Near Spanaway, WA 98387
Jacob P.
Job Details:
10/17/2020
DISHWASHER GE GSD3300R20BB
"Installed previously ordered motor and sump assy and baffles. Test cycled, all checks ok"
Near Lake Tapps, WA 98391
Nick R.
Job Details:
10/17/2020
OTHER GE JVM1750DP2BB
Preformed pm check cycle tested all checks good
Near Gig Harbor, WA 98335
Branden W.
Job Details:
10/17/2020
DRYER-ELECTRIC SAMSUNG n/a
Customer is that dryer is making noise. Found right rear roller off of shaft and left rear roller worn. Replaced both rear rollers. Lubed front rollers and idler pulley. Vacuumed inside of dryer. Cycle tested. All checks good. ; used 2 DC97-16782A (DRUM ROLLER) from stock
Near Spanaway, WA 98387
Jacob P.
Job Details:
10/17/2020
RANGE SAMSUNG NE59J7630SG/AA
"Installed previously ordered infinite switch. Advised customer that steam clean cycle will only run for 20 minutes and self clean will run for 3 hours. Test cycled, all checks ok."
Near Enumclaw, WA 98022
Nick R.
Job Details:
10/17/2020
OTHER KENMORE 25328432809
Preformed pm check cycle tested all checks good
Near Puyallup, WA 98375
Jacob P.
Job Details:
10/14/2020
WALL OVEN KENMORE 79042003605
Customer concern of temps jumping sporadically on display. Found control board not reading temp probe correctly and temp probe ohms out of range. Needs new control board and temp probe. ; ordrng 1 316460201 (Control board) and 1 316217002 (Temp probe)
Near Tacoma, WA 98404
Branden W.
Job Details:
10/14/2020
DRYER-ELECTRIC SAMSUNG DVE50M7450W/A3
Customer concern is that lint screen housing cracked and is snagging clothes. Needs new housing. ; ordrng 1 DC97-16741B (ASSY COVER FILTER) and 1 DC97-16742A (ASSY CASE FILTER)
Near Gig Harbor, WA 98335
Nick R.
Job Details:
10/14/2020
WASHER-TOPLOAD KENMORE 11015842400
"Customer concern that washer is making a grinding sound. Found a broken gear inside the transmission and a worn clutchand coupler , needs new transmission and clutch, and coupler. ; ordrng 1 3360629 (Gear case assy) and 1 285785 (Clutch) and 1 285753A (Coupling)"
Near Tacoma, WA 98499
Jacob P.
Job Details:
10/14/2020
WASHER-TOPLOAD GE GTW680BSJ4WS
Customer concern of unit leaving clothes wet at end of cycle. Found worn suspension rods causing machine to go out of balance. Needs new suspension rods. ; ordrng 2 WH16X26911 (Left suspension rod)s and 2 WH16X26910 (Right suspension rod)s
Near Tacoma, WA 98409
Jacob P.
Job Details:
10/14/2020
DISHWASHER GE GDF530PGM0WW
"Customer concern of unit leaking and door seal came out. Reinstalled door seal. Cleaned lower door seal, leveled and secured machine properly. Customer also stated the top rack falls sometimes. Found cap on left side broken and wheel missing from right rack. Needs new left slide and roller assy. Slide out of stock, AHS to supply parts. ; ordrng 1 WD12X22801 (Roller assy) and 1 WD30X25058 (Left slide)"
Near Puyallup, WA 98374
Nick R.
Job Details:
10/14/2020
DRYER-ELECTRIC SAMSUNG DV5086K00EV/A3 01
"Customer concern that dryer makes a lot of noise. Found both back roller seized causing dryer to make a lot of noise, needs two new back rollers. Installed new back rollers cycle tested all checks good ; used 2 DC97-16782A (DRUM ROLLER) from stock"
Near DuPont, WA 98327
Jacob P.
Job Details:
10/14/2020
WASHER-FRONT LOA WHIRLPOOL WFW94HEXL2
"Customer concern of unit not filling or agitating after starting cycle. Uninstaller MCU, found burnt spot. Needs new MCU.; ordrng 1 WPW10374126 (MCU)"
Near Lakewood, WA 98498
Jacob P.
Job Details:
10/14/2020
COOKTOP WHIRLPOOL WCE55US0HB01
"Customer concern that FL, RL and RR burners all turn off and turn back on periodically and FR burner always stays on. Advised customer that burners will cycle on and off to maintain temperatures. Cycle tested temps on burners, checks ok. Advised customer that machine is functioning as designed."
Near Tacoma, WA 98407
Jacob P.
Job Details:
10/14/2020
DRYER-ELECTRIC ELECTROLUX EFME417SIW0
Customer concern was that dryer was making a squeaky and thumping noise. Disassembled dryer and checked components. Lubricated drum rollers and pulley idler. Leveled dryer and test cycled. All checks ok.
Near Graham, WA 98338
Branden W.
Job Details:
10/14/2020
DRYER-ELECTRIC SAMSUNG DV45H7000EW/A2 02
Customer concern that dryer stops and produces HE (overheating) error. Unit has good airflow. Cycle tested temperatures 20 plus times. 155deg high. 125 low. Found no failures with dryer. Unable to reproduce error. Advised to make sure lint screen is cleaned each use and dryer is not overloaded. Dryer operating as designed at this time.
Near Puyallup, WA 98371
Nick R.
Job Details:
10/14/2020
DRYER-ELECTRIC SAMSUNG DV520AEP/XAA
Installed new heating element cycle tested all checks good.
Near University Place, WA 98467
Nick R.
Job Details:
10/14/2020
WASHER-TOPLOAD AMANA NTW4700YQ1
Preformed pm check cycle tested all checks good
Near Tacoma, WA 98406
Jacob P.
Job Details:
10/14/2020
DRYER-ELECTRIC WHIRLPOOL WED8500DC2
Installed previously ordered part. Ran test cycle. Air flow check came up yellow. Informed customer that vents will have to be cleaned soon.
Near Federal Way, WA 98023
Branden W.
Job Details:
10/14/2020
WASHER-TOPLOAD MAYTAG MVWB765FW3
Installed new lid. Cycle tested lock. All checks good.
Near Tacoma, WA 98406
Branden W.
Job Details:
10/14/2020
RANGE GE JB480DM1WW
Customer concern is that after running the clean cycle the oven will not turn on. Found manual door lock microswitch stuck in the locked position causing unit to not bake. Moving the lock lever a few times freed the switch. Unit now working good. Cycle tested to 250deg.
Near Graham, WA 98338
Branden W.
Job Details:
10/14/2020
DISHWASHER KENMORE 66513032K110
Installed new wash arm. And door seal. Cycle tested all checks good.
Near Fircrest, WA 98466
Nick R.
Job Details:
10/14/2020
COOKTOP OTHER NGM5054UC
Preformed pm check cycle tested all checks good
Near Graham, WA 98338
Branden W.
Job Details:
10/14/2020
RANGE WHIRLPOOL WFG530S0ES1
Customer concern is that oven does not ignite. Found poor connection on bake ignitor. Secured connection. Cycle tested x25. Unit igniting every time. Pre heated to 250deg. All checks good. Collected 75.00 deductible via card.
Near Tacoma, WA 98445
Nick R.
Job Details:
10/14/2020
WASHER-FRONT LOA KENMORE 79641262610
Preformed pm check cycle tested all checks good
Near Tacoma, WA 98404
Branden W.
Job Details:
10/14/2020
OVEN/STOVE GE JGBP85WEB1WW
Customer concern is that oven does not ignite when baking. Found failed bake ignitor causing no ignition. Needs new ignitor. Next service 10/19 1-5; ordrng 1 WB2X9154 (igniter)
Near Tacoma, WA 98445
Nick R.
Job Details:
10/14/2020
RANGE ELECTROLUX EW30GC55GS1
Customer concern that down draft knob is broken. The work order was for the range. Cycle tested range all checks good
Near Lake Tapps, WA 98391
Nick R.
Job Details:
10/14/2020
DISHWASHER KENMORE 66513213K901
Preformed pm check cycle tested all checks good
Near Enumclaw, WA 98022
Nick R.
Job Details:
10/14/2020
WASHER-FRONT LOA WHIRLPOOL WFW75HEFW0
Preformed pm check cycle tested all checks good.
Near Milton, WA 98354
Nick R.
Job Details:
10/14/2020
OTHER KENMORE 10671252101
Preformed pm check cycle tested all checks good
Near Puyallup, WA 98371
Nick R.
Job Details:
10/14/2020
OTHER GE 363FUF21DLRWW
Preformed pm check cycle tested all checks good
Near Fircrest, WA 98466
Branden W.
Job Details:
10/14/2020
COOKTOP KENMORE 91132389890
Customer concern is that Cookson ignitor will randomly spark even when cooktop is not in use. Unit has 120v with proper polarity. Found burner switch intermittently shorting at spark module causing random ignition at ignitors. Needs new switches and spark module. AHS auth needed. Closed garage door when leaving as requested by customer. ; ordrng 4 WB24T10071 (switch gas valve)s and 1 WB13K25 (spark module)
Near Tacoma, WA 98403
Nick R.
Job Details:
10/14/2020
DRYER-ELECTRIC SAMSUNG DV56H900EP4/A2
Customer concern that dryer is making a squealing sound. Found dryer with a seized idler pulley causing noise. Needs new idler pulley . Installed new idler pulley cycle tested all checks good. ; used 1 DC93-00634A (IDLER ASSEMBLY) from stock
Near Puyallup, WA 98371
Nick R.
Job Details:
10/14/2020
WASHER-TOPLOAD LG 796WT1901CK
Preformed pm check cycle tested all checks good
Near Puyallup, WA 98375
Branden W.
Job Details:
10/14/2020
WASHER-FRONT LOA LG WM8100HVA
Customer concern is that bedding and rugs do not spin out fully and washer has high pitch noise when filling. Advised that bedding and rugs have the highest tendency to be out of balance and not achieve a high speed spin. Advised to balance loads as best as possible to help achieve proper spin speeds. Also advised high water pressure is causing noise when filling. Turned hot supply down slightly to reduce noise. Washer ops as designed.
Near Puyallup, WA 98371
Nick R.
Job Details:
10/14/2020
DISHWASHER KENMORE 66514793N510
Preformed pm check cycle tested all checks good
Near Tacoma, WA 98408
Branden W.
Job Details:
10/14/2020
DISHWASHER AMANA ADB1400AGW0
Customer concern is that dishwasher does not drain the water. Found piece of ceramic lodged in pump impeller causing no drain. Cleaned pump. Cycle tested x3. All checks good. Collected 75.00 deductible via card.
Near Puyallup, WA 98375
Jacob P.
Job Details:
10/10/2020
WASHER-TOPLOAD SAMSUNG WA54M8750AV/A4
"Customer concern of grinding sound while spinning. Found debris between tub and basket causing sound. Removed debris. Test cycled, all checks ok."
Near Lakewood, WA 98498
Nick R.
Job Details:
10/10/2020
DRYER-ELECTRIC KENMORE 11085866400
Preformed pm check cycle tested all checks good
Near Puyallup, WA 98371
Nick R.
Job Details:
10/10/2020
WASHER-TOPLOAD KENMORE 11027092600
Preformed pm check cycle tested all checks good
Near , WA 98321
Nick R.
Job Details:
10/10/2020
DISHWASHER KENMORE 66514743N510
Preformed pm check cycle tested all checks good
Near Puyallup, WA 98374
Branden W.
Job Details:
10/10/2020
DISHWASHER FRIGIDAIRE FFID2426TD1A
Customer concern is that dishwasher will not drain. Found solid debris chunk clogging drain hose at pump outlet causing poor drain. Cleared debris. Cycle tested x3. All checks ok.
Near Tacoma, WA 98404
Branden W.
Job Details:
10/10/2020
DISHWASHER WHIRLPOOL WDF520PADB7
Customer concern that dishwasher will not power on. Found GFCI that dishwasher plugs into tripped. Unable to reset GFCI. Cycle tested dishwasher on different outlet. All checks good. Advised that an electrician is needed to restore power to outlet behind dishwasher. Left power cord in front of dishwasher with toe panel off at customers request.
Near Tacoma, WA 98403
Branden W.
Job Details:
10/10/2020
DRYER-GAS KENMORE GGW9200LQ1
Customer concern is that dryer does not heat at all. Found after several ignition cycles. Gas valve coils fail to open causing no heat. Replaced coils. Vacuumed inside of dryer. Also found moisture sensor bars unplugged. Reconnected sensors. Cleaned and tested sensors. Cycle tested. All checks ok. ; used 1 279834 (2 COIL GAS VALVE SET) from stock
Near Tacoma, WA 98404
Nick R.
Job Details:
10/10/2020
RANGE WHIRLPOOL WFC310S0EB
Customer concern that front left burner stays on high even when set on low. Found range with a stuck infinite switch cause front left burner to always be on high. Needs new infinite switch.; ordrng 1 WP3148952 (Infinite switch)
Near Puyallup, WA 98373
Jacob P.
Job Details:
10/10/2020
WALL OVEN FRIGIDAIRE FGET3065PFD
"Installed previously ordered bake element. Found burnt connector to bake element. Replaced connector. Test cycled, all checks ok."
Near Sumner, WA 98391
Branden W.
Job Details:
10/10/2020
DRYER-ELECTRIC WHIRLPOOL RED4440VQ1
Installed new timer. Cycoe tested on timed and auto dry setting. Good Temps and airflow. All checks good.
Near Tacoma, WA 98443
Nick R.
Job Details:
10/10/2020
OTHER KITCHENAID KBSN608EBS01
Preformed pm check cycle tested all checks good
Near Buckley, WA 98321
Branden W.
Job Details:
10/10/2020
DRYER-ELECTRIC GE GTD75ECPL0DG
Installed new front bearing and rear bearing. Test cycled with a load for 20 minutes. All checks ok.
Near Tacoma, WA 98446
Branden W.
Job Details:
10/10/2020
DRYER-ELECTRIC MAYTAG MEDC215EW1
Installed new timer. Cycle tested. Alo checks good.
Near Tacoma, WA 98418
Nick R.
Job Details:
10/10/2020
DRYER-ELECTRIC SAMSUNG DV45H7000EW/A2 02
Customer concern that dryer isn't drying. Found dryer with an open heating element causing dryer not to heat needs new heating element ; used 1 DC97-14486A (ELEMENT ASSEMBLY) from stock
Near Tacoma, WA 98408
Nick R.
Job Details:
10/10/2020
OTHER KENMORE 79571079010
Preformed pm check cycle tested all checks good.
Near Spanaway, WA 98387
Nick R.
Job Details:
10/10/2020
DRYER-ELECTRIC KENMORE 11065922401
"Customer concern that dryer isn't working. Found broken belt causing dryer not to work needs new belt, installed new belt cycle tested all checks good ; used 1 661570V (BELT) from stock"
Near Puyallup, WA 98372
Jacob P.
Job Details:
10/10/2020
DISHWASHER MAYTAG MDB4949SDE2
"Customer concern of unit not washing dishes well. Found sump disassembled and lower spray arm broken upon arrival. Found spray arms filled with debris and upper manifold warped. Needs new sump assy, lower spray arm, upper spray arm and upper manifold. Called asurion to inform them of condition of machine, they advised they are sending call in for review on whether the repair will be covered or not. ; ordrng 1 WPW10591570 (Sump assy) and 1 W10803178 (Lower spray arm) and 1 WPW10571946 (Upper manifold) and 1 WPW10605345 (Upper spray arm)"
Near Lakewood, WA 98499
Branden W.
Job Details:
10/10/2020
WASHER-FRONT LOA WHIRLPOOL WFW75HEFW0
Customer concern that washer powers on. Then goes blank. Washer then started working again. Unable to reproduce issue at time of service. Reseated interface connections. Cycle tested. No issues found at this time. Advised to call if issue returns.
Near Enumclaw, WA 98022
Nick R.
Job Details:
10/10/2020
OTHER LG LFC22770ST
Preformed pm check cycle tested all checks good.
Near Auburn, WA 98001
Nick R.
Job Details:
10/10/2020
RANGE GE JBP30BA2AD
Installed new infinite switch and power cord cycle tested all checks good
Near Puyallup, WA 98371
Branden W.
Job Details:
10/10/2020
WASHER-TOPLOAD KENMORE 11022622100
"Customer concern is washer makes a clunking noise and moved when washing towels. Advised clunking is normal sound when break releases. Found transmission leaking a lot of oil. Also found dog agits worn. Needs new transmission, clutch, coupler and dog agits. Next service 10/15 1-5pm; ordrng 1 3360629 (gear case) and 1 285753A (coupling,motor) and 1 285785 (clutch) and 1 80040 (agitator dogs)"
Near Puyallup, WA 98371
Nick R.
Job Details:
10/10/2020
DRYER-ELECTRIC SAMSUNG DV520AEP/XAA
Customer concern that dryer isn't heating. Found an open heating element causing dryer not to heat. Needs new heating element. Needs auth ; ordrng 1 DC93-00154A (Heating element)
Near Puyallup, WA 98371
Nick R.
Job Details:
10/10/2020
DRYER-ELECTRIC WHIRLPOOL WED4815EW1
"Customer concern that dryer stops mid cycle. Found the dryers timer with worn contacts causing dryer to stop mid cycle, needs new timer. ; ordrng 1 WPW10185982 (Timer)"
Near Gig Harbor, WA 98335
Jacob P.
Job Details:
10/10/2020
DISHWASHER WHIRLPOOL GU2400XTPQ7
"Customer concern of soap left on dishes and around dispenser. Tested water temps at sink, 125deg. Ran machine on normal, both spray arms moving. Test cycled drain, checks ok. Found no rinse aid in unit. Advised customer that rinse aid is required to achieve proper wash and drying results. Machine functioning as designed, no mechanical failure."
Near Tacoma, WA 98403
Jacob P.
Job Details:
10/10/2020
DISHWASHER KENMORE 58714153402
"Customer concern of unit not filling. Tested voltage to inlet valve, 120v. Checked valve under sink is open, checks ok. Test cycled machine, unit fills. Test cycled ×3, all checks ok."
Near Steilacoom, WA 98388
Branden W.
Job Details:
10/10/2020
DISHWASHER LG LDT7797BM
Customer concern is that dishwasher was failing to power on. Dishwasher started working again after days of not powering on. Unable to get unit to fail at time of service. Inspected console connections for corrosion. None found. Reseated all connections in console. Advised to call if issue returns.
Near Tacoma, WA 98443
Branden W.
Job Details:
10/10/2020
DISHWASHER KITCHENAID KDTE334DSS0
Customer concern is that dishes still wet and greasy at end of cycle. Found errors F8 E1 and F6 E1 Stored. Cycle tested. Found diverter motor does not stop running. Also found wash pump fails to start intermittently. Needs new sump assembly. Part is on manufacturer back order with no ETA. AHS to supply part. Dishwasher not grounded and power connection box cover missing. Lower toe panel missing clips. Zip tied on. ; ordrng 1 WPW10455261 (pump&motor)
Near Tacoma, WA 98404
Jacob P.
Job Details:
10/10/2020
DISHWASHER GE GSD2100V55WW
"Customer concern of unit leaking from left side when doing dishes in sink. Found unit full of water upon arrival. Drained water out, sink backed up completely. Unable to turn on garbage disposal. Drained unit into sink directly, drained fine. Advised customer that plumbing issue is causing sink to back up and back flow into dishwasher causing unit to overflow. Plumber is needed, dishwasher functioning as designed."
Near Enumclaw, WA 98022
Nick R.
Job Details:
10/10/2020
DRYER-ELECTRIC SAMSUNG DV45K6200EW/A3 02
Customer concern that dryer is making a wobbling sound found all 4 rollers worn causing a wobbling sound needs 4 new rollers. Installed new rollers cycle tested all checks good.; used 4 DC97-16782A (DRUM ROLLER) from stock
Near Spanaway, WA 98387
Nick R.
Job Details:
10/10/2020
WASHER-TOPLOAD MAYTAG MVWB765FFW3
Customer concern that clothes are getting stuck under the washplate. Found a shirt under the washplate . Removed shirt cycle tested all checks good
Near Tacoma, WA 98445
Branden W.
Job Details:
10/10/2020
WASHER-FRONT LOA SAMSUNG WF45M5500AZ/A5
Customer concern that washer leaks in front. Cycle tested x3 in rinse cycle. Only leak found was at door boot and glass seal. Cleaned hair and debris from door glass and boot. Cycle tested again. No leaks. Found no other signs of leaks. Advised to keep door glass and boot cleaned.
Near Auburn, WA 98001
Branden W.
Job Details:
10/10/2020
RANGE GE JBP30BA2AD
Tech was assigned as a helper;
Near Puyallup, WA 98373
Nick R.
Job Details:
10/10/2020
WASHER-FRONT LOA SAMSUNG WA54M8750AV/A4
Installed new drain hose cycle tested all checks good
Near Lakewood, WA 98498
Branden W.
Job Details:
10/10/2020
DISHWASHER MAYTAG MDB4949SDM0
Customer concern that door seal came off and dishwasher leaks. Needs new door seal. Next service 10/14 15pm; ordrng 1 W11177741 (gasket)
Near Tacoma, WA 98499
Jacob P.
Job Details:
10/10/2020
RANGE MAYTAG PER5750QAW
"Customer concern is that front left burner not turning on, and front right burner staying on high. Checked front right burner and infinite switch has bad contacts causing burner to always be high. Front left surface element is receiving proper voltage and coil is broken. Found loose handle on oven door. Need to replace flex infinite switch and replace surface element and tighten handle. Customer wants to think about repair."
Near Tacoma, WA 98445
Nick R.
Job Details:
10/10/2020
OTHER SAMSUNG RF34H9960S4
Preformed pm check cycle tested all checks good
Near Tacoma, WA 98406
Jacob P.
Job Details:
10/10/2020
DRYER-ELECTRIC MAYTAG MEDB765FC0
"Installed foam seal. Test cycled, all checks ok."
Near Gig Harbor, WA 98335
Jacob P.
Job Details:
10/10/2020
WASHER-FRONT LOA KENMORE 79641382410
Installed previously ordered stator assembly. Test cycled all checks ok.
Near Tacoma, WA 98409
Nick R.
Job Details:
10/10/2020
LAUNDRY CENTER FRIGIDAIRE FEX831CS0
Installed previously ordered parts cycle tested all checks good
Near , WA 98328
Branden W.
Job Details:
10/10/2020
WASHER-FRONT LOA KENMORE 79641162410
Customer concern is that washer leaks from door. Found debris causing leak at door boot and glass connection. Cleaned door glass and boot. Cycle tested. No leaks. Also cleaned clogged inlet filter causing washer to not fill with cold water.
Near Spanaway, WA 98387
Branden W.
Job Details:
10/10/2020
DRYER-ELECTRIC MAYTAG MEDX600XW0
Customer concern is that dryer does not heat. Found open heating element causing no heat. Replaced element. Vacuumed inside of dryer. Cycle tested. All checks good. ; used 1 WP3387747 (ELEMENT) from stock
Near Tacoma, WA 98446
Jacob P.
Job Details:
10/10/2020
LAUNDRY CENTER KENMORE 41761733810
"Installed previously ordered drain pump. Test cycled, all checks ok. Customer concern was that the dryer was making a loud nice. Found pulley shifted out of alignment. Reposition pulley, test cycled and all checks ok."
Near Lakewood, WA 98498
Jacob P.
Job Details:
10/10/2020
RANGE MAGIC CHEF CER1160AAH
"Customer concern of unit feeling warm whenever breaker is on. Found 116v sent to broil element even when unit is off causing unit to heat when not in use. Needs new thermostat. ; ordrng 1 WP74009379 (Thermostat), states that autho needed"
Near Orting, WA 98360
Nick R.
Job Details:
10/10/2020
RANGE WHIRLPOOL FEF368GCH
Customer concern that range cuts off by itself. And when its off the knob to the burner can turn it back on. Cycle tested oven couldn't verify issue advised customers they might have a weak breaker. Everything works as intended.
We serviced a
WASHER-FRONT LOA SAMSUNG WF45M5500AZ/A5 "Customer concern that washer will not spin. Cycle tested empty and with a load towels. Unit shakes causing spin cycle to fail. Recalibrated washer. Retested with load. Unit gets to 500 rpms then restarts cycle. Errors Dc. Bc2. Dc. Ub. Dc. Bc2. Ub. Store
Near Buckley, WA 98321
Branden W.
Job Details:
10/10/2020
Rear)s and 2 DC66-00470A (DAMPER SHOCK;FRONT)s and 1 DC31-00098A (MOTOR BLDC-ASSY HALL SENSOR) and 1 DC93-00278A (ASSY MODULE;MEMS SENSOR) and 1 DC92-01982A (ASSY PCB KIT)"
Near Orting, WA 98360
Branden W.
Job Details:
10/07/2020
DISHWASHER WHIRLPOOL WDT730PAHZ0
Customer concern that after last repair (upper rack adjuster kit on 7/20/20) dishwasher leans forward from cabinet. Found stick on mounting pads came off of solid surface counter tops. Advised this is an installation issue not a failure of the dishwasher. Advised to have a proper solid surface dishwasher mount installed. No mechanical failures of dishwasher.
Near Graham, WA 98338
Jacob P.
Job Details:
10/07/2020
DISHWASHER AMMNA n/a
"Installed previously ordered wash pump and grommet. Test cycled, all checks ok. When uninstalling unit, cracked fascia laminate. Glued crack back into place, customer okay with repair."
Near Lakewood, WA 98498
Jacob P.
Job Details:
10/07/2020
DRYER-ELECTRIC SAMSUNG DV50K7500EV-A3 01
"Installed previously ordered motor assembly. Test cycled with load, all checks ok."
Near Lakewood, WA 98498
Jacob P.
Job Details:
10/07/2020
WASHER-TOPLOAD SAMSUNG WA50M7450AW/A4
"Installed previously ordered stator assembly. Test cycled, all checks ok."
Near DuPont, WA 98327
Nick R.
Job Details:
10/07/2020
DRYER-ELECTRIC SAMSUNG DV42H5200EF/A3 03
Customer concern that dryer is making a loud noise. Found both back roller seized causing dryer to make a loud sound needs 2 new back rollers. Installed two new back rollers cycle tested all checks good.; used 2 DC97-16782A (DRUM ROLLER) from stock
Near Lakewood, WA 98498
Nick R.
Job Details:
10/07/2020
DRYER-ELECTRIC SAMSUNG DV50K8600EV/A3 01
"Customer concern that dryer is making a weird sounds found a worn idler pulley and both back roller are seized causing dryer to make a lot of noise. Needs new idler pulley and both back rollers. Installed rollers and idler pulley cycle tested all checks good.; used 2 DC97-16782A (DRUM ROLLER), and 1 DC93-00634A (IDLER ASSEMBLY) from stock"
Near Spanaway, WA 98387
Nick R.
Job Details:
10/07/2020
WASHER-TOPLOAD GE GTW460ASJ9WW
"Customer concern that washers lid lock is broken. Found washer with a broken lid lock causing washer to not spin needs new lid lock, install new lid lock cycle tested all checks good. ; used 1 WH01X27954 (Lid lock) from stock"
Near Puyallup, WA 98372
Branden W.
Job Details:
10/07/2020
DRYER-ELECTRIC SAMSUNG DV42H5200EP/A3 03
Customer stated they canceled appointment. Do not need service.
Near Tacoma, WA 98406
Jacob P.
Job Details:
10/07/2020
WASHER-TOPLOAD MAYTAG MVWB765FC3
"Installed previously ordered control board. Test cycled, all checks ok."
Near Graham, WA 98338
Branden W.
Job Details:
10/07/2020
WASHER-FRONT LOA SAMSUNG WF45K6500AV/A2 11
Customer concern that washer leaking water and suds from rear vent. Advised that too much soap build up from detergent overuse and not running clean washer cycle will cause this issue. Test cycled washer. No mechanical issues found. Advised to run clean washer cycle at least once a month and to only use 2 table spoons of HE detergent.
Near Puyallup, WA 98373
Nick R.
Job Details:
10/07/2020
DRYER-ELECTRIC SAMSUNG DV40J3000EW/A3 01
"Customer concern that dryer isn't heating. Found dryer with an open heating element causing dryer not to heat needs new heating element, installed new heating element cycle tested all checks good ; used 1 DC97-14486A (ELEMENT ASSEMBLY) from stock"
Near Tacoma, WA 98404
Nick R.
Job Details:
10/07/2020
DISHWASHER KENMORE 65513012K113
"Customer concern that dishwasher is leaking from bottom door seal and has bad smell, also the bottom rack starting to rust. Cycle tested dishwasher, dishwasher has good spray pressure and in coming water temps 120. Cleaned grime from door seal unable to get unit to leak advised that rust on rack is not covered. Dishwasher in need of cleaning advised to run several clean cycles. No mechanical failures found."
Near Puyallup, WA 98372
Branden W.
Job Details:
10/07/2020
WASHER-TOPLOAD LG WT1101CW
Customer concern that washer leaks from rear left corner. Cycle tested washer extensively. No leaks from any hoses. Washer is very rusted. Needs a complete overhaul. Water sitting in base pockets on left side. Shocks are weak and rusted. This is likely allowing washer tub to sit to low when filling dispensers and this causes splash over into washer base. Advised that rust damage is not covered. Extensive amount of rust caused by bleach. Collected 75.00 deductible via card.
Near Tacoma, WA 98406
Nick R.
Job Details:
10/07/2020
WASHER-TOPLOAD KENMORE 11028002010
Installed new lid lock cycle tested all checks good
Near Tacoma, WA 98409
Nick R.
Job Details:
10/07/2020
RANGE HOTPOINT RB525V4WH
Install new recept and bake element cycle tested all checks good
Near Tacoma, WA 98404
Nick R.
Job Details:
10/07/2020
WASHER-FRONT LOA MAYTAG MHW6630HW0
Install new board. As I was testing it board went out again. Needs new console and new control board.; ordrng 1 W11325572 (Console) and 1 W11322883 (Control board)
Near Bonney Lake, WA 98391
Branden W.
Job Details:
10/07/2020
DISHWASHER WHIRLPOOL WDTA50SAHZ0
Customer concern that dishwasher does not wash. Found 112v to wash pump. Wash pump is unresponsive. Neess new wash pump. ; ordrng 1 W11084656 (motor-pump) and 1 WPW10538166 (grommet)
Near Bonney Lake, WA 98391
Nick R.
Job Details:
10/07/2020
DRYER-ELECTRIC WHIRLPOOL WED8000DW3
Customer concern that dryers moisture sensors aren't working. Found a loose connection on the moisture sensor. Causing dryer not to work properly. Adjusted connection cycle tested all checks good.
Near Tacoma, WA 98409
Jacob P.
Job Details:
10/07/2020
DRYER-ELECTRIC SAMSUNG DV42H5000EW/A3
"Customer concern of unit not powering on and was making a squealing sound before. Found vent inside dryer disconnected causing excess of condensation buildup inside of dryer. Condensation inside control board and UI board caused shorts. Needs new control board, console, ui board and idler pulley. Could be further issues, unable to diagnose without being able to power on machine. ; ordrng 1 DC92-01596D (Control board) and 1 DC97-18106D (Console) and 1 DC92-01607H (UI board) and 1 Dc93-00634a (Idler pulley), states that autho needed"