviced a

GE DRYER-ELECTRIC

Model DBVH520EJ2WW

Near Puyallup, WA 98374

Cameron M.

Job Details: 04/27/2021

Installed new front and rear bearings. Cycle tested. All checks good.

We serviced a

WHIRLPOOL WASHER-FRONT LOA

Model WFW96HEAW0

Near Gig Harbor, WA 98335

Cameron M.

Job Details: 04/27/2021

Installed customer provided door boot. Cycle tested. All checks good. No warranty as part was provided by customer.

We serviced a

KITCHENAID DISHWASHER

Model KDTE254ESS2

Near Tacoma, WA 98418

Cameron M.

Job Details: 04/27/2021

"Customer concern is that dishwasher is not getting dishes clean and started making noise mid cycle. Checked drain pump for debris, found nothing. Cycle tested unit in service mode found no mechanical issues at this time. Advised customer to monitor unit, and call if issue persists."

We serviced a

LG WASHER-FRONT LOA

Model WM3570HVA

Near Garland, TX 75043

Bud L.

Job Details: 04/27/2021

Installed previously ordered control board. Test cycled and all checks ok.

We serviced a

SAMSUNG WASHER-FRONT LOA

Model WF45N5300AW

Near Dallas, TX 75209

Bud L.

Job Details: 04/26/2021

Customer concern after previous technician visits unit has been shaking and noisy. Found screws for bottom of front panel not installed and unit unleveled. Installed replacement screws are leveled machine. Test cycled and all checks ok.

We serviced a

GE DRYER-ELECTRIC

Model GFD14ESS0WW

Near Dallas, TX 75209

Bud L.

Job Details: 04/26/2021

"Customer concern of intermittent squeaking sound. Test cycled dryer, unable to verify noise. Inspected front felt seal, belt and pulley, all checks ok. Advised customer to call back if problem persists."

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV48J7770EP/A2 01

Near Graham, WA 98338

Cameron M.

Job Details: 04/26/2021

"Customer concern is that dryer makes noise during operation. Found failed front right roller, causing noise during operation. Replaced front right roller cleaned and lubed all other rollers. Cycle tested all checks good ; used 1 DC97-16782A ( DRUM ROLLER) from stock"

We serviced a

WHIRLPOOL RANGE

Model WFE515S0ES0

Near Tacoma, WA 98408

Cameron M.

Job Details: 04/26/2021

Installed new switches. Cycle tested all burners. All working properly at this time.

We serviced a

SAMSUNG WASHER-FRONT LOA

Model WF431ABPXAA01

Near Allen, TX 75002

Bud L.

Job Details: 04/26/2021

Customer concern of LE error. Found that drain hose was too far in wall. Made adjustments to drain hose. Test cycled and all checks ok.

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DVE45R6100C/A3

Near Puyallup, WA 98373

Cameron M.

Job Details: 04/26/2021

Customer concern is that dryer makes grinding noise during operation. Found drawstring wound around motor shaft behind blower wheel. Removed drawstring. Cycle tested. All checks good.

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWB835DC4

Near Eatonville, WA 98328

Cameron M.

Job Details: 04/26/2021

Installed new lid lock. Cycle tested. All checks good.

We serviced a

GE DISHWASHER

Model GDT530PSD4SS

Near Garland, TX 75040

Bud L.

Job Details: 04/26/2021

Installed previously ordered UI board and door harness. Test cycled and all checks ok.

We serviced a

SAMSUNG WASHER-TOPLOAD

Model WA50R5400AV/US 02

Near Sachse, TX 75048

Bud L.

Job Details: 04/23/2021

"Installed previously ordered control board and lid lock. Test cycled ×10, all checks ok."

We serviced a

MAYTAG DISHWASHER

Model DWU9302AAB

Near Dallas, TX 75228

Bud L.

Job Details: 04/23/2021

"Installed previously ordered inlet valve. Installed new fill hose. Test cycled, all checks ok. ; used 1 41045 ( FILL HOSE DW 6' W/FITTINGS) from stock"

We serviced a

WHIRLPOOL DISHWASHER

Model WDT730PAHZ

Near Graham, WA 98338

Cameron M.

Job Details: 04/23/2021

Installed new wash pump and grommet. Cycle tested. All checks good.

We serviced a

GE DISHWASHER

Model GDT645SYN3FS

Near Dallas, TX 75205

Bud L.

Job Details: 04/23/2021

Customer concern that unit not draining. Test cycled upon arrival unit drains. Test cycled X3 and all checks ok.

We serviced a

KENMORE LAUNDRY CENTER

Model 41761722510

Near Dallas, TX 75235

Bud L.

Job Details: 04/23/2021

"Installed previously ordered belt. Test cycled, all checks ok."

We serviced a

GE WASHER-FRONT LOA

Model GTW750CSL1WS

Near McKinney, TX 75070

Bud L.

Job Details: 04/23/2021

"Installed previously ordered detergent dispenser. Test cycle, all checks ok."

We serviced a

GE WASHER-FRONT LOA

Model WHDVH626FWW

Near Puyallup, WA 98374

Cameron M.

Job Details: 04/23/2021

Installed new inlet valve. Cycle tested. All checks good.

We serviced a

KITCHENAID DISHWASHER

Model KDTE334GPS0

Near Gig Harbor, WA 98335

Cameron M.

Job Details: 04/23/2021

Customer concern is that dishwasher does not clean well. Found spray arms clogged causing very poor spray pressure and rotation. Needs new spray arms. Found no other mechanical issues. Advised to thoroughly clean dishwasher with afresh or vinegar cycles. Customer will order and install new spray arms.

We serviced a

KENMORE WASHER-FRONT LOA

Model 11026132411

Near Allen, TX 75002

Bud L.

Job Details: 04/23/2021

Performed pm check. Test cycled and all checks ok.

We serviced a

HOTPOINT WASHER-TOPLOAD

Model HTW240ASK5WS

Near Allen, TX 75002

Bud L.

Job Details: 04/22/2021

"Installed previously ordered lid strike. Test cycled, all checks ok."

We serviced a

MAYTAG WASHER-TOPLOAD

Model PAVT234AWW

Near Richardson, TX 75080

Bud L.

Job Details: 04/22/2021

"Customer concern of unit leaking. Found inlet dispenser housing separated causing leak. Connected housing properly. Test cycled, all checks ok."

We serviced a

SAMSUNG WASHER-TOPLOAD

Model WA52J8700AP/A2 02

Near Lakewood, WA 98498

Cameron M.

Job Details: 04/22/2021

"Customer concern is that washer goes out of balance occasionally. Cycle tested washer. Found no mechanical issues, Advised out of balance happen occasionally."

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV36J4000EW/A3

Near Tacoma, WA 98444

Cameron M.

Job Details: 04/22/2021

"Customer concern is that dryer run does not heat.ran airflow test failed (red).Found broken rear right roller. Also found open heating element causing unit to run but not heat. Installed new element and roller, vacuumed inside of dryer, cycle tested all checks good.Advised customer dryer duct needs to be cleaned asap.; used 1 DC97-14486A ( ELEMENT ASSEMBLY), and 1 DC97-16782A ( DRUM ROLLER) from stock"

We serviced a

KENMORE RANGE

Model 79093019312

Near Grand Prairie, TX 75050

Bud L.

Job Details: 04/22/2021

"Installed previously ordered control board and overlay. Test cycled, all checks ok."

We serviced a

ELECTROLUX WASHER-FRONT LOA

Model EFLS527UTT

Near Dallas, TX 75211

Bud L.

Job Details: 04/22/2021

"Installed previously ordered door boot. Test cycled, all checks ok."

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV48H7400EW/A2 01

Near Bonney Lake, WA 98391

Cameron M.

Job Details: 04/21/2021

"Customer concern is that dryer run but does not heat. Ran airflow test failed (yellow).found open heating element causing dryer to not heat. Cleaned and lubed right rear roller,vacuumed inside of dryer, installed new heating element, cycle all checks good. Advised customer dryer vent needs to be cleaned asap.; used 1 DC97-14486A ( ELEMENT ASSEMBLY) from stock"

We serviced a

WHIRLPOOL LAUNDRY CENTER

Model LTE5243DQ3

Near Tacoma, WA 98498

Cameron M.

Job Details: 04/21/2021

Customer concern is that washer does not drain. Found failed lid switch causing washer to not drain or spin. Replaced lid switch. Cycle tested. Washer operating as designed. No hot water supplied to washer. Advised that a plumber is needed. ; used 1 WP3355806 ( SWITCH-LID) from stock

We serviced a

WHITE WESTING DRYER-ELECTRIC

Model n/a

Near University Place, WA 98466

Cameron M.

Job Details: 04/21/2021

Model and serial tag worn offCustomer concern is that dryer makes loud squeaking noise. Found rear drum bearing dry. Cleaned and lubed bearing. Cycle tested. All checks good.

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV45H7000EW/A2 02

Near Dallas, TX 75223

Bud L.

Job Details: 04/21/2021

"Customer concern of unit making noise. Found idler pulley and rear rollers seized causing noise. Replaced pulley and rear rollers. Test cycled, all checks ok. ; used 1 DC93-00634A ( IDLER ASSEMBLY), and 2 DC97-16782A ( DRUM ROLLER) from stock"

We serviced a

WHIRLPOOL DISHWASHER

Model WDF760SADB2

Near Puyallup, WA 98374

Cameron M.

Job Details: 04/21/2021

"Customer concern is that dishwasher leaks, customer advised unit hasn't leak after four loads prior to service,and makes grinding noise. Cycle tested and visually inspected under unit, found no active leaks, did find signs of past oversuds. Found no mechanical issues present. Advised customer to call if issue returns."

We serviced a

MAYTAG DRYER-GAS

Model LDG7500AAW

Near McKinney, TX 75071

Bud L.

Job Details: 04/21/2021

Installed previously ordered door switch and thermostat. Test cycled and all checks ok.

We serviced a

MAYTAG DISHWASHER

Model MDB4949SDM0

Near Federal Way, WA 98023

Cameron M.

Job Details: 04/21/2021

Installed new sump assembly. Cycle tested x3. All checks good. Water supply shut off undersink does not stop water flow and should be addressed by a plumber.

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DVE45R6100W/A3

Near Puyallup, WA 98373

Cameron M.

Job Details: 04/21/2021

"Customer concern is that dryer runs but doesn't heat. preformed airflow test, failed. Found open heating element causing no heat. Replaced element. Vacuumed inside dryer. Cycle tested. Good heat advised to have dryer duct cleaned asap. ; used 1 DC97-14486A ( ELEMENT ASSEMBLY) from stock"

We serviced a

GE RANGE

Model JB710ST3SS

Near Tacoma, WA 98404

Cameron M.

Job Details: 04/20/2021

"Customer concern is that range shuts off intermittently. Checked power and wiring throughout range. No issues found. Advised is problem persists, have an electrician check wall plug and breaker box. Left unit slid out at customers request."

We serviced a

KENMORE WASHER-TOPLOAD

Model 11025132410

Near Tacoma, WA 98408

Cameron M.

Job Details: 04/20/2021

"Customer concern is that washer will not advance cycle. Cycle tested in service mode and normal Cycle, no issues found. Unit was unplugged at time of arrival, Advised customer we will be in area and to run a load and call if issue persists.NO CHARGE."

We serviced a

LG RANGE

Model LRE3194ST/00

Near Tacoma, WA 98409

Cameron M.

Job Details: 04/20/2021

Installed new console assembly. Cycle tested. All checks good. Advised that wall plug is loose and should be addressed soon.

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model WED5620HW0

Near Sumner, WA 98390

Cameron M.

Job Details: 04/20/2021

"Customer concern is that dryer makes squeaking noise intermittently. Found small pebbles in drum glides and in lint screen, causing scraping sound. Cleaned out pebbles and cycle tested with load . No mechanical issues."

We serviced a

LG WASHER-FRONT LOA

Model WM3270CW

Near Tacoma, WA 98409

Cameron M.

Job Details: 04/20/2021

Customer concern is that washer does not drain. Found failed drain pump causing unit to not drain. Replaced drain pump. Cycle tested. All checks good. ; used 1 4681EA2001T (DRAIN PUMP) from stock

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV48J7770EP/A2

Near Tacoma, WA 98407

Cameron M.

Job Details: 04/20/2021

"Customer concern is that dryer makes noise. Found worn rear roller causing noise. Also found glazed drum belt. Replaced both rear rollers and belt. Vacuumed inside of dryer. Cycle tested. All checks good. ; used 1 6602-001655 (BELT), and 2 DC97-16782A (DRUM ROLLER) from stock"

We serviced a

GE DISHWASHER

Model GDT645SYN0FS

Near Graham, WA 98338

Cameron M.

Job Details: 04/20/2021

Customer concern is that dishwasher starts a cycle then five minutes in shuts off. Found dishwasher not draining causing it to stop in cycle. Cleaned debris from airgap causing no drain. Cycle tested. All checks good.

We serviced a

WHIRLPOOL RANGE

Model WFG525S0HZ1

Near Puyallup, WA 98374

Cameron M.

Job Details: 04/20/2021

Customer concern is that oven does not heat on bake and produces gas smell. Found DSI ignitor arcing to drawer causing no ignition. Shielded bare section of ignitor wire. Cycle tested x10. All checks good. Advised to call if issue returns.

We serviced a

WHIRLPOOL WASHER-FRONT LOA

Model WFW75HEFW0

Near Tacoma, WA 98445

Cameron M.

Job Details: 04/16/2021

"Customer concern is that washer is leaking water from the bottom of unit. Found hair on door boot causing water to leak, also found Signs of over suds. Advised customer of running the clean washer cycle regularly."

We serviced a

GE DISHWASHER

Model PDT785SYN2FS

Near Buckley, WA 98321

Cameron M.

Job Details: 04/16/2021

Customer concern is that dishwasher leaks small amount of water from vent when drying. Updated to latest software per TSB. Advised to call if issue persists.

We serviced a

KENMORE DRYER-ELECTRIC

Model 11061202011

Near Graham, WA 98338

Cameron M.

Job Details: 04/16/2021

Installed timer sent by sears. Cycle tested. All checks good.

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWC555DW0

Near Spanaway, WA 98387

Branden W.

Job Details: 04/15/2021

Installed new washplate and hub. Calibrated washer. Cycle tested. All checks good.

We serviced a

WHIRLPOOL DISHWASHER

Model WDT730PAHZ0

Near Tacoma, WA 98408

Branden W.

Job Details: 04/15/2021

Installed new wash pump and grommet. Cycle tested. All checks good.

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWX655DW1

Near Enumclaw, WA 98022

Branden W.

Job Details: 04/15/2021

Installed new main control. Calibrated washer. Cycle tested. All checks good.

We serviced a

WHIRLPOOL DISHWASHER

Model WDT730PAHZ0

Near Orting, WA 98360

Branden W.

Job Details: 04/15/2021

Installed new sump/motor assembly. Cycle tested. All checks good.

We serviced a

MAYTAG DISHWASHER

Model MDB7749SBB3

Near Tacoma, WA 98445

Branden W.

Job Details: 04/15/2021

Installed new console and handle. Cycle tested. All checks good.

We serviced a

KITCHENAID OVEN/STOVE

Model KERS807SSS00

Near Tacoma, WA 98402

Cameron M.

Job Details: 04/15/2021

Customer concern is that range bakes unevenly and does not beep when preheated. Found aluminum foil lining bottom cover of oven causing uneven heat. Found preheat sound set to off in settings. Turned on. Cycle tested to 350. All checks good at this time.

We serviced a

MAYTAG DRYER-ELECTRIC

Model MEDX655DW1

Near Tacoma, WA 98467

Cameron M.

Job Details: 04/15/2021

"Customer concern is that dryer takes multiple cycles to dry clothes. Preformed airflow test failed (yellow) ,cleaned moisture sensors, Preformed temperature checks. Found no mechanical issues at this time, Advised customer dryer vent needs to be cleaned and shortened. Advised customer to call if issue persists"

We serviced a

MAYTAG DISHWASHER

Model MDB4949SDM0

Near Eatonville, WA 98328

Cameron M.

Job Details: 04/13/2021

"Customer concern is dishwasher does not power on. Checked power supply connection, checked supply voltage to control. good voltage. found loose connection from main board to user interface causing dishwasher to not power on. Reconnected user interface to main board, cycle tested all checks good"

We serviced a

FRIGIDAIRE WASHER-FRONT LOA

Model FFFS5115PW0

Near Tacoma, WA 98408

Cameron M.

Job Details: 04/13/2021

"Installed new door hinge, frame and panel. Cycle tested. All checks good."

We serviced a

GE WASHER-FRONT LOA

Model GTW680BSJ4WS

Near Mesquite, TX 75150

Jacob P.

Job Details: 04/13/2021

Installed previously ordered drain pump. Test cycled and all checks ok.

We serviced a

GE WASHER-TOPLOAD

Model GTW465ASN1WW

Near Dallas, TX 75227

Jacob P.

Job Details: 04/13/2021

Customer concern that unit making loud sound. Found belt sitting too low on motor and pulley. Readjusted belt. Test cycled with load and all checks ok.

We serviced a

GE DRYER-ELECTRIC

Model GTD65EBPL1DG

Near Dallas, TX 75217

Jacob P.

Job Details: 04/13/2021

"Customer concern unit shutting off after 2 minutes. Checked that moisture sensors were connected. Test cycled and timed dry, checks ok, test cycled in normal dry with simulated load, all checks ok. Unit functioning as designed. Advised customer to use timed dry when running mixed loads."

We serviced a

MAYTAG WASHER-FRONT LOA

Model MHWE300VF00

Near Dallas, TX 75228

Jacob P.

Job Details: 04/13/2021

Customer concern that unit not draining. Found debri in drain pump impeller. Removed debri. Test cycled and all checks ok.

We serviced a

GE DRYER-ELECTRIC

Model GTX42EASJ2WW

Near McKinney, TX 75071

Jacob P.

Job Details: 04/13/2021

"Customer concern of condensation build up in laundry room when using dryer. Found vent behind dryer crushed and bent causing dryer to vent into laundry room. Replaced vent and secured to dryer. Ran air flow test, failed. Advised customer that vent from back of dryer to outside needs to be cleaned. Unit functioning as designed. ; used 1 BTD48 (4: X 8' FLEX DUCT), and 2 MC450 (4' WORM CLAMP) from stock"

We serviced a

GE RANGE

Model CGS750P4M2W2

Near Dallas, TX 75214

Jacob P.

Job Details: 04/13/2021

Installed previously ordered door switch and light assemblies. Test cycled and all checks ok.

We serviced a

WHIRLPOOL WASHER-TOPLOAD

Model WTW8500BW0

Near Sachse, TX 75048

Jacob P.

Job Details: 04/13/2021

Customer concern of unit leaking. Found detergent dispenser hose cracked. Needs new detergent dispenser.

We serviced a

GE WASHER-TOPLOAD

Model GTW220ACK6WW

Near Frisco, TX 75034

Jacob P.

Job Details: 04/13/2021

"Customer concern that unit not drying. Found debri in drain pump causing no drain. Removed debri, test cycled and all checks ok."

We serviced a

GE COOKTOP

Model PP9830DJ1BB

Near Dallas, TX 75287

Jacob P.

Job Details: 04/13/2021

Installed previously ordered fan switch. Test cycled and all checks ok.

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWC565FW1

Near Spanaway, WA 98387

Cameron M.

Job Details: 04/13/2021

Customer concern is that washer does not turn on. Found 120v to main board. Board has no output. Needs new main board. Declined to repair at this time.

We serviced a

GE DRYER-ELECTRIC

Model DBSR453EB3WW

Near Spanaway, WA 98387

Cameron M.

Job Details: 04/13/2021

Installed new belt. Vacuumed inside of dryer. Cycle tested. Dryer operating as designed.

We serviced a

GE WASHER-FRONT LOA

Model GFW450SSM1WW

Near Bonney Lake, WA 98391

Cameron M.

Job Details: 04/13/2021

Customer concern is that washer leaks and intermittently does not spin properly. Found large piece of Styrofoam under tub causing out of balance conditions. Only signs of leak is from door boot and glass seal. Advised to keep boot and glass clean to prevent leak. Washer operating as designed at this time.

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model LER5636PQ0

Near Puyallup, WA 98375

Cameron M.

Job Details: 04/13/2021

Customer concern is that dryer takes multiple cycles to dry. Found lint screen clogged. Also found vent crushed behind dryer. Shortened duct to prevent crushing. Ran airflow test. Test passed. Advised customer that lint screen must be cleaned after every cycle.

We serviced a

WHIRLPOOL OVEN/STOVE

Model WFG110AVQ0

Near Puyallup, WA 98373

Cameron M.

Job Details: 04/13/2021

Customer concern is that oven does not ignite and top burners do not turn down. Customer replaced ignitor. Found ignitor drawing 3.4 amps. Ignitor good. Found valve off at regulator causing no gas flow to bake. Switched valve. Cycle tested. Found flame too high. Unit set up for natural gas not LP. Advised a gas company is needed to convert unit. NO CHARGE

We serviced a

GE WASHER-TOPLOAD

Model HTW200ASK0WW

Near McKinney, TX 75069

Jacob P.

Job Details: 04/13/2021

Customer concern unit leaking. Found stand pipe overflowing when draining. Advised customer that plumber is needed.

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model WED8500DC4

Near Tacoma, WA 98445

Cameron M.

Job Details: 04/13/2021

"Customer concern is that dryer makes noise during operation. Found clothing caught in blower wheel , causing noise. Removed clothing. Advised customer not to run dryer without lint trap."

We serviced a

KITCHENAID DISHWASHER

Model KDFE104DWH1

Near Plano, TX 75025

Jacob P.

Job Details: 04/13/2021

Customer concern that unit will not drain. Found debri in drain pump impeller. Replaced drain pump. Test cycled and all checks ok. ; used 1 WPW10348269 (PUMP-DRAIN) from stock

We serviced a

GE DISHWASHER

Model PDT845SMJ2ES

Near DuPont, WA 98327

Cameron M.

Job Details: 04/13/2021

"Customer concern is that dishwasher is leaking water into leak try triping leak error after disposal back up. Cycle tested using newfi and normal Cycle mode, found leaks present. Unit operating as designed. Customer removed toe panel prior to service."

We serviced a

WHIRLPOOL WASHER-FRONT LOA

Model WFW6620HC0

Near Orting, WA 98360

Cameron M.

Job Details: 04/13/2021

"Installed previously ordered door boot, cycle tested all checks good. No leaks left failed part as it caused a water."

We serviced a

MAYTAG DRYER-ELECTRIC

Model MEDC200XW1

Near Puyallup, WA 98374

Cameron M.

Job Details: 04/08/2021

"Installed previously ordered timer, cycle tested all checks good."

We serviced a

WHIRLPOOL WASHER-TOPLOAD

Model WTW7300DW0

Near Puyallup, WA 98374

Cameron M.

Job Details: 04/08/2021

Customer concern is that washer is leaking from fill hoses. Checked connections from wall water valve to washer inlet found no active leaks present. Found it to be detergent dripping from top shelf. Unit operating as designed. Advised customer to call if issue returns.

We serviced a

AMANA DRYER-ELECTRIC

Model LEA90AW

Near Rockwall, TX 75032

Jacob P.

Job Details: 04/08/2021

"Customer concern that unit not heating, found that plug not seated. Reseated plug, cycled test and all checks ok."

We serviced a

WHIRLPOOL WASHER-FRONT LOA

Model WTW8540BW1

Near Plano, TX 75025

Jacob P.

Job Details: 04/08/2021

Customer concern unit not spinning. Found debri between basket and tub causing friction. Removed debri test cycled all checks ok.

We serviced a

GE WALL OVEN

Model JTS5000SN1SS

Near Murphy, TX 75094

Jacob P.

Job Details: 04/08/2021

Installed previously ordered door glass. Test cycled all checks ok.

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model WSM2700DAWWW

Near Tacoma, WA 98405

Cameron M.

Job Details: 04/08/2021

Work order not needed. Laundry center.

We serviced a

SAMSUNG WASHER-TOPLOAD

Model WA476DSHAWR/A1

Near Tacoma, WA 98406

Cameron M.

Job Details: 04/08/2021

Customer concern is that washer does not drain and they want their drain pump installed. Installed customer provided drain pump (no warranty) Cycle tested. All checks good.

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV350AEW/XAA 03

Near Puyallup, WA 98375

Cameron M.

Job Details: 04/08/2021

Customer concern is that dryer runs but does not heat. Found open heating element causing no heat. Replaced element. Vacuumed inside of dryer. Cycle tested. All checks good. ; used 1 DC97-14486A ( ELEMENT ASSEMBLY) from stock

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model WED97HEDBD0

Near Mesquite, TX 75150

Jacob P.

Job Details: 04/08/2021

"Performed pm check, all checks ok"

We serviced a

LG DISHWASHER

Model LDP6797ST

Near Puyallup, WA 98375

Cameron M.

Job Details: 04/07/2021

Customer concern is that dishwasher still producing leak error. Found flood sensor tray full of water. Cleared water out. Cycle tested. Found very small leak from sump/motor connection causing error. Needs new sump and motor assembly. Customer will call if wanting to repair.

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model WED8000DW4

Near Bonney Lake, WA 98391

Cameron M.

Job Details: 04/07/2021

"Customer concern is that dryer makes noise during operation. Found failed idler pulley. Replaced idler pulley, cycle tested all checks good.; used 1 W10837240 (BRACKET) from stock"

We serviced a

SAMSUNG RANGE

Model NE597N0PBSR/AA

Near Bonney Lake, WA 98391

Cameron M.

Job Details: 04/07/2021

Customer concern is that range shows e85 error and heard an audible pop. Found no DC voltage out of main board to user interface board. Needs new main board. Declined to repair at this time.