We serviced a
GE COOKTOP
Model PGP989SN2SS
Near Allen, TX 75013
Jacob P.
Job Details:
03/23/2021
"Installed customer provided valves. Found gas line and electric undone upon arrival. Advised customer that hole in countertop is cut too large for cooktop and only glass is supporting unit. Had customer sign damage waiver due to improperly installed unit. Advised customer that repair is not under warranty due to customer provided parts. Test cycled, all checks ok."
We serviced a
KENMORE DRYER-ELECTRIC
Model 79681962710
Near DeSoto, TX 75115
Jacob P.
Job Details:
03/23/2021
"Performed pm check on dryer, air flow test failed. Advised customer that vent from back of dryer to outside needs to be cleaned. Unit functioning as designed."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV45K6500EV/A3 01
Near Tacoma, WA 98404
Cameron M.
Job Details:
03/23/2021
Installed new board. Cycle tested. All checks good.
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE50R5400V/A3
Near Seagoville, TX 75159
Jacob P.
Job Details:
03/23/2021
"Customer concern of unit not heating. Customer advised that previous tech told him that power supply cable ran to machine is not approved and needed to be fixed. Customer installed new cable and now has issues. Found power cord and outlet burnt. Checked all heating components, checks ok. Advised customer that new power cord and outlet need to be installed and possibly need an electrician to verify correct power is ran to machine. Unit functioning as designed."
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model GEW9250PW0
Near University Place, WA 98466
Cameron M.
Job Details:
03/23/2021
Installed new ui board. Cycle tested all checks good.
We serviced a
GE WASHER-TOPLOAD
Model GTW330ASK3WW
Near Dallas, TX 75211
Jacob P.
Job Details:
03/23/2021
"Installed previously ordered drain pump. Test cycled, all checks ok."
We serviced a
KENMORE DISHWASHER
Model 66513543N410
Near Tacoma, WA 98405
Cameron M.
Job Details:
03/23/2021
"Customer concern is that dishwasher does not heat. Found F7 E1 (heat lockout) and F6 E4 (oversuds) errors stored. Found rinse aid cap laying in bottom of dishwasher causing unit to not use rinse aid. Found excessive amount of suds causing errors and heat Loco out. Ran several rinse cycles to clear suds. Ran diagnostic cycle to clear heat lock out. Cycle tested heater, checks good. Advised to use good quality detergent and rinse aid. Found no other issues."
We serviced a
FRIGIDAIRE DRYER-ELECTRIC
Model FFQE5000QW1
Near Auburn, WA 98001
Cameron M.
Job Details:
03/23/2021
Customer concern is that dryer still takes 2 cycles to completely dry clothes. Has improved since cleaning the duct. Performed airflow test. Test failed (yellow) removed clogged lint screen. Retested. Test passed. Ran temperatures x5. Temps in range at 170. Cleaned moisture sensors. Advised about mixed loads. Also advised to clean lint screen with warm water and mild detergent to improve airflow and drying time. Dryer operates as designed.
We serviced a
KENMORE WASHER-TOPLOAD
Model 11029822801
Near Puyallup, WA 98375
Cameron M.
Job Details:
03/23/2021
"Installed previously ordered atc switch. Cycle tested, all checks good"
We serviced a
GE WASHER-TOPLOAD
Model GTW330ASK0WW
Near Garland, TX 75040
Jacob P.
Job Details:
03/23/2021
"Installed previously ordered wire harness, lid lock and control board. Test cycled, all checks ok."
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model WED8500DC3
Near Bonney Lake, WA 98391
Cameron M.
Job Details:
03/23/2021
Installed new belt and idler. Cycle tested. All checks good.
We serviced a
KENMORE DRYER-ELECTRIC
Model 11069133414
Near Plano, TX 75025
Jacob P.
Job Details:
03/23/2021
"Performed pm check on dryer, all checks ok."
We serviced a
GE WASHER-FRONT LOA
Model GTW460ASJWW
Near Dallas, TX 75217
Jacob P.
Job Details:
03/23/2021
Customer canceled appointment 3/15
We serviced a
KENMORE RANGE
Model 79046783904
Near Tacoma, WA 98404
Cameron M.
Job Details:
03/23/2021
"Installed new board, overlay and temp probe. Tested to 350. All checks good."
We serviced a
KENMORE DRYER-ELECTRIC
Model 11065132411
Near Richardson, TX 75081
Jacob P.
Job Details:
03/23/2021
"Performed pm check on dryer, fixed crushed vent. All checks ok."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB765FW2
Near McKinney, TX 75070
Jacob P.
Job Details:
03/23/2021
"Customer concern of unit leaking. Filled unit to max capacity, let agitate, drained, let spin. Checked drain hose, inlet hoses, inlet valves, drain pump, pressure hose and tub, no signs of leak. Unable to verify complaint at this time. Unit functioning as designed."
We serviced a
LG DRYER-ELECTRIC
Model DLEX8100V
Near McKinney, TX 75070
Jacob P.
Job Details:
03/23/2021
"Customer concern of dryer not heating. Found open hi limit causing no heat. Replaced hi limit and cut off. Ran air flow test, failed. Advised customer that vent from back of dryer to outside needs to be cleaned asap. Unit functioning as designed. ; used 1 6931EL3003D (Hi limit), and 1 6931EL3001F (Cut off) from stock"
We serviced a
KENMORE WASHER-TOPLOAD
Model 11025132411
Near Dallas, TX 75233
Jacob P.
Job Details:
03/23/2021
"Performed pm check on washer, all checks ok."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWX700XW0F1E2
Near Eatonville, WA 98328
Cameron M.
Job Details:
03/23/2021
Installed previously ordered control board. Cycle tested 3x all checks good.
We serviced a
KENMORE DISHWASHER
Model 66516032403
Near Spanaway, WA 98387
Cameron M.
Job Details:
03/23/2021
Installed previously ordered door seal. All checks good.
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB765FW2
Near Dallas, TX 75216
Jacob P.
Job Details:
03/23/2021
"Installed previously ordered suspension rods. Test cycled, all checks ok."
We serviced a
WHIRLPOOL WASHER-FRONT LOA
Model WTW4816FW2
Near Richardson, TX 75081
Jacob P.
Job Details:
03/23/2021
"Installed previously ordered control board. Test cycled, all checks ok."
We serviced a
GE DRYER-ELECTRIC
Model DCVH480EK0WW
Near Dallas, TX 75225
Jacob P.
Job Details:
03/23/2021
"Customer concern of long dry times, clothes coming out wet at end of cycle. Ran air flow test, failed. Removed vent and ran air flow test again, yellow. Removed lint filter and ran air flow test again, passed. Advised customer that lint screen needs to be cleaned with soap and water to wash out softener buildup and vent from back of dryer to outside needs to be cleaned. Dryer functioning as designed."
We serviced a
GE RANGE
Model JB645RK4SS
Near Richardson, TX 75081
Jacob P.
Job Details:
03/23/2021
"Installed previously ordered surface elements. Test cycled, all checks ok."
We serviced a
KENMORE WASHER-TOPLOAD
Model 11020372711
Near Plano, TX 75075
Jacob P.
Job Details:
03/23/2021
"Performed pm check on washer, all checks ok."
We serviced a
KENMORE WASHER-FRONT LOA
Model 79641162411
Near Mesquite, TX 75150
Jacob P.
Job Details:
03/23/2021
"Customer concern of unit not draining. Found drain pump impeller not moving water. Replaced drain pump. Test cycled, all checks ok. ; used 1 4681EA2001T (DRAIN PUMP) from stock"
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV56H9100EG/A2 01
Near Frisco, TX 75035
Jacob P.
Job Details:
03/23/2021
"Performed pm check, found stuck door switch causing dryer to keep running when door is open. Fixed door switch. Test cycled, all checks ok."
We serviced a
FRIGIDAIRE DISHWASHER
Model FDB750RCS0
Near Dallas, TX 75214
Jacob P.
Job Details:
03/23/2021
"Customer concern of intermittent small leak. Found door seal worn causing leak. Replaced door seal. Test cycled, all checks ok. ; used 1 154827601 (GASKET) from stock"
We serviced a
KENMORE DRYER-ELECTRIC
Model 11066132411
Near Dallas, TX 75211
Jacob P.
Job Details:
03/23/2021
"Performed pm check, all checks ok."
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW7300DW0
Near Puyallup, WA 98374
Cameron M.
Job Details:
03/23/2021
"Installed previously ordered rotor and transmission. Cycle tested, all checks good"
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE50M7450W/A3
Near Graham, WA 98338
Cameron M.
Job Details:
03/23/2021
"Customer concern is that dryer makes noise. Found seized rear roller causing noise. Replaced roller,cycle tested 3x. all checks good. ; used 1 DC97-16782A ( DRUM ROLLER) from stock"
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE50R5400V/A3
Near Seagoville, TX 75159
Jacob P.
Job Details:
03/22/2021
"Customer concern of unit not heating. Customer advised that previous tech told him that power supply cable ran to machine is not approved and needed to be fixed. Customer installed new cable and now has issues. Found power cord and outlet burnt. Checked all heating components, checks ok. Advised customer that new power cord and outlet need to be installed and possibly need an electrician to verify correct power is ran to machine. Unit functioning as designed."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB835DW5
Near Irving, TX 75061
Jacob P.
Job Details:
03/22/2021
"Customer concern of unit continually adding time on at the end of cycles, and produces an error code. Found error code f0e3 stored (overloading error). Checked suspension rods, checks good. Made sure machine is level. Ran through drain and spin empty, finished cycle. Advised customer about proper loading techniques, unit functioning as designed."
We serviced a
KENMORE WASHER-TOPLOAD
Model 11025132410
Near Dallas, TX 75216
Jacob P.
Job Details:
03/22/2021
"Performed pm check on washer, all checks ok."
We serviced a
WHIRLPOOL WASHER-FRONT LOA
Model WTW5000DW2
Near Coppell, TX 75019
Jacob P.
Job Details:
03/22/2021
"Customer concern of unit not spinning clothes out and making loud sound. Found stripped hub causing no spin. Replaced hub. Performed calibration, all checks ok. ; used 1 W10528947 (HUB) from stock"
We serviced a
GE WASHER-TOPLOAD
Model GTW330ASK3WW
Near Richardson, TX 75080
Jacob P.
Job Details:
03/22/2021
"Customer advised that they have been turning valves on and off so they can use machine while waiting for repair. Customer informed that cold water supply valve has started leaking. Found cold water valve leaking while closed, and worse when open. Installed previously ordered inlet valve. Advised customer that valve is leaking even when closed and has caused damage to wall below valve. Plumber is needed immediately. Left valves turned off."
We serviced a
MAYTAG WASHER-FRONT LOA
Model MHW5500FW1
Near Allen, TX 75013
Jacob P.
Job Details:
03/22/2021
"Customer concern of unit making burning smell and last company out hooked up hot and cold valves wrong. Inspected wire harness, control boards, rotor and stator and hoses, no signs of burns. Ran through quick diagnostic, no burning smell. Swapped inlet hoses. Unable to confirm burning smell at this time. Unit functioning as designed."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV56H9100EG/A2 01
Near Frisco, TX 75035
Jacob P.
Job Details:
03/22/2021
"Performed pm check, found stuck door switch causing dryer to keep running when door is open. Fixed door switch. Test cycled, all checks ok."
We serviced a
GE DRYER-ELECTRIC
Model DCVH480EK0WW
Near Dallas, TX 75225
Jacob P.
Job Details:
03/22/2021
"Customer concern of long dry times, clothes coming out wet at end of cycle. Ran air flow test, failed. Removed vent and ran air flow test again, yellow. Removed lint filter and ran air flow test again, passed. Advised customer that lint screen needs to be cleaned with soap and water to wash out softener buildup and vent from back of dryer to outside needs to be cleaned. Dryer functioning as designed."
We serviced a
GE WASHER-TOPLOAD
Model GTW330ASK0WW
Near Garland, TX 75040
Jacob P.
Job Details:
03/22/2021
"Installed previously ordered wire harness, lid lock and control board. Test cycled, all checks ok."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB765FW2
Near McKinney, TX 75070
Jacob P.
Job Details:
03/22/2021
"Customer concern of unit leaking. Filled unit to max capacity, let agitate, drained, let spin. Checked drain hose, inlet hoses, inlet valves, drain pump, pressure hose and tub, no signs of leak. Unable to verify complaint at this time. Unit functioning as designed."
We serviced a
GE RANGE
Model JB645RK4SS
Near Richardson, TX 75081
Jacob P.
Job Details:
03/22/2021
"Installed previously ordered surface elements. Test cycled, all checks ok."
We serviced a
KENMORE DRYER-ELECTRIC
Model 11066132411
Near Dallas, TX 75211
Jacob P.
Job Details:
03/22/2021
"Performed pm check, all checks ok."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB765FW2
Near Dallas, TX 75216
Jacob P.
Job Details:
03/22/2021
"Installed previously ordered suspension rods. Test cycled, all checks ok."
We serviced a
GE WASHER-FRONT LOA
Model GTW460ASJWW
Near Dallas, TX 75217
Jacob P.
Job Details:
03/22/2021
Customer canceled appointment 3/15
We serviced a
KENMORE WASHER-FRONT LOA
Model 11082673710
Near Dallas, TX 75217
Jacob P.
Job Details:
03/22/2021
"Performed pm check, all checks ok."
We serviced a
FRIGIDAIRE DISHWASHER
Model FDB750RCS0
Near Dallas, TX 75214
Jacob P.
Job Details:
03/22/2021
"Customer concern of intermittent small leak. Found door seal worn causing leak. Replaced door seal. Test cycled, all checks ok. ; used 1 154827601 (GASKET) from stock"
We serviced a
GE DRYER-ELECTRIC
Model GTX22EASK0WW
Near Plano, TX 75075
Jacob P.
Job Details:
03/22/2021
"Customer concern of long dry times, no light and door opens the wrong way. Ran air flow test, failed. Removed vent from back of dryer and ran air flow test again, passed. Swapped door. Advised customer that vent from back of dryer to outside needs to be cleaned and this model does not come equipped with a light. Unit functioning as designed."
We serviced a
KENMORE DRYER-ELECTRIC
Model 11065132411
Near Richardson, TX 75081
Jacob P.
Job Details:
03/22/2021
"Performed pm check on dryer, fixed crushed vent. All checks ok."
We serviced a
GE LAUNDRY CENTER
Model GUD27ESSMW
Near Dallas, TX 75204
Jacob P.
Job Details:
03/22/2021
"Customer concern of unit not spinning clothes out and clothes smelling burnt. Found motor tco errors stored. Checked motor function through service mode, all checks ok. Advised customer about proper loading techniques and deep fill option. Unit functioning as designed."
We serviced a
GE WASHER-FRONT LOA
Model GFW550SSN0WW
Near Dallas, TX 75238
Jacob P.
Job Details:
03/22/2021
"Customer concern of unit making draining sounds and running with no load. Found multiple water accessibility errors stored. Checked pressure sensor, checks ok. Inlet valves at proper pressure. Performed firmware update. All checks ok."
We serviced a
LG DRYER-ELECTRIC
Model DLEX8100V
Near McKinney, TX 75070
Jacob P.
Job Details:
03/22/2021
"Customer concern of dryer not heating. Found open hi limit causing no heat. Replaced hi limit and cut off. Ran air flow test, failed. Advised customer that vent from back of dryer to outside needs to be cleaned asap. Unit functioning as designed. ; used 1 6931EL3003D (Hi limit), and 1 6931EL3001F (Cut off) from stock"
We serviced a
GE RANGE
Model JB645RK1SS
Near Irving, TX 75061
Jacob P.
Job Details:
03/22/2021
"Installed previously ordered surface elements. Test cycled, all checks ok."
We serviced a
KENMORE WASHER-TOPLOAD
Model 11025132411
Near Dallas, TX 75233
Jacob P.
Job Details:
03/22/2021
"Performed pm check on washer, all checks ok."
We serviced a
KENMORE DISHWASHER
Model 66513543N410
Near Tacoma, WA 98405
Cameron M.
Job Details:
03/22/2021
"Customer concern is that dishwasher does not heat. Found F7 E1 (heat lockout) and F6 E4 (oversuds) errors stored. Found rinse aid cap laying in bottom of dishwasher causing unit to not use rinse aid. Found excessive amount of suds causing errors and heat Loco out. Ran several rinse cycles to clear suds. Ran diagnostic cycle to clear heat lock out. Cycle tested heater, checks good. Advised to use good quality detergent and rinse aid. Found no other issues."
We serviced a
MAYTAG WASHER-FRONT LOA
Model FAV6800AWW
Near Tacoma, WA 98418
Cameron M.
Job Details:
03/22/2021
"Installed previously ordered lid locks. Cycle tested,all checks good."
We serviced a
KENMORE DISHWASHER
Model 66516032403
Near Spanaway, WA 98387
Cameron M.
Job Details:
03/22/2021
Installed previously ordered door seal. All checks good.
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE50M7450W/A3
Near Graham, WA 98338
Cameron M.
Job Details:
03/22/2021
"Customer concern is that dryer makes noise. Found seized rear roller causing noise. Replaced roller,cycle tested 3x. all checks good. ; used 1 DC97-16782A ( DRUM ROLLER) from stock"
We serviced a
KENMORE RANGE
Model 79046783904
Near Tacoma, WA 98404
Cameron M.
Job Details:
03/22/2021
"Installed new board, overlay and temp probe. Tested to 350. All checks good."
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model GEW9250PW0
Near University Place, WA 98466
Cameron M.
Job Details:
03/22/2021
Installed new ui board. Cycle tested all checks good.
We serviced a
KENMORE WASHER-TOPLOAD
Model 11029822801
Near Puyallup, WA 98375
Cameron M.
Job Details:
03/22/2021
"Installed previously ordered atc switch. Cycle tested, all checks good"
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWX700XW0F1E2
Near Eatonville, WA 98328
Cameron M.
Job Details:
03/22/2021
Installed previously ordered control board. Cycle tested 3x all checks good.
We serviced a
LG WASHER-FRONT LOA
Model WM3250HWA
Near Graham, WA 98338
Cameron M.
Job Details:
03/22/2021
"Customer concern is that washer is not balanced and wants door boot installed. Installed custo,Customer, provided door boot (no part warranty) and leveled washer. Cycle tested. All checks good. Advised to keep door boot and glass clean."
We serviced a
KENMORE DRYER-ELECTRIC
Model 11075962401
Near Enumclaw, WA 98022
Cameron M.
Job Details:
03/22/2021
Installed new timer. Cycle tested. All checks good.
We serviced a
MAYTAG WASHER-FRONT LOA
Model MVWC465HW2
Near Buckley, WA 98321
Cameron M.
Job Details:
03/22/2021
Installed new lid lock. Cycle tested. All checks good.
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW7300DW0
Near Puyallup, WA 98374
Cameron M.
Job Details:
03/22/2021
"Installed previously ordered rotor and transmission. Cycle tested, all checks good"
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE50R5400V/A3
Near Seagoville, TX 75159
Jacob P.
Job Details:
03/19/2021
"Customer concern of unit not heating. Customer advised that previous tech told him that power supply cable ran to machine is not approved and needed to be fixed. Customer installed new cable and now has issues. Found power cord and outlet burnt. Checked all heating components, checks ok. Advised customer that new power cord and outlet need to be installed and possibly need an electrician to verify correct power is ran to machine. Unit functioning as designed."
We serviced a
KENMORE WASHER-TOPLOAD
Model 11025132410
Near Dallas, TX 75216
Jacob P.
Job Details:
03/19/2021
"Performed pm check on washer, all checks ok."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB835DW5
Near Irving, TX 75061
Jacob P.
Job Details:
03/19/2021
"Customer concern of unit continually adding time on at the end of cycles, and produces an error code. Found error code f0e3 stored (overloading error). Checked suspension rods, checks good. Made sure machine is level. Ran through drain and spin empty, finished cycle. Advised customer about proper loading techniques, unit functioning as designed."
We serviced a
KENMORE DISHWASHER
Model 66513543N410
Near Tacoma, WA 98405
Cameron M.
Job Details:
03/19/2021
"Customer concern is that dishwasher does not heat. Found F7 E1 (heat lockout) and F6 E4 (oversuds) errors stored. Found rinse aid cap laying in bottom of dishwasher causing unit to not use rinse aid. Found excessive amount of suds causing errors and heat Loco out. Ran several rinse cycles to clear suds. Ran diagnostic cycle to clear heat lock out. Cycle tested heater, checks good. Advised to use good quality detergent and rinse aid. Found no other issues."
We serviced a
MAYTAG WASHER-FRONT LOA
Model FAV6800AWW
Near Tacoma, WA 98418
Cameron M.
Job Details:
03/19/2021
"Installed previously ordered lid locks. Cycle tested,all checks good."
We serviced a
WHIRLPOOL WASHER-FRONT LOA
Model WTW5000DW2
Near Coppell, TX 75019
Jacob P.
Job Details:
03/19/2021
"Customer concern of unit not spinning clothes out and making loud sound. Found stripped hub causing no spin. Replaced hub. Performed calibration, all checks ok. ; used 1 W10528947 (HUB) from stock"
We serviced a
GE WASHER-TOPLOAD
Model GTW330ASK3WW
Near Richardson, TX 75080
Jacob P.
Job Details:
03/19/2021
"Customer advised that they have been turning valves on and off so they can use machine while waiting for repair. Customer informed that cold water supply valve has started leaking. Found cold water valve leaking while closed, and worse when open. Installed previously ordered inlet valve. Advised customer that valve is leaking even when closed and has caused damage to wall below valve. Plumber is needed immediately. Left valves turned off."
We serviced a
MAYTAG WASHER-FRONT LOA
Model MHW5500FW1
Near Allen, TX 75013
Jacob P.
Job Details:
03/19/2021
"Customer concern of unit making burning smell and last company out hooked up hot and cold valves wrong. Inspected wire harness, control boards, rotor and stator and hoses, no signs of burns. Ran through quick diagnostic, no burning smell. Swapped inlet hoses. Unable to confirm burning smell at this time. Unit functioning as designed."
We serviced a
KENMORE DISHWASHER
Model 66516032403
Near Spanaway, WA 98387
Cameron M.
Job Details:
03/19/2021
Installed previously ordered door seal. All checks good.
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV56H9100EG/A2 01
Near Frisco, TX 75035
Jacob P.
Job Details:
03/19/2021
"Performed pm check, found stuck door switch causing dryer to keep running when door is open. Fixed door switch. Test cycled, all checks ok."
We serviced a
GE DRYER-ELECTRIC
Model DCVH480EK0WW
Near Dallas, TX 75225
Jacob P.
Job Details:
03/19/2021
"Customer concern of long dry times, clothes coming out wet at end of cycle. Ran air flow test, failed. Removed vent and ran air flow test again, yellow. Removed lint filter and ran air flow test again, passed. Advised customer that lint screen needs to be cleaned with soap and water to wash out softener buildup and vent from back of dryer to outside needs to be cleaned. Dryer functioning as designed."
We serviced a
GE WASHER-TOPLOAD
Model GTW330ASK0WW
Near Garland, TX 75040
Jacob P.
Job Details:
03/19/2021
"Installed previously ordered wire harness, lid lock and control board. Test cycled, all checks ok."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB765FW2
Near McKinney, TX 75070
Jacob P.
Job Details:
03/19/2021
"Customer concern of unit leaking. Filled unit to max capacity, let agitate, drained, let spin. Checked drain hose, inlet hoses, inlet valves, drain pump, pressure hose and tub, no signs of leak. Unable to verify complaint at this time. Unit functioning as designed."
We serviced a
GE RANGE
Model JB645RK4SS
Near Richardson, TX 75081
Jacob P.
Job Details:
03/19/2021
"Installed previously ordered surface elements. Test cycled, all checks ok."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE50M7450W/A3
Near Graham, WA 98338
Cameron M.
Job Details:
03/19/2021
"Customer concern is that dryer makes noise. Found seized rear roller causing noise. Replaced roller,cycle tested 3x. all checks good. ; used 1 DC97-16782A ( DRUM ROLLER) from stock"
We serviced a
KENMORE RANGE
Model 79046783904
Near Tacoma, WA 98404
Cameron M.
Job Details:
03/19/2021
"Installed new board, overlay and temp probe. Tested to 350. All checks good."
We serviced a
KENMORE DRYER-ELECTRIC
Model 11066132411
Near Dallas, TX 75211
Jacob P.
Job Details:
03/19/2021
"Performed pm check, all checks ok."
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model GEW9250PW0
Near University Place, WA 98466
Cameron M.
Job Details:
03/19/2021
Installed new ui board. Cycle tested all checks good.
We serviced a
KENMORE WASHER-TOPLOAD
Model 11029822801
Near Puyallup, WA 98375
Cameron M.
Job Details:
03/19/2021
"Installed previously ordered atc switch. Cycle tested, all checks good"
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWX700XW0F1E2
Near Eatonville, WA 98328
Cameron M.
Job Details:
03/19/2021
Installed previously ordered control board. Cycle tested 3x all checks good.
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB765FW2
Near Dallas, TX 75216
Jacob P.
Job Details:
03/19/2021
"Installed previously ordered suspension rods. Test cycled, all checks ok."
We serviced a
GE WASHER-FRONT LOA
Model GTW460ASJWW
Near Dallas, TX 75217
Jacob P.
Job Details:
03/19/2021
Customer canceled appointment 3/15
Near DuPont, WA 98327
Cameron M.
Job Details:
03/15/2021
WASHER-TOPLOAD MAYTAG MVWB955FW0
Installed previously ordered main control. Cycle tested in rapid wash and service cycle. Calibrated control. All checks good at this time.
Near DuPont, WA 98327
Cameron M.
Job Details:
03/15/2021
WASHER-TOPLOAD MAYTAG MVWB765FC3
Installed new transmission. Cycle tested. All checks good.
Near Steilacoom, WA 98388
Cameron M.
Job Details:
03/15/2021
RANGE GE JBP90WW1WW
Installed new door lock assembly. All checks good.
Near Gig Harbor, WA 98335
Cameron M.
Job Details:
03/15/2021
DRYER-ELECTRIC LG DLEX7700VE
"Customer concern is that dryer takes to long dry clothes. Preformed an airflow test, failed. Cleaned moisture sensor. Unit has good heat but poor airflow. Found no mechanical issues dryer Preformed per design. Found air duct behind unit partially crushed. Advised customer airvent needs to be cleaned asap."
Near Garland, TX 75044
Jacob P.
Job Details:
03/15/2021
DISHWASHER KENMORE 66513712K601
"Customer concern that unit runs continuously. Checked turbidity sensor, clean. Customer advised cycles normally run over an hour. Advised customer that cycles taking over an hour is normal. Quick cycle will run faster but has lower washing efficiency. Unit functioning as designed."
Near Dallas, TX 75224
Jacob P.
Job Details:
03/15/2021
WASHER-TOPLOAD MAYTAG MVWX655DW1
"Installed previously ordered control board. Test cycled, all checks ok."
Near University Place, WA 98466
Cameron M.
Job Details:
03/15/2021
WASHER-TOPLOAD MAYTAG MAV6057AWW
"Installed new thrust bearing and belt. Cycle tested, all checks good."
Near Tacoma, WA 98404
Cameron M.
Job Details:
03/15/2021
DISHWASHER MAYTAG MDB8951BWS
Installed new console and door latch. Cycle tested. All checks good.
Near Spanaway, WA 98387
Cameron M.
Job Details:
03/15/2021
RANGE LG LRE3083ST/00
"Installed new control board and display board. Cycle tested all all cooktop burners,warming burner and oven elements. All checks good."
Near DuPont, WA 98327
Cameron M.
Job Details:
03/15/2021
WASHER-TOPLOAD MAYTAG MVWB765FC3
Customer concern is that washer making noise after transmission replacement. Found clutch disc tapping magnetic clutch housing causing noise. Shifted housing 1mm forward. Cycle tested. All checks good.
Near Lakewood, WA 98498
Cameron M.
Job Details:
03/15/2021
DISHWASHER SAMSUNG DW80M2020US/AA
Installed new inlet valve. Cycle tested. Found door seal leaking. Seal installed improperly. Installed seal properly. Cycle tested. No leaks. All checks good.
Near Gig Harbor, WA 98335
Cameron M.
Job Details:
03/15/2021
WASHER-TOPLOAD KENMORE 11022332510
Customer concern is that unit does not finish cycle. Found F8e1 (long fill) error stored. Cleaned inlet valve. Cycle tested. Washer working properly. Inlet valve screen is damaged and should be replaced. Needs new inlet valve. Declined new valve at this time.