Service History 133 - RPS Appliance Repair

We serviced a

GE RANGE

Model JBP66SM2SS

Near Fife, WA 98424

Branden W.

Job Details: 07/16/2021

Installed new infinite switch. Cycle tested. All checks good.

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV50K7500EV/A3 01

Near Bonney Lake, WA 98391

Cameron M.

Job Details: 07/16/2021

"Installed previously ordered element, Cleaned and Vacuumed inside of unit , cycle tested all checks good."

We serviced a

SAMSUNG WASHER-FRONT LOA

Model WF45R6100AC/US

Near Tacoma, WA 98445

Branden W.

Job Details: 07/16/2021

Customer concern is that washer does not unlock. Found washer stopped and full of water causing door to remain locked. Ran drain cycle. Door unlocked. Retrieved errors stored. Only error was UB (unbalanced load) cycle tested in normal cycle. Found no issues at time of service. Advised about out of balance loads. Also found drain hose too far in wall drain creating a siphon. Secured drain hose at proper depth.

We serviced a

WHIRLPOOL WASHER-TOPLOAD

Model LXR5432KQ10

Near University Place, WA 98467

Branden W.

Job Details: 07/16/2021

Customer concern is that washer overflowed and leaked. Found sock lodged in drain pump causing washer to not drain and overflow. Removed sock. Cycle tested x3 with a load on both water levels. All checks good.

We serviced a

MAYTAG WASHER-FRONT LOA

Model MHW5630HW0

Near Dallas, TX 75206

Jacob P.

Job Details: 07/16/2021

"Customer concern of display not responding. Found loose ribbon cable on hmi causing no function. Reseated ribbon cable. Test cycled, all checks ok."

We serviced a

WHIRLPOOL DISHWASHER

Model WDF520PADM5

Near Tacoma, WA 98404

Branden W.

Job Details: 07/15/2021

"Customer concern is that after plumber reinstalled dishwasher, it does not operate. Cycle tested x4. Unable to duplicate concern at this time. Advised to call if issue returns."

We serviced a

WHIRLPOOL WASHER-FRONT LOA

Model WFW9400SZ02

Near Spanaway, WA 98387

Cameron M.

Job Details: 07/15/2021

"Installed previously ordered door hinge, cycle tested all checks good."

We serviced a

SAMSUNG WASHER-TOPLOAD

Model WA400PJHDWR/AA

Near Dallas, TX 75206

Jacob P.

Job Details: 07/15/2021

"Installed previously ordered drain pump kit. Test cycled, all checks ok."

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWB835DW4

Near Spanaway, WA 98387

Branden W.

Job Details: 07/14/2021

Customer concern is that washer makes noise in agitation cycle. Cycle tested with a load. Found suspension rods squeaking. Cleaned suspension rod saddles. Cycle tested. All checks good.

We serviced a

SAMSUNG WASHER-FRONT LOA

Model WF56H9100AW/A2 01

Near Spanaway, WA 98387

Branden W.

Job Details: 07/14/2021

Customer concern is that washer leaks from door. Found door boot not seated properly on bottom left causing leak. Reseated door boot. All checks ok.

We serviced a

FRIGIDAIRE RANGE

Model GLGFZ386FCD

Near Spanaway, WA 98387

Cameron M.

Job Details: 07/14/2021

"Customer concern is that range bakes does not ignite and front left burner flame is inconsistent. Found bake ignitor drawings 2.32 of the 3.3 amp requirement for igniting properly. Needs new ignitor. Installed new ignitor, cycle tested 3x. All checks good. ; used 1 WB13K21 (OVEN IGNITER-12' LEAD W/NUTS) from stock"

We serviced a

GE WASHER-FRONT LOA

Model GFW450SSM1WW

Near Tacoma, WA 98408

Cameron M.

Job Details: 07/14/2021

"Customer concern is that washer makes noise during spin cycle. Cycle tested unit 3x empty without unit making noise. Cycle tested unit with customer provided load of two blankets and a towel, found air chamber loose, also found top counter weight fasteners. Tightened air chamber fasteners and counter weight fasteners. Cycle tested all checks good."

We serviced a

SAMSUNG OVEN/STOVE

Model NX58H9500WS/AA

Near Fairview, TX 75069

Jacob P.

Job Details: 07/14/2021

"Customer concern that unit won't go above 285. Found unit set to Celsius. Changed program to Fahrenheit. Test cycled, all checks ok."

We serviced a

WHIRLPOOL WASHER-FRONT LOA

Model WTW8500DC5

Near Puyallup, WA 98375

Cameron M.

Job Details: 07/14/2021

Installed previously ordered lid. Cycle tested all checks good.

We serviced a

WHIRLPOOL WASHER-FRONT LOA

Model WTW8500DC2

Near Puyallup, WA 98374

Cameron M.

Job Details: 07/14/2021

"Customer concern is that washer does not fill with cold water and produces LF error. found Unit produces f8e1 (long fill). Also found cold inlet valve stuck closed, causing unit to not fill with cold water and producesLF error. Needs new inlet valve assembly. Installed new inlet valve assembly cycle tested all checks good. ; used 1 W11165546 (VALVE) from stock"

We serviced a

GE DRYER-ELECTRIC

Model GTD84ECSN1WS

Near McKinney, TX 75071

Jacob P.

Job Details: 07/14/2021

"Installed previously ordered wire harness. Test cycled, all checks ok."

We serviced a

WHIRLPOOL WASHER-FRONT LOA

Model WFW5620HW

Near Tacoma, WA 98444

Branden W.

Job Details: 07/14/2021

Customer concern is that washer produces LO FLO or F8 E1 (long fill) error. Cycle tested numerous times in different cycles. All 3 inlet valves operating and have good pressure. Unable to get unit to fail at this time. Advised to call if issue returns.

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWB700VQ0

Near Tacoma, WA 98408

Branden W.

Job Details: 07/14/2021

Installed new bearing and hub. Cycle tested. All checks good.

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV50K8600EV/A3 01

Near Frisco, TX 75035

Jacob P.

Job Details: 07/14/2021

"Customer concern of unit making loud noise and duct cleaning company said dryer wasn't blowing air. Found worn idler pulley causing noise. Replaced idler pulley. Ran air flow test, passed. All checks ok. ; used 1 DC93-00634A (IDLER ASSEMBLY) from stock"

We serviced a

KENMORE WASHER-TOPLOAD

Model 11082984800

Near Carrollton, TX 75006

Jacob P.

Job Details: 07/14/2021

"Installed previously ordered inlet valve. Test cycled, all checks ok."

We serviced a

SAMSUNG WASHER-FRONT LOA

Model WF42H5000AW/A2 11

Near Tacoma, WA 98409

Branden W.

Job Details: 07/14/2021

Customer concern is that washer is banging and shaking in spin cycle. Cycle tested empty and with a load. No mechanical issues found with washer. Secured loose hose that came out of holder. All checks good.

We serviced a

WHIRLPOOL RANGE

Model WEG750H0HZ0

Near Bonney Lake, WA 98391

Branden W.

Job Details: 07/14/2021

Customer concern is that bake does not operate. Found bake and DBL relays on ACU board not closing causing no bake to not operate. Needs new ACU board. Declined tomrepair at this time.

We serviced a

MAYTAG WASHER-FRONT LOA

Model MHW5100DC0

Near Spanaway, WA 98387

Cameron M.

Job Details: 07/13/2021

"Customer concern is that washer door does not close properly. Found washer door misaligned, causing door to not close properly. Adjusted door cycle tested all checks good."

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DVE50R5200W/A3

Near Puyallup, WA 98375

Cameron M.

Job Details: 07/13/2021

"Customer concern is that dryer is making a squeaking noise during operation and takes multiple cyclesto dry clothes. Preformed airflow test (yellow).found seized idler pulley ,causing unit to make noise during operation. Also found clogged lint screen mesh causing a restriction of airflow. Needs new idler pulley. Installed new idler pulley and cleaned and vacuumed inside of dryer. Also cleaned and calibrated moisture sensors. Advised customer dryer duct needs to be cleaned asap. ; used 1 DC93-00634A (IDLER ASSEMBLY) from stock"

We serviced a

KENMORE WASHER-FRONT LOA

Model 11029822801

Near Tacoma, WA 98444

Branden W.

Job Details: 07/13/2021

Customer concern is that a fill hose has a hole in it. Found hole in fill hose causing leak. Replaced fill hoses. Left old hoses with customer as they caused a leak. Reset leveling legs. ; used 1 3805FFSS-2 (FILL HOSE 2 PACK 5' SS) from stock

We serviced a

GE DISHWASHER

Model GDT550HSD4SS

Near Puyallup, WA 98374

Branden W.

Job Details: 07/13/2021

Installed new wash pump kit. Cycle tested. All checks good.

We serviced a

WHIRLPOOL RANGE

Model WFE525S0HB0

Near Garland, TX 75043

Jacob P.

Job Details: 07/13/2021

Customer concern of no elements in oven heat. Found burnt power cord to unit causing only 120v supply. Advised customer that power cord is not covered under warranty. Removed power cord and gave to customer.

We serviced a

KENMORE WASHER-TOPLOAD

Model 11026132410

Near Dallas, TX 75206

Jacob P.

Job Details: 07/13/2021

"Installed previously ordered suspension rods. Test cycled, all checks ok."

We serviced a

KITCHENAID RANGE

Model KGRS505XSS03

Near Dallas, TX 75206

Jacob P.

Job Details: 07/13/2021

"Installed previously ordered igniter. Test cycled, unit now lights. Customer concern of upper oven taking too long to cook. Temp probe ohms in range. Test cycled temps, checks ok. Advised customer unit is functioning as designed."

We serviced a

GE DRYER-ELECTRIC

Model GTD33EASK0WW

Near Buckley, WA 98321

Branden W.

Job Details: 07/13/2021

Customer concern is that dryer shuts off as soon as it is started. Found broken drum belt causing unit to not run. Replaced belt. Cycle tested. All checks good. ; used 1 WE12M29 (BELT DRIVE) from stock

We serviced a

FRIGIDAIRE DISHWASHER

Model FGID2477RF6A

Near Frisco, TX 75034

Jacob P.

Job Details: 07/13/2021

"Customer concern of unit not level. Leveled machine. Test cycled, all checks ok."

We serviced a

KITCHENAID DISHWASHER

Model KUDE70FXSS1

Near The Colony, TX 75056

Jacob P.

Job Details: 07/13/2021

"Customer concern of unit not turning on and door not closing. Found front left leveling leg fallen behind tile in cavity causing door to not close. Moved machine and releveled. Advised customer that there are no mounting brackets or screws so failure might happen again. Found power into control board loose causing no power. Reseated connector. Test cycled, all checks ok."

We serviced a

FRIGIDAIRE WALL OVEN

Model FEB30T7FCC

Near Puyallup, WA 98372

Branden W.

Job Details: 07/13/2021

Customer concern is that oven door falls open. Found both upper and lower door hinges failed causing doors to not close properly. Needs new hinges 318024714 part is discontinued. No stock available.

We serviced a

SAMSUNG WASHER-TOPLOAD

Model WA422PRHDWR/AA 01

Near Spanaway, WA 98387

Branden W.

Job Details: 07/13/2021

"Customer concern is that washer will not start a cycle and lock light is on. Errors stored are D5 (door switch), 9E (clutch failure). Found washer intermittently fails to see motor RPM causing lid to not unlock and unit to not start a cycle. Connections are seated properly. Per Samsung STG. Need to replace main PCB and hall sensor. Also found clutch motor failing to fully engage to spin causing 9E error. Needs new clutch motor. Declined to repair at this time."

We serviced a

KENMORE WASHER-TOPLOAD

Model 11028902790

Near Garland, TX 75040

Jacob P.

Job Details: 07/13/2021

"Customer concern of unit not draining or spinning. Found lid switch housing separated causing no spin. Reconnected lid switch housing. Test cycled, all checks ok."

We serviced a

WHIRLPOOL WASHER-TOPLOAD

Model WTW5000DW3

Near Bonney Lake, WA 98391

Cameron M.

Job Details: 07/12/2021

"Customer concern is that washer does not fill with water completely, unit only fills with 4 inches of water.cycle tested unit 3x empty, also cycle tested 5x with customer provided load. Was unable to duplicate customer concern, Advised customer to call if issue persists."

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV45K6200EW/A3 02

Near Dallas, TX 75208

Jacob P.

Job Details: 07/12/2021

"Customer concern of unit producing HC error. Customer had dryer duct uninstalled upon arrival. Ran temp test, in range. Ran air flow test, passed. Installed duct. Test cycled temps, in range. Ran air flow test, passed. Unable to verify complaint. Unit functioning as designed."

We serviced a

MAYTAG DISHWASHER

Model MDB7759AWS2

Near Fife, WA 98424

Branden W.

Job Details: 07/12/2021

Customer concern is that dishwasher does not operate and lights flash. Found poor connection from TouchPad at main control. Reseated connection at board. Cycle tested on all cycles. All checks good.

We serviced a

WHIRLPOOL WASHER-TOPLOAD

Model WTW7300DW0

Near Frisco, TX 75034

Jacob P.

Job Details: 07/12/2021

"Installed previously ordered control board, rotor and slider. Test cycled, all checks ok."

We serviced a

WHIRLPOOL WASHER-TOPLOAD

Model WTW7300DW0

Near McKinney, TX 75070

Jacob P.

Job Details: 07/12/2021

"Installed previously ordered suspension rods. Test cycled, all checks ok."

We serviced a

GE WALL OVEN

Model JT3800SH7SS

Near Rockwall, TX 75032

Jacob P.

Job Details: 07/12/2021

"Installed previously ordered wire harnesses, unit still producing error code. Called ge tech support, GE to replace unit. Advised customer they will need to call into GE with case number. Case number: 05971479"

We serviced a

KENMORE WASHER-TOPLOAD

Model 11025132411

Near Garland, TX 75040

Jacob P.

Job Details: 07/12/2021

"Performed pm check on washer, all checks ok."

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV45K6500EV/A3 01

Near Spanaway, WA 98387

Cameron M.

Job Details: 07/12/2021

"Customer concern is that dryer makes squealing noise during operation. Preformed airflow test failed (red). Found seized idler pulley, causing unit to make squealing noise during operation. Needs new idler pulley. Installed new idler pulley,cycle tested unit. All checks good. Advised customer dryer duct needs to be cleaned asap, prior to continuous use.; used 1 DC93-00634A (IDLER ASSEMBLY) from stock"

We serviced a

SAMSUNG WASHER-FRONT LOA

Model WF42H5200AF/A2 11

Near Puyallup, WA 98375

Branden W.

Job Details: 07/09/2021

Customer concern is that washer does not finish cycle. Found washer power cycles continuously every 10 seconds or so. 120v to main control. Main relay on main control loses power. Needs new main control. Advised there may be further issues. Declined to repair at this time

We serviced a

WHIRLPOOL COOKTOP

Model WCG51US0DS00

Near McKinney, TX 75071

Jacob P.

Job Details: 07/09/2021

"Installed previously ordered igniter harness. Test cycled, all checks ok. Unit was sealed in with silicone. Advised customer that we had to cut silicone to repair and we will not be able to reseal it."

We serviced a

ELECTROLUX DRYER-ELECTRIC

Model EIMED55IMB0

Near Tacoma, WA 98499

Cameron M.

Job Details: 07/09/2021

"Customer concern is that dryer does not heat. Found no mechanical issues at time of service. Did find unit is not getting the required 240v supply, the unit is only getting 120v. Causing unit to run but not heat. Advised customer eltrition is need to resolve the issue issue"

We serviced a

FRIGIDAIRE DISHWASHER

Model FDB1100RHM0

Near Dallas, TX 75206

Jacob P.

Job Details: 07/09/2021

"Installed previously ordered wash pump and drain pump. Test cycled, all checks ok."

We serviced a

GE WASHER-FRONT LOA

Model WBVH5200J3WW

Near Lake Tapps, WA 98391

Branden W.

Job Details: 07/09/2021

Customer concern is that washer does not advance or finish cycle. Cycle tested washer. Unit started leaking from drain pump filter. Found filter not installed causing leak. Installed filter. Found drain pump does not operate. Has 120v to pump. Needs new drain pump. Unable to fully test washer for further problems. Customer will call if they decide to repair

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV42H5600EP/A3 01

Near Dallas, TX 75204

Jacob P.

Job Details: 07/09/2021

"Customer concern of unit making loud noise. Found seized idler pulley causing noise. Replaced idler pulley, cleaned and lubed rollers. Test cycled, all checks ok. ; used 1 DC93-00634A (IDLER ASSEMBLY) from stock"

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWX655DW0

Near Dallas, TX 75238

Jacob P.

Job Details: 07/09/2021

"Installed previously ordered wash plate. Test cycled, all checks ok."

We serviced a

SAMSUNG DISHWASHER

Model DW80R5061US/AA 00

Near Bonney Lake, WA 98391

Branden W.

Job Details: 07/08/2021

"Installed new case brake, drain hose, inlet valve, main pba and drain pump as requested by tech support. Cycle tested. All checks good at this time."

We serviced a

KITCHENAID OVEN-WALL

Model KEBS207SSS04

Near Puyallup, WA 98371

Branden W.

Job Details: 07/08/2021

Installed new relay board. Calibrated both ovens at 350. Tested to 450. All checks good.

We serviced a

WHIRLPOOL WASHER-TOPLOAD

Model WTW7040DW1

Near Tacoma, WA 98444

Cameron M.

Job Details: 07/08/2021

"Customer concern is that washer intermittently does not spin and makes noise during spin cycle. Was unable to reproduce customer concern, Advised customer to monitor unit and call back if issue persists."

We serviced a

WHIRLPOOL DISHWASHER

Model DU1055XTSB3

Near DuPont, WA 98327

Cameron M.

Job Details: 07/08/2021

"Installed previously ordered drain pump,drain hoses,and control panel. Cycle tested unit 10x all checks good."

We serviced a

GE DISHWASHER

Model GDF535PSR0SS

Near Wylie, TX 75098

Jacob P.

Job Details: 07/08/2021

"Came to install spray arm, customer not home. Called customer, advised its ok to leave part and he will install it himself. Left part on front porch."

We serviced a

FRIGIDAIRE DISHWASHER

Model FFBD2408NS2A

Near Graham, WA 98338

Branden W.

Job Details: 07/08/2021

Customer concern is that dishwasher is stuck in child lock and leaks at inlet valve. Removed child lock and tested all buttons for communication. No issues found. Also found fill hose cross threaded on fill valve causing leak. Reinstalled hose to valve properly. Cycle tested dishwasher. All checks good.

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model LEW0050PQ3

Near Dallas, TX 75248

Jacob P.

Job Details: 07/08/2021

"Customer concern of unit not turning on. Found broken door switch wire causing unit to think door is open. Repaired wire. Test cycled, all checks ok."

We serviced a

WHIRLPOOL WASHER-TOPLOAD

Model WTW4850XQ0

Near Mesquite, TX 75150

Jacob P.

Job Details: 07/08/2021

"Installed previously ordered suspension rods. Test cycled, all checks ok."

We serviced a

GE RANGE

Model PGP7036SL1SS

Near Rockwall, TX 75087

Jacob P.

Job Details: 07/08/2021

"Customer concern of burners going out when on low. Adjusted valves open. Test cycled, all checks ok."

We serviced a

MAYTAG DRYER-GAS

Model MGDC300BW0

Near Puyallup, WA 98375

Branden W.

Job Details: 07/07/2021

Customer concern is that dryer does not heat. Found failed gas valve coils causing unit to not light off. Replaced gas valve coils. Cycle tested. All checks good. ; used 1 279834 (2 COIL GAS VALVE SET) from stock

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DVE52M8650V/A3

Near Puyallup, WA 98375

Branden W.

Job Details: 07/07/2021

Installed new display board. Cycle tested. All checks good.

We serviced a

SAMSUNG DISHWASHER

Model DW80M2020US/AA 00

Near Graham, WA 98338

Cameron M.

Job Details: 07/07/2021

"Installed previously ordered inlet valve, cycle tested all checks good. Customer declined to keep defective part."

We serviced a

KENMORE DRYER-ELECTRIC

Model 11062342511

Near Allen, TX 75002

Jacob P.

Job Details: 07/07/2021

"Customer concern of dryer not starting. Found open thermal fuse causing no start. Replaced thermal fuse. No heat in air fluff and air flow test pass. Test cycled, all checks ok. ; used 1 WP3392519 (FUSE-THRML) from stock"

We serviced a

MAYTAG WASHER-FRONT LOA

Model MHWE950WW01

Near Bonney Lake, WA 98391

Branden W.

Job Details: 07/07/2021

Installed new door boot. Cycle tested. All checks good. Left failed part as it caused a water leak.

We serviced a

KENMORE WASHER-TOPLOAD

Model 11022342511

Near Allen, TX 75002

Jacob P.

Job Details: 07/07/2021

"Performed pm check on washer, all checks ok."

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DV40J3000EW/A2 02

Near Tacoma, WA 98444

Cameron M.

Job Details: 07/07/2021

Customer concern is that dryer makes clicking noise during operation. Found no mechanical issues present. Advised customer to call if issue persists.

We serviced a

MAYTAG DRYER-ELECTRIC

Model MEDC300BW0

Near McKinney, TX 75070

Jacob P.

Job Details: 07/07/2021

"Customer concern of unit not turning on. Found open thermal fuse causing no power. Replaced thermal fuse. No heat in air fluff, air flow test pass. Test cycled, all checks ok. ; used 1 WP3392519 (FUSE-THRML) from stock"

We serviced a

FRIGIDAIRE DISHWASHER

Model FBD2400KW10B

Near Frisco, TX 75034

Jacob P.

Job Details: 07/07/2021

"Installed previously ordered inlet valve, door seal, drain hose and racks. Test cycled, all checks ok. Left water supply off to unit per customers request."

We serviced a

LG WASHER-TOPLOAD

Model WT7200CW

Near Enumclaw, WA 98022

Branden W.

Job Details: 07/07/2021

Customer concern is that washer will not agitate and did not drain. Found debris lodged between washplate and basket causing no agitation. Removed debris. Cycle tested empty and with a load. Washer operating properly.

We serviced a

KITCHENAID RANGE

Model KSEG950ESS1

Near Sumner, WA 98391

Cameron M.

Job Details: 07/07/2021

"Installed previously ordered infinite switch, cycle tested all checks good."

We serviced a

SAMSUNG WASHER-FRONT LOA

Model WF45K6500AV/A2 11

Near Puyallup, WA 98374

Cameron M.

Job Details: 07/06/2021

"Installed previously ordered knob assembly, cycle tested all checks good."

We serviced a

KENMORE DRYER-ELECTRIC

Model 11068732700

Near Dallas, TX 75228

Jacob P.

Job Details: 07/06/2021

"Customer concern of unit not heating and making loud noise. Found open hi limit causing no heat and seized idler pulley causing noise. Replaced hi limit, cut off and idler pulley. Ran air flow test, failed. Removed crushed portion of vent behind dryer. Ran air flow test again, still failed. Advised customer that vent from back of dryer to outside needs to be cleaned asap. Unit functioning as designed. ; used 1 279769 (THERMAL CUTOFF), and 1 279640 (PULLEY,IDLER) from stock"

We serviced a

KENMORE DRYER-ELECTRIC

Model 110.870886

Near Tacoma, WA 98408

Cameron M.

Job Details: 07/06/2021

"Customer concern is that dryer door does not remain closed during operation. Found failed door catch. Causing door to not remain closed during operation. Needs new door catch. Installed new door catch, cycle tested all checks good. ; used 1 279570 (CATCH DOOR DRYER) from stock"

We serviced a

MAYTAG WASHER-FRONT LOA

Model MHW3505FW1

Near Eatonville, WA 98328

Cameron M.

Job Details: 07/06/2021

"Installed previously ordered door latch, cycle tested. All checks good."

We serviced a

GE RANGE

Model JGB720SEJ1SS

Near Graham, WA 98338

Branden W.

Job Details: 07/06/2021

Customer concern is that range intermittently powers off. Unit working at time of service. 120vac to range. Wall plug has tight connection. Checked all power point connections from plug to main control. Found loose connection at back panel connection. Reseated and secured connection. Advised to call if issue returns.

We serviced a

MAYTAG DRYER-ELECTRIC

Model MED3500FW0

Near Eatonville, WA 98328

Cameron M.

Job Details: 07/06/2021

Installed previously ordered door cycle tested all checks good.

We serviced a

SAMSUNG DRYER-ELECTRIC

Model DVE50R5400V/A3

Near Plano, TX 75023

Jacob P.

Job Details: 07/06/2021

"Customer concern of unit not heating. Found open heating element causing no heat. Replaced heating element. Test cycled, all checks ok. ; used 1 DC97-14486A (ELEMENT ASSEMBLY) from stock"

We serviced a

WHIRLPOOL DISHWASHER

Model DU943PWKB0

Near Plano, TX 75024

Jacob P.

Job Details: 07/06/2021

"Installed previously ordered spray arms. Test cycled, all checks ok."

We serviced a

GE WASHER-TOPLOAD

Model GTW220ACK6WW

Near Dallas, TX 75252

Jacob P.

Job Details: 07/06/2021

"Installed previously ordered inlet valve. Test cycled, all checks ok."

We serviced a

SAMSUNG DISHWASHER

Model DW80K7050UG/AA 02

Near Sumner, WA 98390

Branden W.

Job Details: 07/06/2021

Customer concern is that dishwasher makes loud noise at beginning of cycle. Found debris in drain pump causing noise. Removed debris. Cycle tested. All checks good.

We serviced a

KENMORE WASHER-FRONT LOA

Model 11047797800

Near Graham, WA 98338

Cameron M.

Job Details: 07/06/2021

"Installed sears provided door lock, cycle tested all checks good."

We serviced a

KITCHENAID DISHWASHER

Model KDPE334GPS0

Near Dallas, TX 75225

Jacob P.

Job Details: 07/06/2021

"Customer concern of unit not filling with water. Found debris stuck under float switch causing no fill. Removed debris. Test cycled, all checks ok."

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWC400XW3

Near McKinney, TX 75071

Jacob P.

Job Details: 07/03/2021

"Installed previously ordered motor, blower, pulley and belt. Test cycled, all checks ok."

We serviced a

KENMORE DRYER-ELECTRIC

Model 11066912690

Near Frisco, TX 75035

Jacob P.

Job Details: 07/03/2021

"Installed previously ordered motor, blower, pulley and belt. Test cycled, all checks ok."

We serviced a

LG DRYER-ELECTRIC

Model DLE5977S

Near Frisco, TX 75034

Jacob P.

Job Details: 07/03/2021

"Customer concern of dryer making squealing noise. Found seized idler pulley and rear rollers causing noise. Replaced idler pulley and rear rollers, cleaned and lubed front rollers. Test cycled, all checks ok. ; used 1 4560EL3001A (IDLER PULLEY), and 2 4581EL2002H (ROLLER ASSEMBLY) from stock"

We serviced a

KITCHENAID DISHWASHER

Model KUDS30FXSS8

Near Frisco, TX 75035

Jacob P.

Job Details: 07/03/2021

"Installed previously ordered control board and control panel. Test cycled, all checks ok."

We serviced a

SAMSUNG WASHER-FRONT LOA

Model WF209ANW/XAA

Near Frisco, TX 75034

Jacob P.

Job Details: 07/03/2021

"Customer concern of unit shaking. Found front left leveling leg up too high causing machine to be unbalanced. Leveled machine. Test cycled, all checks ok."

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model LER4634JQ1

Near University Place, WA 98467

Branden W.

Job Details: 07/02/2021

"Customer concern is that dryer does not start. Found open thermal fuse causing unit to not start. Replaced fuse and operating thermostat. Cycle tested. Good Temps. Poor airflow. Dryer duct from wall to outside should be cleaned soon. Advised to make sure dryer is not pushed back too far at vent is getting crushed. ; used 1 WP3392519 (FUSE-THRML), and 1 WP3387134 (THRMST-FIX) from stock"

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWB865GW0

Near Allen, TX 75002

Jacob P.

Job Details: 07/02/2021

"Customer concern of ui board unresponsive. Test cycled, unit functioning fine. Performed key encoder test, all checks ok. Unable to verify complaint, unit functioning as designed."

We serviced a

WHIRLPOOL DISHWASHER

Model WDTA50SAHW0

Near Bonney Lake, WA 98391

Cameron M.

Job Details: 07/02/2021

"Customer concern is that dishwasher top rack adjusters broke. Found broken adjusters on top rack, causing rack to drop. Installed new adjusters, cycle tested all checks good. ; used 1 W10712395 (ADJUSTER) from stock"

We serviced a

KENMORE DISHWASHER

Model 66515939000

Near Graham, WA 98338

Branden W.

Job Details: 07/02/2021

Customer concern is that water leaks from airgap when dishwasher is draining. Filled dishwasher and it did not drain at all. Cleaned all hoses and pump housing. Reassembled. Tested again. Dishwasher draining good. Found no leak or overflow from airgap. Cleaned hose from airgap to sink drain anyway. Cycle tested dishwasher x5. All checks good. No mechanical issues found.

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWX655DW1

Near Puyallup, WA 98374

Cameron M.

Job Details: 07/02/2021

"Customer concern is that washer does not spin properly and gave off burning smell. Was unable to duplicate customer concern, unit operating as designed. Advised customer on regular cleaning intervals. Also advised to call if issue persists."

We serviced a

FRIGIDAIRE DISHWASHER

Model FPHD2485NF1A

Near McKinney, TX 75071

Jacob P.

Job Details: 07/02/2021

"Customer concern of error and always on. Found float switch stuck causing unit to always drain. Reset float switch. Test cycled, all checks ok."

We serviced a

WHIRLPOOL DRYER-ELECTRIC

Model WED7000DW0

Near Tacoma, WA 98418

Cameron M.

Job Details: 07/02/2021

"Customer concern is that dryer does not heat. Preformed airflow test failed (red).found open heating element, causing unit to not heat. Installed new heating element. cycle tested,all checks good. Advised customer dryer duct needs to be cleaned asap, before regular use continues. ; used 1 279838 (ELEMENT,HEATER) from stock"

We serviced a

WHIRLPOOL RANGE

Model WFG320M0BS3

Near Dallas, TX 75206

Jacob P.

Job Details: 07/02/2021

"Installed previously ordered control board and temp probe. Test cycled, all checks ok."

We serviced a

GE DRYER-ELECTRIC

Model GTD45EASJ2WS

Near Graham, WA 98338

Cameron M.

Job Details: 07/02/2021

"Installed previously ordered door asm, cycle tested all checks good."

We serviced a

MAYTAG DRYER-ELECTRIC

Model MED3500FW0

Near McKinney, TX 75070

Jacob P.

Job Details: 07/01/2021

"Customer concern of unit making squeaking noise. Found seized idler pulley and dirty rollers. Replaced idler pulley, cleaned and lubed rollers. Test cycled, all checks ok. ; used 1 279640 (PULLEY,IDLER) from stock"

We serviced a

WHIRLPOOL DISHWASHER

Model WDT710PAHB1

Near Tacoma, WA 98465

Branden W.

Job Details: 07/01/2021

Customer concern is that dishwasher was leaking. Then would not power on. Found loose power connection at dishwasher causing no power. Replaced wire nut. Unit powers fine. Cycle tested dishwasher. Found that disposal under sink leaks water through disposal. Advised that disposal is cause of leak. Advised to not use unit leak is repaired. No other issues found with dishwasher.

We serviced a

KENMORE DRYER-GAS

Model 11076911692

Near Dallas, TX 75228

Jacob P.

Job Details: 07/01/2021

"Customer concern of unit not heating. Found open thermal fuse causing no heat. Replaced thermal fuse. Test cycled, all checks ok. ; used 1 WP3390719 (FUSE-THRML) from stock"

We serviced a

MAYTAG WASHER-TOPLOAD

Model MVWB880BW0

Near Gig Harbor, WA 98335

Branden W.

Job Details: 07/01/2021

Installed new inlet valve. Cycle tested. All checks good. Left failed part as it caused a water leak.