DRYER-ELECTRIC WHIRLPOOL WED5300VW0 "found unit had crushed vent behind dryer causing poor airflow and long dry times. customer shortened vent, cycle tested, all checks good."

DRYER-ELECTRIC SAMSUNG DV42H5000EW "found unit had an open heating element causing no heat condition. replaced heating element, cycle tested, all checks good.no vent on dryer, customer said she is going to take care of that.dryer stacked without the stacking hardware installed.240v outlet hanging out of wall.; used 1 DC97-14486A (ELEMENT ASSEMBLY) from stock"

DISHWASHER GE GLD5560L15SS "found spray arms filled with debris causing them to not move during wash making dishwasher unable to clean dishes. needs new spray arms.advised customer parts are on backorder.; ordrng 1 WD22X10044 (lower spray arm) and 1 WD22X10046 (middle spray arm) and 1 WD22X10084 (upper spray arm), warned against exceeding $250.00 pre-auth limit"

WASHER-FRONT LOA LG WM0532HW "main pcb sent by AHS does not match the one is the washer. some of the wire conections do not match up. found a different part number on the board in the unit. called AHS to inform them of difference in part. they are resubmitting to their research department to try to track down 6871EC1081B which is also NLA.; rqstng P&A on 1 6871EC1081B (main pcb), warned against exceeding $250.00 pre-auth limit"

WASHER-FRONT LOA MAYTAG MAH3000AWW "installed wax motor and spin switch, cycle tested, all checks good. unit goes into spin everytime."

DRYER-ELECTRIC WHIRLPOOL WED6400SW0 "found unit had a seized idler pulley causing squeeling and drag on motor. replaced idler, cycle tested, all checks good.; used 1 8547174V (PULLEY-IDR) from stock"

DISHWASHER MAYTAG WDT730PAHZ0 CUSTOMER COMPLAINT THAT DISHWASHER DOES NOT RUN. FOUND 105V TO WASH PUMP. NEEDS TO BE 120V. NEEDS NEW MAIN BOARD. ALSO FOUND FOUND WASH PUMP OHMS OUT OF RANGE PER WHIRLPOOL TECH GUIDE. NEEDS NEW WASH PUMP. ALSO FOUND OPEN HEATER. NEEDS NEW HEATER. DISHWASHER INSTALLED BELOW FLOOR LEVEL. HAD TO LOWER DISHWASHER. ADVISED CUSTOMER TO NOT USE DISHWASHER AS A DRYING RACK WHILE AWAITING REPAIR.; ordrng 1 W11084656 (motor-pump) and 1 WPW10538166 (grommet) and 1 W11305308 (cntrl-elec) and 1 W10518394 (heater)

WASHER-FRONT LOA KENMORE 79641373211 "found unit has a pinhole in drain hose causing unit to leak. needs new drain hose.resch for 3/21, 1-5; ordrng 1 5215ER2002G (drain hose)"

DRYER-ELECTRIC WHIRLPOOL WED8500DC1 "CUSTOMER COMPLAINT DRYER SHUTS DOWN EARLY AND DOESNT DRY CLOTHES.CYCLED TESTED TEMPS 3 TIMES, RAN AIR FLOW CHECK,INSPECTED DUCT FOR OBSTRUCTIONS, CLEANED AND CALIBRATED MOISTURE SENCERS, ALL CHECKS OK. ADVISED CUSTOMER TO CALL BACK IF PROBLEM CONTUINES."

DRYER-ELECTRIC WHIRLPOOL WED7300XW0 "installed board, cycle tested and found dryer operating normally but power supply is losing power intermitently. one leg droping from 120v to 6v causing dryer to run intermitently. wall outlet good. electrician is needed for power supply issue. called AHS and advised they need to send electrician."

DISHWASHER WHIRLPOOL WDF310PAAS4 INSTALLED NEW HEATING ELEMENT. CYCLE TESTED. ALL OPS GOOD.

DRYER-ELECTRIC GE DCVH480EK0WW "found unit has a seized idler that screeches once it breaks free and turns. needs new idler assembly.advised customer they are in need of a vent cleanresch for 3/19, 8-12; ordrng 1 WE49X28031 (IDLER BRACKET AND BEARING)"

WASHER-FRONT LOA SAMSUNG WV55M9600AV/A5 02 "installed display boards, cycle tested, all checks good."

WASHER-FRONT LOA LG WM3470HVA "FOUND BOTH THE HOT AND COLD INLET VALVES LEAKING. REPLACED INLET VALVES. CYCLE TESTED. NO OTHER LEAKS FOUND. LEFT FAILED PARTS AS THEY CAUSED A WATER LEAK; used 1 5220FR2075L (INLET VALVE-COLD), and 1 5220FR2006H (INLET VALVE (HOT)) from stock"

WASHER-FRONT LOA ELECTROLUX EFLW317TIW1 "unit has a seized drain pump. receiving 120v but no motor movement or hum. needs new drain pump.resch for 3/21, 8-12; rqstng P&A on 1 5304505209 (drain pump)"

DISHWASHER KENMORE 66516293400 "DOOR POPPING OPEN DURING WASH. FOUND DOOR HIGES BENT CAUSING DOOR TO NOT CLOSE PROPERLY. ALSO FOUND DOOR SPRING ROLLERS BROKEN. ALSO FOUND CONSOLE BROKEN CAUSING DOOR TO BE FLIMSY. NEEDS NEW HINGES, SPRING ROLLERS, AND CONSOLE.; rqstng P&A on 1 WP8534853 (door hinge) and 1 WP8534854 (door hinge)"

WASHER-TOPLOAD MAYTAG MVWX655DW1 FOUND FABRIC SOFTENER SWITCH STEM BROKEN OFF. NEEDS NEW SWITCH AND KNOB; ordrng 1 WPW10562155 (knob) and 1 W11197418 (switch-cyc)

DRYER-ELECTRIC SAMSUNG DV45H7000EW/A2 02 "DRYER WILL NOT RUN, REMOVED SOCK FROM BLOWER WHEEL CAUSING BIND ON MOTOR. CYCLE TESTED. ALL CHECKS OK.. ADVISED TO NOT RUN DRYER WITHOUT LINT SCREEN IN PLACE."

RANGE HOTPOINT RB540SH2SA "CUSTOMER COMPLAINT THAT RIGHT FRONT BURNER HAS MELTES WIRES AND OVEN TEMP SWITCH TURNS ITSELF ON. NEEDS NEW TERMINAL BLOCK, BURNER, THERMOSTAT SWITCH AND KNOB.; rqstng P&A on 1 WB03T10167 (surface element) and 1 WB17T10006 (block insulator) and 1 WB03K10173 (range thermostat kno) and 1 WB20K10026 (thermostat)"

WASHER-FRONT LOA SAMSUNG WF45K6200AW/A2 "installed door lock, cycle tested, all checks good.advised customer he may want to reinforce floor under weasher as washer on pedistal shakes the entire room"

DRYER-ELECTRIC LG DLG7188RM "installed drum and rollers, cycle tested, all checks good."

WASHER-TOPLOAD MAYTAG MVWX655DW "unable to find any issues with washer. customer stated they had an out of balance load that made a loud bang then shut down washer and they found black stuff in washer. ran full diagnostics, rinse and spin and recalibration cycle with no issues. advised customer on loading properly balanced and sized loads. showed customer sound dampening foam pads that have been rubbed by out of balance tub and pieces ended up in washer. all checks good."

DRYER-ELECTRIC SAMSUNG DV42H5000EW/A3 04 "CUSTOMER COMPLAINT OF NO HEAT IN UNIT. FOUND OPEN HEATING ELEMENT CAUSING NO HEAT.REPLACED HEATING ELEMENT. TEST CYCLED, ALL CHECKS OK.; used 1 DC97-14486A (ELEMENT ASSEMBLY) from stock"

RANGE SAMSUNG NE59J3420SS/AA INSTALLED NEW TOUCHPAD. 5 AND KITCHEN TIMER STILL NOT WORKING. PER SAMSUNG TECH ASSISTS. NEED TO REPLACE MAIN BOARD. MAIN BOARD IS FACTORY BACK ORDERED WITH NO ETA PER SAMSUNG. ORDERING REMAN. BOARD.; ordrng 1 DE92-03045F (main pcb)

WASHER-TOPLOAD WHIRLPOOL WTW8800YC1 FOUND DRAIN PUMP HAS DEAD SPOT CAUSING PUMP TO NOT RUN. NEEDS NEW PUMP; ordrng 1 WPW10409079 (pump-water)

DISHDRAWER FISHER PAYKEL DD24DCTX7 found top drawer not able to recognize door closing and will not start cycle. needs new control with light pipe.lower drawer has a expanded rotor causing noise and drag while rotor is spinning. needs new rotor.units drain is conected directly to plumbing and after conection there is a back up. pressure built up in plumbing and water coming out of external plumbing airgap. advised this issue needs a plumber.first american do do a cost comparison for replacement. will advise us if they want to go forward with repairs.auth for labor - 3387832; rqstng P&A on 1 523725USP (MOD CTRL 525 P7 DD60 120V USP) and 1 528276 (light pipe) and 1 524285P (rotor)

WASHER-TOPLOAD MAYTAG MAV4057AWW "LEAKING. NOT WASHING. WONT START. FOUND LEAK IS STAND PIPE BACKING UP AND OVERFLOWING. WHEN WASHER DRAINS. KITCHEN SINK FILLS UP. ADVISED A PLUMBER IS NEEDED TO RESOLVE THAT ISSUE. NOT AGITATING DUE TO BURNED OUT MOTOR. ALSO HAS LOOSE BELT. WHEN IT SPINS, THE CABINET SHAKES. FOUND CABINET SCREWS NOT SECURING IT TO THE BASE, NEEDS NEW SCREWS. ALSO FOUND BROKEN CONSOLE CLIPS CAUSING CONSOLE TO COME OFF. NEEDS NEW CONSOLE. UNABLE TO LEVEL WASHER AS REAR LEVELER ASSEBLY IS SEIZED. NEEDS REAR LEVELER. ALSO ADVISED THAT FILL HOSE IS ABOUT TO BURST. ADVISED TO REPLACE HOSES ASAP.; rqstng P&A on 1 WP21001950 (motor-drve) and 1 WP22003483 (belt) and 1 27001110 (CONSOLE) and 9 213007 (screw#12 pozi-drive)s and 1 21001754 (LEVELER BAR) and 2 35-2046 (bracket- s)s and 2 35-2052 (pin,stabilizer)s and 2 WP22004469 (leg foot)s"

WASHER-TOPLOAD SAMSUNG WA52M7750AV/A4 01 "COMPLAINT OF 'UB' ERROR AND NOT FINISHING LOAD. CYCLE TESTED EMPTY AND WITH A LOAD. ALL OPS OK AT THIS TIME. SUSPENSION RODS ALL CHECK GOOD. BASKET HAS GOOD ALIGNMENT. ADVISED TO WASH BEDDING ON BEDDING CYCLE. ADVISED THAT SOME LOADS WILL PRODUCE UB ERROR IS WASHER CAN NOT SELF CORRECT LOAD, AND WILL NEED TO BE REDISTRIBUTED. ORDERING NEW WASHPLATE CAP DIRECT TO CUSTOMER. CURRENT CAP IS BROKEN.; ordrng 1 DC66-00887B (WASHPLATE CAP)"

OVEN-WALL FISHER PAYKEL FPOS302 "customer complained of other oven smoking while in use. found convection element covered in grease and broken. needs new convection element.resch for 3/18, 10-2 50$ discount on labor for repeat customer/second appliance; ordrng 1 547680 (element fan ego 20.4)"

WASHER-FRONT LOA WHIRLPOOL WTW4900BW0 "found unit has a loud and leaking gearcase causing poor and noisey operation. needs new gearcase.resch for 3/18, 1-5auth - 508ydclauth -; ordrng 1 W11035747 (gearcase)"

WASHER-TOPLOAD MAYTAG MVWX655DW1 "F9 E1 LONG DRAIN F0 E2 OVER SUDS F0 E5 UNBALANCED LOAD. CUSTOMER COMPLAINT OF UNIT GETTING STUCK IN DRAIN CYCLE. FOUND UNIT DRAINING VERY SLOWLY. FOUND SOCK STUCK IN DRAIN HOSE CAUSING SLOW DRAIN. REMOVED SOCK. TEST CYCLED, ALL CHECKS OK."

DRYER-ELECTRIC WHIRLPOOL SEDS800JQ0 "COMPLAINT THAT DRUM IS NOT TURNING. FOUND BROKEN BELT CAUSING DRUM TO NOT TURN. REPLACED BELT AND IDLER PULLEY. CYCLE TESTED. ALL OPS GOOD.; used 1 WP691366 (PULLEY-IDR), and 1 341241 (BELT,DRIVE) from stock"

WASHER-FRONT LOA WHIRLPOOL WFW92HEFW0 "found units pressure hose came off tub causing unit to pour water onto floor. re clamped hiose to tub, cycle tested, all checks giood.customer stated previous company replaced tub."

WASHER-TOPLOAD SAMSUNG WA48J7770AW "found washplate loose causing abnormal noise during wash cycle. tightened washplate bolt, cycle tested, all checks good. no other noises."

DRYER-ELECTRIC MAYTAG DE9800 "installed pulley and rollers, cycle tested, all checks good.light bulb broke as i removed front panel, replaced bulb.; used 1 7C7 (LAMP 7C7) from stock"

WALL OVEN FISHER PAYKEL FPOS302 "installed tempo probe, cycle tested, all checks good.customer woulkd like a phsical copy of invoice mailed to her"

DRYER-ELECTRIC WHIRLPOOL LER7646AN0 "CUSTOMER COMPLAINT THAT DRYER DOESN'T TURN ON. FOUND OPEN THERMAL FUSE CAUSING NO OPERATION. REPLACED THERMAL FUSE. CYCLE TESTED TEMPS IN REGULAR CYCLE AND AIR FLUFF, TESTED AIR FLOW, ALL CHECKS OK.; used 1 WP3392519 (FUSE-THRML) from stock"

DISHWASHER WHIRLPOOL WDT970SAHZ0 INSTALLED ORDERED VAVLE TEST CYCLED ALL CHECKES OK LEFT FAILED PART WITH CUSTOMER.

DISHWASHER LG LDT7797BD COMPLAINT THAT DOOR IS NOT ALIGNED. FOUND RIGHT SIDE OF DISHWASHER TOO LOW CAUSING MISALIGNMENT. LEVELED DISHWASHER. ALL CHECKS OK

WALL OVEN DCS WOSV2-30 model - wosv2-30serial - lhg381344pc- 71165-acalled customer who was able to locate correct model and serial in his paperwork

DISHWASHER SAMSUNG DW80J3020US/AA COMPLAINT THAT DISHWASHER IS LOUD WHEN WASHING AND DISPENSER NOT OPENING. FOUND WASH PUMP HAS BAD BEARINGS CAUSING LOUD WASH AND DISPENSER SPRING LOOSE CAUSING DOOR TO NOT OPEN. NEEDS NEW SUMP ASSEMBLY AND DISPENSER ASSEMBLY.; ordrng 1 DD82-01246A (sump assembly) and 1 DD59-01001A (DISPENSER)

WASHER-FRONT LOA SAMSUNG WF337AAG/XAA "FOUND BASKETSPINNER SUPPORT SNAPPED CAUSIING BASKET TO SCRAPE DOOR BOOT AND CAUSE SMOKE. NEEDS NEW REAR TUB, BASKET ASSEMBLY, TUB SEAL AND DOOR BOOT.; rqstng P&A on 1 DC97-12957A (REAR TUB) and 1 DC69-00804A (TUB SEAL) and 1 DC97-12604A (BASKET) and 1 DC64-00802A (door-diaph)"

RANGE WHIRLPOOL WGE745C0FS00 COMPLAINT THAT NO ELEMENTS WORK AFTER POWER OUTAGE. FOUND L1 TO N 120V L2 TO N 50V ADVISED THEY NEED AN ELECTRICIAN AS THEY HAVE A POWER SUPPLY ISSUE.

WASHER-FRONT LOA WHIRLPOOL WFW92HEFW0 AFTER LAST REPAIR (PUMP CLEAN) WASHER PRODUCED ERROR CODE AND DID NOT COMPLETE CYCLE. UNIT HAS BEEN USED SEVERAL TIMES SINCE WITH NO ISSUES. CYCLE TESTED IN DIAG CYCLE AND QUICK WASH. ALL OPS OK AT THIS TIME. ADVISED TO CALL IF ISSUES RETURN.

RANGE WHIRLPOOL WGE745C0FS00 INSTALLED NEW UPPER DOOR FRAME AND KNOB. ALL CHECKS OK.

OTHER SAMSUNG RF263TEAESG/AA ICE MAKER WORKING AT AND PRIOR TO SERVICE. MINIMAL ICING IN THE ICE ROOM. ADVISED IF ISSUE RETURNS. WE WOULD LIKELY NEED TO REPLACE ICE MAKER SERVICE KIT.

DRYER-ELECTRIC GE DVL223EB4WW "CUSTOMER COMPLAINT THAT UNIT IS MAKING LOUD CLICKING SOUND. FOUND PIECE OF FOAM IN BLOWER HOUSING. REMOVED FOAM FROM HOUSING. TEST CYCLED, ALL CHECKS OK. PERFORMED AIR FLOW TEST WHEN CUSTOMER ADVISED HE ACCIDENTALLY DROPPED BRUSH DOWN VENT. AIR FLOW TEST FAILED, ADVISED CUSTOMER HE WILL NEED AN HVAC COMPANY TO COME CLEAN VENTS."

RANGE SAMSUNG NE59N6630SS/AA "CUSTOMER COMPLAINT OF UNIT HAVING A WEIRD SMELL AND A LOUD BANG AT THE BEGINNING OF USE. ADVISED BANG AT THE BEGINNING IS HEAT ABSORBING INTO THE METALS AND THE CASE SHIFTING. UNABLE TO DETECT ANY ABNORMAL SMELLS. CHECKED ALL WIRE HARNESS, CONTROL BOARDS AND ELEMENT FOR ANY BURNS OR LOOSE CONNECTIONS. ALL CHECKS OK."

WASHER-TOPLOAD SAMSUNG WA52M7750AV/A4 INSTALLED NEW MAIN BOARD AND SUSPENSION RODS. CYCLE TESTED WITH LOAD. ALL CHECKS OK

WASHER-FRONT LOA WHIRLPOOL WFW9640XW00 "CUSTOMER COMPLAINT OF UNIT LEAKING FROM DOOR SEAL. FOUND SMALL TEAR IN FRONT OF DOOR BOOT CAUSING LEAK. NEEDS NEW DOOR BOOT. SUBBD ONLINE FOR AUTH; rqstng P&A on 1 WP8182119 (bellow), warned against exceeding $250.00 pre-auth limit, states that autho needed"

DRYER-ELECTRIC ADMIRAL ADE7005AYW CUSTOMER COMPLAINT THAT UNIT WILL NOT POWER ON. FOUND ONE LEG FROM POWER CORD TO DRYER BURNT UP CAUSING ONLY 120V TO UNIT. NEEDS NEW TERMINAL BLOCK AND POWER CORD. CUSTOMER TO SUPPLY POWER CORD.; ordrng 1 WP61923 (block- ter)

OTHER KENMORE 59672003016 "INSTALLED PREVIOUSLY ORDERED ICE MAKER. RAN THROUGH TEST HARVEST, ALL CHEKCKS OK."

WASHER-TOPLOAD KENMORE 11091278100 "CUSTOMER COMPLAINT OF LEAK UNDERNEATH UNIT. FOUND WORN SEALS IN WATER PUMP. REPLACED WATER PUMP. TEST CYCLED, ALL CHECKS OK. LEFT FAILED PART WITH CUSTOMER; used 1 WP3363394 (PUMP-WATER) from stock"

WASHER-TOPLOAD LG WT7200CV "CUSTOMER COMPLAINT THAT UNIT WAS SHAKING AND BANGING AROUND A LOT. HAS USED IT SINCE THEN AND IT HAS RAN OKAY, BUT THIS ISN'T THE FIRST TIME IT'S HAPPENED, SO WOULD LIKE MACHINE CHECKED OUT. RAN THROUGH SPIN CYCLE, CHECKED SUSPENSION RODS, CHECKED ROTOR TIGHTNESS, TEST CYCLED WITH LOAD, ALL CHECKS OK. ADVISED CUSTOMER THAT IF MACHINE DOES GO OUT OF BALANCE, IT WILL TRY TO REBALANCE ITSELF, SO SHAKING CAN BE NORMAL."

DRYER-ELECTRIC KENMORE 11061202011 "CUSTOMER COMPLAINT THAT DRYER TRIPS BREAKER UPON STARTUP. CYCLE TESTED DRYER, DRYER RUNNING FINE CURRENTLY. TESTED VOLTAGE TO UNIT, TESTED AMP DRAW, TESTED THROUGH ALL CYCLES, INSPECTED WIRE HARNESS FOR ANY BREAKS, ALL CHECKS OK. ADVISED CUSTOMER OF POSSIBLE WEAK BREAKER. ADVISED THEY WILL NEED AN ELECTRICIAN TO COME OUT AND INSPECT/REPLACE BREAKER. CALLED IN FOR AUTH. AUTH CODE CCCN3X332214."

RANGE WHIRLPOOL WFE515S0ES0 customer stated that when front right burner is used the breaker for the living room will trip. turned on all burners to high and bake element. unit never draws more thn 45 amps and never trips breaker. tried all burners individually with each running at about 12 amps. jiggled power cord and shook range and wiring with all elements on with no isssues. oven breaker is not tripping. ooven is on dedicated circuit and can not trip living room breaker. AHS will need to send an electrician.auth - 110abbl

WASHER-FRONT LOA MAYTAG MAH3000AWW "found wax motor of door lock not engaging spin switch causing no spin condition. needs new wax motor and spin engage switchauth - cccn3x3153b9resch for 3/14, 8-12; ordrng 1 WP22002119 (motor-wax) and 1 WP22002162 (switch-dor)"

DISHWASHER MAYTAG MDB4621AWW0 "installed door switch kit and latch parts, cycle tested, all checks good. unit no longer shuts off during cycle even if door is jostled."

RANGE MAYTAG MER5755QAS "unit has a sticking relay on main control causing unit to not heat to proper temp. needs new control.advised customer to call in recall to AHS. advised customer once we receive recall we can get part ordered and get her rescheduled.; rqstng P&A on 1 WP5701M719-60 (CNTRL-ELEC), states that autho needed"

RANGE KENMORE n/a "COMPLAINT THAT START, STOP AND BROIL BUTTONS NOT WORKING. NEEDS NEW MAIN BOARD AND OVERLAY. UNABLE TO LOCATE MODEL NUMBER OR SERIAL PLATE. UNABLE TO REPAIR UNIT. COLLECTED 75.00 DEDUCTIBLE VIA CHECK. ORHP TO REPLACE RANGE. AUTH XLI693"

DRYER-ELECTRIC KENMORE 11069422801 "COMPLAINT THAT DRYER RUNS PAST CYCLE TIME AND DOES NOT HEAT PROPERLY. FOUND FAILED TIMER CONTACTS CAUSING UNIT TO NOT HEAT PROPERLY. DOOR CATCH IS BROKEN AND DOOR HINGES ARE WORN OUT CAUSING DOOR TO NOT CLOSE PROPERLY. ALSO FOUND WORN DRUM ROLLERS, BELT AND IDLER PULLEY.; rqstng P&A on 1 WPW10185976 (timer) and 1 279570 (catch door dryer) and 2 WPW10362431 (hinge)s and 1 341241 (belt,drive) and 1 WP691366 (pulley-idr) and 1 349241T (support,roller)"

WASHER-FRONT LOA SAMSUNG WV55M9600AV/A5 02 "found units controls unresponsive causing unit to be unusable. as per samsung, user interface boards will need to be replaced.advised customer part on backorder.subbe online foe auth; rqstng P&A on 1 DC92-01993A (display board) and 1 DC92-01992A (display board), warned against exceeding $250.00 pre-auth limit"

RANGE FRIGIDAIRE FGF348KCM COMPLAINT THAT OVEN TAKES AN HOUR TO HEAT. FOUND FAILED BAKE IGNITOR CAUSING UNIT TO NOT IGNITE. REPLACED IGNITOR. CYCLE TESTED. ALL CHECKS OK.; used 1 WB13K21 (OVEN IGNITER-12' LEAD W/NUTS) from stock

DRYER-ELECTRIC SAMSUNG DV48J7700EW/A2 01 "found unit had a melted idler pulley causing unit to not tumble. replaced idler pulley, cycle tested, all checks good.; used 1 DC93-00634A (IDLER ASSEMBLY) from stock"

WASHER-FRONT LOA SAMSUNG WA50F9A8DSP/A2 "unable to get unit to produce any abnormal noise. tested all functions of washer, all checks good."

DRYER-ELECTRIC WHIRLPOOL WED9200SQ1 "installed control, cycle tested, all checks good. unit now cycling heat normally."

DRYER-ELECTRIC SAMSUNG DV45H7000EW/A2 02 "found unit had a worn roller and seized idler pulley. replaced roller and idler, cycle tested, all checks good.auth - 3382656; used 1 DC93-00634A (IDLER ASSEMBLY), and 2 DC97-16782A (DRUM ROLLER) from stock"

DISHWASHER WHIRLPOOL WDF310PAAS4 NOT HEATING AND NOT WASHING WELL. FOUND A LOT OF SUDS IN DISHWASHER. ALSO FOUND OPEN HEATING ELEMENT CAUSING NO HEAT. NEEDS NEW ELEMENT. ADVISED TO RUN CLEAN CYCLES AND USE LESS DETERGENT.; ordrng 1 W10518394 (heater) and 2 WPW10503548 (retainer)s

DISHWASHER ELECTROLUX LGHD2433KM0 "in stalled control and door latch. cycle tested on normal with all options selected, ran for 30 minutes with no issues. customer stated unit would shut down after 10 minutes. all checks good."