We serviced a
MAYTAG WASHER-FRONT LOA
Model MHW3505FW0
Near Fircrest, WA 98466
Cameron M.
Job Details:
08/11/2021
"Customer concern is that washer started leaking from rear left corner after preforming self clean cycle. Found evidence of over suds condition, causing unit to leak. Cycle tested unit 3x found no mechanical issues. Unit operating as designed. Advised customer on regular clean cycle intervals ."
We serviced a
MAYTAG DRYER-ELECTRIC
Model MEDX655DW1
Near Puyallup, WA 98373
Cameron M.
Job Details:
08/11/2021
Customer concern is that dryer takes multiple cycles to dry clothes. Preformed airflow test passed (green). Preformed temperature checks in range. Cleaned and calibrated moisture sensors. Found no mechanical issues at time of service. Unit operating as designed.
We serviced a
GE RANGE
Model JB860SJ3SS
Near Puyallup, WA 98373
Branden W.
Job Details:
08/11/2021
"Customer concern is that after power cycle at breaker, range does not operate any elements. Found only 120vac supplied to range at wall plug. Reset breaker for range several times. Still only 120v. Advised an electrician is needed to restore 240v to range."
We serviced a
FRIGIDAIRE DISHWASHER
Model FPHD2485NF1A
Near McKinney, TX 75071
Jacob P.
Job Details:
08/11/2021
"Customer concern of unit not starting. Advised customer door must be open to select and start cycles. Instructed customer on proper operation of machine, all checks ok."
We serviced a
LG DISHWASHER
Model LDT5678ST
Near Tacoma, WA 98408
Branden W.
Job Details:
08/11/2021
Installed new door latch. Cycle tested. All checks good.
We serviced a
MAYTAG DRYER-ELECTRIC
Model MEDB835DW4
Near Dallas, TX 75217
Jacob P.
Job Details:
08/11/2021
"Customer concern of dryer making squealing noise. Found seized idler pulley causing noise. Replaced idler pulley. Test cycled, all checks ok. ; used 1 279640 (PULLEY,IDLER) from stock"
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model WED9200SQ0
Near Puyallup, WA 98375
Branden W.
Job Details:
08/10/2021
Customer concern is that dryer does not heat. Found burnt wire and terminal at elememt causing no heat. Replaced wire and terminal. Cycle tested. Good Temps. ; used 1 279457 (WIRE-SPADE) from stock
We serviced a
GE DISHWASHER
Model GDT605PSM5SS
Near Plano, TX 75024
Jacob P.
Job Details:
08/10/2021
"Customer concern of door not latching. Found latch misaligned causing door to not close. Realigned latch. Test cycled, all checks ok."
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model WED7990FW0
Near Tacoma, WA 98403
Branden W.
Job Details:
08/10/2021
Customer concern is that dryer takes multiple cycles to dry. F4 E4 (L2 line voltage low) F3 E6 (moisture sensor open) cycle tested through different cycles and service mode. Found control board only reading 75 volts on L2. Tested at wall. 120v on L2 and L1. Tested and calibrated moisture sensors. Needs new CCU per whirlpool tech guide. Declined to repair
We serviced a
GE DISHWASHER
Model GSD3360K65SS
Near Lewisville, TX 75067
Jacob P.
Job Details:
08/10/2021
"Installed previously ordered solenoid and armature. Test cycled, all checks ok."
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM7
Near The Colony, TX 75056
Jacob P.
Job Details:
08/10/2021
"Installed previously ordered dispenser. Test cycled, all checks ok."
We serviced a
WHIRLPOOL WASHER-FRONT LOA
Model WFW9400SW02
Near Graham, WA 98338
Cameron M.
Job Details:
08/10/2021
"Customer concern is that washer produces f20 and f28 error codes ,unit has to be unplugged to reset. Found f20 (no water flow/pressure switch trip not detected) via service mode. Cleaned inlet screens of both hot and cold water valves. Cycle tested unit all checks good."
We serviced a
KENMORE WASHER-FRONT LOA
Model 11022342511
Near Coppell, TX 75019
Jacob P.
Job Details:
08/10/2021
"Installed previously ordered wash plate, agitator and dispenser cup. Test cycled, all checks ok."
We serviced a
KENMORE WASHER-TOPLOAD
Model 79631523211
Near Plano, TX 75074
Jacob P.
Job Details:
08/10/2021
"Installed previously ordered inlet valve and suspension rods. Test cycled, all checks ok."
We serviced a
KENMORE WALL OVEN
Model 79048733901
Near Dallas, TX 75248
Jacob P.
Job Details:
08/09/2021
"Performed pm check on wall oven, all checks ok."
We serviced a
LG RANGE
Model LSG4511ST 00
Near Milton, WA 98354
Branden W.
Job Details:
08/09/2021
Customer concern is that new range smells like gas. Tested all connections with electric sniffer and bubbles. Found no leaks. Advised that spent gas is normal smell when in use. Advised to always run ventilation fan from OTR microwave when using range. No issues found.
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE54M8750V/A3
Near Tacoma, WA 98407
Cameron M.
Job Details:
08/09/2021
"Installed sears supplied door seal , cycle tested unit, all checks good."
We serviced a
WHIRLPOOL WASHER-FRONT LOA
Model WFW5620HW2
Near Steilacoom, WA 98388
Cameron M.
Job Details:
08/09/2021
"Customer concern is that washer does not fill. Found loose connection at cold fill valve, cycle unit to not fill. Reseated connection, cycle tested all checks good."
We serviced a
FRIGIDAIRE DISHWASHER
Model FGHD2433KF1
Near Dallas, TX 75218
Jacob P.
Job Details:
08/09/2021
"Customer concern of unit not starting. Advised customer that door has to be open to select and start cycle. Test cycled all buttons and functions, all checks ok."
We serviced a
KENMORE DISHWASHER
Model 66516914001
Near Tacoma, WA 98408
Branden W.
Job Details:
08/09/2021
Customer concern is that dishwasher leaked. Cycle tested x2 through rinse and drain. Found no signs of leak under dishwasher. Unable to get unit to leak at this time. Advised to call if issue returns.
We serviced a
GE DISHWASHER
Model GDF610PMJ2ES
Near Graham, WA 98338
Branden W.
Job Details:
08/09/2021
Customer concern is that dishwasher does not start a cycle. Found dishwasher does not recognize door being closed causing it to not start. Found bad connection at main control causing issue. Reseated connection. Cycle tested numerous times. All checks good.
We serviced a
KENMORE DRYER-ELECTRIC
Model 11060222511
Near Garland, TX 75044
Jacob P.
Job Details:
08/09/2021
"Performed pm check on dryer, failed air flow test. Advised customer that vent from back of dryer to outside needs to be cleaned. Unit functioning as designed."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWX655DW1
Near Dallas, TX 75243
Jacob P.
Job Details:
08/09/2021
"Performed pm check on washer, all checks ok."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB835DC
Near Spanaway, WA 98387
Cameron M.
Job Details:
08/09/2021
"Customer concern is that washer does not agitate, drain and spin. Cycle tested unit empty via service mode, found no mechanical issues. Cycle tested unit 3x with customer provided load of towels. Was unable to duplicate customer concern. Advised customer to monitor ,and call if issue persists."
We serviced a
FRIGIDAIRE DISHWASHER
Model FFCD2413US1A
Near Tacoma, WA 98444
Branden W.
Job Details:
08/09/2021
Customer concern is that dishwasher does not clean or dissolve detergent. Found water to dishwasher turned off causing unit to not wash. Turned water on. Cycle tested. Unit operating as designed.
We serviced a
MAYTAG DISHWASHER
Model MDB4949SDE2
Near Puyallup, WA 98374
Branden W.
Job Details:
08/09/2021
Installed new manifold. Cycle tested. All checks good.
We serviced a
SAMSUNG WASHER-TOPLOAD
Model WA54M8750AW/A4
Near Tacoma, WA 98466
Cameron M.
Job Details:
08/06/2021
"Installed previously ordered main harness, pcb display,mems sensor. Cycle tested unit 3x all checks good."
We serviced a
GE DISHWASHER
Model GDT535PSMSS
Near Irving, TX 75062
Jacob P.
Job Details:
08/06/2021
"Installed previously ordered console face plate. Test cycled, all checks ok."
We serviced a
SAMSUNG DISHWASHER
Model DW80J9945US/AA 01
Near Sachse, TX 75048
Jacob P.
Job Details:
08/06/2021
"Installed previously ordered base, water wall motor, dispenser and toe panel. Test cycled, all checks ok."
We serviced a
FRIGIDAIRE DISHWASHER
Model FGHD2465NF1A
Near Puyallup, WA 98374
Cameron M.
Job Details:
08/06/2021
"Installed previously ordered latch asm , bord. Cycle tested unit 3x all checks good"
We serviced a
SAMSUNG DISHWASHER
Model DW80F800UWS/AA 01
Near McKinney, TX 75071
Jacob P.
Job Details:
08/06/2021
"Customer concern of LE error (leak error). Found debris between sump seal and tub causing leak. Cleaned seal and tub. Test cycled, all checks ok."
We serviced a
WHIRLPOOL DRYER-GAS
Model WGD5500ST0
Near Farmers Branch, TX 75234
Jacob P.
Job Details:
08/06/2021
"Customer concern of unit not heating. Found coil valves not opening causing no heat. Replaced coil valves, test cycled, all checks ok. ; used 1 279834 (2 COIL GAS VALVE SET) from stock"
We serviced a
FRIGIDAIRE DISHWASHER
Model LFBD2409LF3C
Near Tacoma, WA 98409
Cameron M.
Job Details:
08/05/2021
Installed previously ordered lower door gasket. Cycle tested all checks good. Left part with customer as it caused a water leak.
We serviced a
LG WASHER-FRONT LOA
Model WM2655HVA
Near Tacoma, WA 98405
Branden W.
Job Details:
08/05/2021
"Customer concern is that washer leaks. Stacked set in closet with no access. Removed set, unstained. Found leaking hot water inlet valve causing leak. Replaced valve. Cycle tested x3. Installed customer provided inlet hoses. Reinstalled. All checks ok. ; used 1 5220FR2006H (INLET VALVE (HOT)) from stock"
We serviced a
KENMORE DRYER-GAS
Model 11067072600
Near Dallas, TX 75205
Jacob P.
Job Details:
08/05/2021
"Performed pm check on dryer, all checks ok."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV45K6200EZ/A3 01
Near McKinney, TX 75070
Jacob P.
Job Details:
08/05/2021
"Customer concern of unit very noisy then stopped working. Found worn idler pulley causing no function. Replaced idler pulley. Test cycled, all checks ok. ; used 1 DC93-00634A (IDLER ASSEMBLY) from stock"
We serviced a
SAMSUNG COOKTOP
Model NZ30K7880UG/AA
Near Allen, TX 75002
Jacob P.
Job Details:
08/05/2021
"Customer concern of burning smell when using unit. Test cycled machine, no mechanical failure found. Called Samsung tech support. Per tech support, they do not recommend replacing any parts due to no mechanical failure. Reference number 7004475830"
We serviced a
SAMSUNG WASHER-FRONT LOA
Model WF42H5400AW/A2
Near Enumclaw, WA 98022
Branden W.
Job Details:
08/05/2021
Customer concern is that washer does not clean well and can smell bleach. Cycle tested. Foumd drain hose about 2 feet too far in wall drain causing hose to go past p trap. Secured hose 6 inches into drain. No mechanical issues found. Also advised to only use 2 tablespoons of detergent and run clean cycle regularly. All checks ok.
We serviced a
KENMORE DRYER-ELECTRIC
Model 11060096990
Near Frisco, TX 75035
Jacob P.
Job Details:
08/05/2021
"Installed previously ordered control panel. Test cycled, all checks ok."
We serviced a
MAYTAG WASHER-FRONT LOA
Model MHW7000XW0
Near Puyallup, WA 98374
Branden W.
Job Details:
08/05/2021
Installed new MCU. Also found inner portion of door boot where it meets drum not installed properly. Corrected door boot. Cycle tested through diagnostic and rinse and spin. All checks ok.
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB835DW0
Near Garland, TX 75043
Jacob P.
Job Details:
08/05/2021
"Installed previously ordered console. Test cycled, all checks ok."
We serviced a
KENMORE DRYER-ELECTRIC
Model 1162622101
Near Dallas, TX 75231
Jacob P.
Job Details:
08/05/2021
"Customer concern of dryer not heating. Customer advised that issue is intermittent and has worked since initial call made for service. Test cycled unit through each cycle, unit heats. Checked contacts in timer through each cycle, checks ok. Ran air flow test, yellow. Test cycled temps ?5 through each cycle, temps in range. Advised customer that vent from back of dryer needs to be cleaned. Unit is functioning as designed at time of service."
We serviced a
GE LAUNDRY CENTER
Model GUD24ESSM1WW
Near Tacoma, WA 98418
Branden W.
Job Details:
08/05/2021
Installed new inlet valve. Cycle tested. All checks good. Left failed part with customer as it caused a water leak.
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV400EWHDWR/AA
Near Puyallup, WA 98373
Cameron M.
Job Details:
08/04/2021
"Customer concern is that dryer does not tumble. Found heating element shorted to element case .also found open thermal fuse,causing unit to power but not tumble and heat. Cleaned and Vacuumed inside of dryer. Installed new element and thermal fuse. Cycle tested, all checks good. ; used 1 DC47-00016A (THERMAL FUSE), and 1 DC97-14486A (ELEMENT ASSEMBLY) from stock"
We serviced a
SAMSUNG WASHER-FRONT LOA
Model WF42H5200AP/A2 11
Near Tacoma, WA 98407
Branden W.
Job Details:
08/04/2021
Installed new door boot. Cycle tested. All checks good. Took failed part that caused a leak at customer request.
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW5000DW2
Near Richardson, TX 75080
Jacob P.
Job Details:
08/04/2021
"Installed previously ordered suspension rods. Test cycled, all checks ok."
We serviced a
GE LAUNDRY CENTER
Model GUD27GSSM2WW
Near Puyallup, WA 98372
Cameron M.
Job Details:
08/04/2021
"Customer concern is that sheet stuck under agitator. Found sheet stuck under agitator, causing unit to not agitate. Removed agitator then unwrapped sheet from main shaft, re-installed agitator. Cycle tested unit all checks good."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAHZ0
Near Frisco, TX 75035
Jacob P.
Job Details:
08/04/2021
"Installed previously ordered inlet valve. Test cycled, all checks ok."
We serviced a
KENMORE DRYER-ELECTRIC
Model 41781100002
Near Rowlett, TX 75088
Jacob P.
Job Details:
08/04/2021
"Installed previously ordered belt. Test cycled, all checks ok."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAHZ0
Near Graham, WA 98338
Branden W.
Job Details:
08/04/2021
"Customer concern is that dishwasher does not dry and upper rack is falling. Found dishwasher in heat lock out (F7 E1) reset through diagnostic cycle. Cycle tested. Good water level, spray pressure and heat. Unable to find any issue. Replaced broken upper rack adjuster kit. All checks good. ; used 1 W10712395 (ADJUSTER) from stock"
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE52M8650V/A3
Near Puyallup, WA 98375
Branden W.
Job Details:
08/04/2021
Installed new user board. Found dryer duct came off at blower housing. Likely cause of moisture buildup. Secured duct with metal heat tape to blower housing. Cycle tested. All checks good.
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model WED9600TA0
Near Spanaway, WA 98387
Branden W.
Job Details:
08/04/2021
Installed new main control. Cycle tested. All checks good.
We serviced a
MAYTAG DRYER-ELECTRIC
Model MEDC465HWO
Near Spanaway, WA 98387
Cameron M.
Job Details:
08/04/2021
Customer concern is that dryer takes multiple cycles to dry clothes. Preformed airflow test failed (red). Cleaned and calibrated moisture sensors. Advised customer dryer vent needs to be shortened. Also advised customer dryer duct needs to be cleaned asap
We serviced a
MAGIC CHEF RANGE
Model CES3540AAC
Near Puyallup, WA 98375
Branden W.
Job Details:
08/03/2021
"Customer concern is that range does not heat. Found all elements, cooktop and oven do not produce heat. Found only 120vac supplied to range causing no heat. Found loose wall plug causing poor connection with power cord. Was able to get 240vac to range. Tested all elements. All check good. Advised that an electrician is needed to replace wall plug. Range is sitting on board runners and not feet of range. Did not remove range. Accessed power plug from under range."
We serviced a
KENMORE DRYER-GAS
Model 11065132411
Near Coppell, TX 75019
Jacob P.
Job Details:
08/03/2021
"Customer concern of long dry times and not much lint in trap. Ran air flow test, 100% plugged. Removed vent and ran air flow test again, passed. Advised customer that vent from back of dryer to outside needs to be cleaned asap. Unit functioning as designed."
We serviced a
GE DISHWASHER
Model GDF450PSR0SS
Near Lewisville, TX 75067
Jacob P.
Job Details:
08/03/2021
"Customer concern of door not latching. Found unit installed improperly causing door not to latch. Reinstalled unit. Test cycled, all checks ok."
We serviced a
LG DRYER-ELECTRIC
Model DLEX3570V
Near Puyallup, WA 98375
Branden W.
Job Details:
08/03/2021
Installed new main control. Cycle tested. All checks good.
We serviced a
KITCHENAID DISHWASHER
Model KDTM354DSS4
Near Bonney Lake, WA 98391
Branden W.
Job Details:
08/03/2021
"Installed new sump assembly, spray arms and turbidity sensor. Cycle tested x3. All checks good."
We serviced a
GE DISHWASHER
Model GDF570SSJ0SS
Near Buckley, WA 98321
Branden W.
Job Details:
08/03/2021
Installed new control board. Cycle tested. All checks good.
We serviced a
KENMORE COOKTOP
Model 79032683411
Near Dallas, TX 75211
Jacob P.
Job Details:
08/03/2021
"Installed previously ordered valves, burner bodies and orifice holders. Test cycled, all checks ok."
We serviced a
SAMSUNG RANGE
Model NE58K9430SS/AA
Near Tacoma, WA 98446
Branden W.
Job Details:
08/03/2021
Installed new infinite switches. Cycle tested. All checks ok.
We serviced a
KENMORE WASHER-FRONT LOA
Model 79640512900
Near Tacoma, WA 98498
Cameron M.
Job Details:
08/03/2021
"Customer concern is that washer does not drain strted producing oe error intermittently a week ago, now leaves water in unit. Found failed drain pump, causing unit to not drain. Needs new drain pump. Installed new drain pump, cycle tested unit 3x. All checks good ; used 1 4681EA2001T (DRAIN PUMP) from stock"
We serviced a
HOTPOINT DRYER-ELECTRIC
Model HTDX100EM8WW
Near Lakewood, WA 98498
Cameron M.
Job Details:
08/03/2021
"Customer concern is that dryer does not heat, takes hours to dry clothes. Preformed airflow test, failed (red).found shorted contact on lower right connector of element, causing unit to not heat during operation. Needs new terminal connector. Installed new thermal spade, cycle tested unit all check good.Advised customer dryer duct needs to be cleaned asap before dryer use resumes. ; used 1 279457 (WIRE-SPADE) from stock"
We serviced a
KENMORE DRYER-ELECTRIC
Model 110.696228
Near Spanaway, WA 98387
Cameron M.
Job Details:
08/02/2021
"Customer concern is that dryer does not heat. Preformed airflow test failed (yellow).found open heating element, causing unit to not heat. Needs new heating element. Installed new heating element. Cycle tested all checks good. ; used 1 279838 (ELEMENT,HEATER) from stock"
We serviced a
SAMSUNG WASHER-FRONT LOA
Model WF448AAP/XAA
Near Spanaway, WA 98387
Cameron M.
Job Details:
08/02/2021
"Customer requested maintenance and service . Cleaned out drain pump .cycle tested unit. Found a slight leak from door boot , Advised customer on keeping sealing surface clean to prevent future leaks."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB725BW0
Near Tacoma, WA 98406
Branden W.
Job Details:
08/02/2021
"Installed new bearing kit, rotor, stator and hub. Cycle tested. All checks good."
We serviced a
SAMSUNG WASHER-FRONT LOA
Model WV55M9600AV/A5 02
Near Lakewood, WA 98498
Cameron M.
Job Details:
08/02/2021
"Installed previously ordered display assembly. Cycle tested, all checks good."
We serviced a
JENN-AIR COOKTOP
Model C221
Near Fairview, TX 75069
Jacob P.
Job Details:
08/02/2021
"Installed previously ordered infinite switch. Test cycled, all checks ok."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB835DW4
Near Sumner, WA 98391
Branden W.
Job Details:
08/02/2021
Installed new washplate. Removed a lot of coins from under plate. Advised to check pockets to prevent coins in washer. All checks ok.
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model WED4815EW1
Near Dallas, TX 75220
Jacob P.
Job Details:
08/02/2021
"Installed previously ordered timer. Test cycled, all checks ok."
We serviced a
GE DRYER-ELECTRIC
Model GTX22EASK0WW
Near Irving, TX 75063
Jacob P.
Job Details:
08/02/2021
"Customer concern of unit making loud noise. Test cycled, unit functioning fine. Ran air flow test, failed. Advised customer that dryer duct to outside needs to be cleaned. Unit functioning as designed."
We serviced a
GE DISHWASHER
Model GDF535PSR0SS
Near Irving, TX 75063
Jacob P.
Job Details:
08/02/2021
"Customer concern of unit not draining. Found garbage disposal plug still in causing no drain. Removed plug. Test cycled, all checks ok."
We serviced a
FRIGIDAIRE DISHWASHER
Model FFBD2406NS9B
Near Puyallup, WA 98373
Branden W.
Job Details:
08/02/2021
Customer concern is that dishwasher does not dry. Cycle tested dishwasher. Found no mechanical issues. Advised to change rinse aid setting higher. And make sure 120 degree water is supplied to dishwasher.
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV42H5200EP/A3 02
Near Puyallup, WA 98374
Branden W.
Job Details:
08/02/2021
"Customer concern is that dryer was making noise and now does not start a cycle. Found failed idler pulley caused belt to come off. Also found worn roller. Replaced idler pulley and roller. Cleaned and lubed other rollers. Cycle tested. All checks good. ; used 1 DC93-00634A (IDLER ASSEMBLY), and 1 DC97-16782A (DRUM ROLLER) from stock"
We serviced a
FRIGIDAIRE DISHWASHER
Model FGHD2433KF1
Near Dallas, TX 75218
Jacob P.
Job Details:
08/02/2021
"Installed previously ordered control board. Test cycled, all checks ok."
We serviced a
MAYTAG DRYER-ELECTRIC
Model MEDB765FC0
Near Buckley, WA 98321
Cameron M.
Job Details:
08/02/2021
"Customer concern is that dryer does not work. Found plunger on door switch broke off, causing unit to not start cycle as it does not recognize door is closed. Needs new door switch. Installed new door switch, cycle tested unit. All checks good. ; used 1 WP3406107 (SWITCH-DOR) from stock"
We serviced a
SAMSUNG DISHWASHER
Model DW80M9550UG/AA
Near Spanaway, WA 98387
Branden W.
Job Details:
07/30/2021
Customer concern is that dishwasher produced LE (leak detected) error. Turned breaker on. Cycled. No leak. Removed dishwasher to access lower leak pan. No water present in pan. Found no signs of leak from Any components. Reinstalled. Cycle tested x3 in rinse cycle. No leaks or errors present at this time. Advised to call if issue returns. Toe panel not present prior to service.
We serviced a
GE DISHWASHER
Model GDT630PYM6FS
Near Wylie, TX 75098
Jacob P.
Job Details:
07/30/2021
"Customer concern of unit not starting. Customer advised that she adjusted the dishwasher and was able to get it to start working again. Test cycled all components, unit functioning as designed. All checks ok."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB865GC0
Near Sachse, TX 75048
Jacob P.
Job Details:
07/30/2021
"Customer concern of sheet stuck under agitator. Removed sheet from agitator. Checked wash plate for warping, all checks ok."
We serviced a
SAMSUNG WASHER-TOPLOAD
Model WA50R5400AV/US 02
Near Orting, WA 98360
Branden W.
Job Details:
07/30/2021
Customer concern is that washer did not spin out water once when washing a blanket. Cycle tested with a load of towels. Unit operating as designed. Advised about out of balance loads. Advised to add a few towels in when washing single blanket.
We serviced a
GE WASHER-TOPLOAD
Model WHDSR109J5WW
Near Enumclaw, WA 98022
Branden W.
Job Details:
07/30/2021
"Customer concern is that washer leaks when set to super water level and when set to small it does not spin out. Found pressure hose full of gunk causing washer to overfill and leak. Replaced pressure hose. Cycle tested with towels. Unit spinning properly at this time. Left old pressure hose with customer as it caused a water leak. ; used 1 WH41X365 (HOSE,WATER LEVEL) from stock"
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model WED8500DC3
Near University Place, WA 98467
Cameron M.
Job Details:
07/30/2021
"Installed previously ordered main control, cycle tested unit. All checks good"
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWC415EW0
Near Bonney Lake, WA 98391
Branden W.
Job Details:
07/30/2021
Customer concern is that washer does not fill with enough water and she has to use garden hose to fill washer. Found washer operating as designed. Advised to use deep water wash cycle.
We serviced a
KENMORE WASHER-TOPLOAD
Model n/a
Near Eatonville, WA 98328
Branden W.
Job Details:
07/30/2021
Model/serial tag missing. Customer concern is that washer leaks a lot of water from bottom. Found hole in drain pump causing leak. Replaced pump. Left failed part as it caused a leak. All checks ok. ; used 1 WP3363394 (PUMP-WATER) from stock
We serviced a
WHIRLPOOL RANGE
Model WFE520C0AS 0
Near Irving, TX 75061
Jacob P.
Job Details:
07/30/2021
"Customer concern of front right burner always on high. Found shorted infinite switch causing incorrect temperatures. Replaced infinite switch. Test cycled, all checks ok. Left unit uninstalled per customer's request. ; used 1 WP3149400 (SWITCH-INF) from stock"
We serviced a
KENMORE WASHER-TOPLOAD
Model 11022352510
Near Mesquite, TX 75150
Jacob P.
Job Details:
07/30/2021
"Performed pm check on washer, all checks ok."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV45H7000EW/A2 02
Near Tacoma, WA 98499
Cameron M.
Job Details:
07/29/2021
"Installed previously ordered drive motor. Cleaned and Vacuumed inside of unit. Cycle tested unit 3x, all checks good."
We serviced a
KITCHENAID DISHWASHER
Model KDFE104DSS2
Near Dallas, TX 75248
Jacob P.
Job Details:
07/29/2021
"Installed previously ordered control board and thermistor. Test cycled, all checks ok."
We serviced a
FRIGIDAIRE DISHWASHER
Model FBD2400KW10B
Near Frisco, TX 75034
Jacob P.
Job Details:
07/29/2021
"Customer concern of unit filling with water while off. Found no high loop installed causing sink to back flow into dishwasher. Installed drain hose and high loop. Test cycled, all checks ok. ; used 1 8269144A (DRAIN HOSE), and 1 43259 (HOSE CLAMP 9/16 X 1 1/4) from stock"
We serviced a
SAMSUNG WASHER-FRONT LOA
Model WF42H5200AW/A2 01
Near McKinney, TX 75070
Jacob P.
Job Details:
07/29/2021
"Installed previously ordered inverter board and rps sensor. Test cycled, all checks ok."
We serviced a
SAMSUNG WASHER-FRONT LOA
Model WF42H5200AP/A2 11
Near Tacoma, WA 98404
Branden W.
Job Details:
07/29/2021
Customer concern is that washer walks in spin cycle. Cycle tested empty and with a load. Found front left leveling foot too high causing washer to shake. Leveled washer. All checks good.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAHZ0
Near Puyallup, WA 98372
Branden W.
Job Details:
07/29/2021
Installed new door seal. Cycle tested. All checks good.
We serviced a
AMANA DISHWASHER
Model ADB1100AWS
Near Edgewood, WA 98372
Branden W.
Job Details:
07/29/2021
Customer concern is that dishwasher does not run a cycle. Found water supply turned off under sink causing dishwasher to not run a cycle. Turned water on. Cycle tested x3. All checks good.
We serviced a
KITCHENAID DISHWASHER
Model KUDC10IXWH0
Near Fircrest, WA 98466
Cameron M.
Job Details:
07/29/2021
"Installed previously ordered user interface and control board. Cycle tested unit,all checks good."
We serviced a
SAMSUNG WASHER-FRONT LOA
Model WF42H5200AW/A2 11
Near Spanaway, WA 98387
Branden W.
Job Details:
07/29/2021
Customer concern is that washer will not run a cycle. Found washer never activates drum motor. Found 3E2 error stored. Motor ohms at 10.5 on all legs. Needs new inverter board and hall sensor. Declined to repair at this time.
We serviced a
KENMORE WASHER-FRONT LOA
Model 41741142000
Near Eatonville, WA 98328
Branden W.
Job Details:
07/29/2021
"Customer concern is that washer has been loud then started banging and walking. Found right tub spring broke causing tub to fall. Also found failed tub bearings. Needs new rear tub, basket,springs, shocks, door boot and belt. Declined to repair at this time"
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB725BW0
Near Rowlett, TX 75088
Jacob P.
Job Details:
07/28/2021
"Installed previously ordered lid lock. Test cycled, all checks ok."
We serviced a
WHIRLPOOL DISHWASHER
Model WDF560SAFM1
Near Dallas, TX 75214
Jacob P.
Job Details:
07/28/2021
"Installed previously ordered wash pump and grommet. Test cycled, all checks ok."
We serviced a
GE RANGE
Model JBP27WL1WW
Near Puyallup, WA 98374
Branden W.
Job Details:
07/28/2021
Customer concern is that range loses power. Comes back on when range is slid out. Found loose wall plug causing bad connection with power cord. Found no issues with range. Needs new wall plug. Advised an electrician is needed. NO CHARGE.
We serviced a
KENMORE WASHER-FRONT LOA
Model 79641473210
Near Dallas, TX 75214
Jacob P.
Job Details:
07/28/2021
"Installed previously ordered door boot and spring. Test cycled, all checks ok. Left failed part with customer."