We serviced a
GE DISHWASHER
Model GDT535PSMBSS
Near The Colony, TX 75056
John
Job Details: 01/26/2022
"Customer concern all buttons on dishwasher washer are unresponsive. Using newfi, found multiple ui errors stored. Test cycled wash and drain pumps, both receiving insufficient voltage to activate. Needs new ui board and control board.; ordrng 1 WD21X28609 (Ui board) and 1 WD21X29658 (Control board)"
We serviced a
KITCHENAID DISHWASHER
Model KDTE334GPS0
Near Frisco, TX 75034
John
Job Details: 01/26/2022
Installed previously ordered dispenser. Cycle tested all checks good.
We serviced a
GE DISHWASHER
Model PDT720SSH6SS
Near Frisco, TX 75034
John
Job Details: 01/26/2022
"Customer concern dishwasher tripping breaker even when not in use. Cycle tested unit, all checks good. Advised Customer electrician is required to correct issue."
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW7120HW0
Near Allen, TX 75013
John
Job Details: 01/26/2022
Customer concern washer going out of balance while washing and dropping black foam also the dispensar not functioning properly. Found plugged dispenser outlet causing detergent levels to read inaccurately. Cleared outlet. Checked suspension rods functioning properly. Found black rubber bumper pads worn causing black foam to be dropped from inside of machine. Advised Customer about washing more than one item at a time to fix balancing issue. Machine functioning as designed.
Near Allen, TX 75002
John
Job Details: 01/26/2022
Customer concern gas valve not turning at all. Found seized gas valve. Needs new gas valve.; ordrng 1 WB19T10084 (Gas valve)
We serviced a
GE WASHER-TOPLOAD
Model GTW460ASJ6WW
Near Plano, TX 75075
John
Job Details: 01/26/2022
"Customer concern washer dripping water when not in use. Found inlet valve not seating properly, causing dripping. Needs new inlet inlet valve.; ordrng 1 WH13X26535 (Inlet valve)"
We serviced a
KENMORE WASHER-FRONTLOAD
Model 79641262610
Near Dallas, TX 75235
Jorge
Job Details: 01/26/2022
Installed previously ordered drain hose tested unit and all checks good to manufacturer's proper functions
We serviced a
FRIGIDAIRE WASHER-TOPLOAD
Model GLWS1339ESO
Near Dallas, TX 75219
Jorge
Job Details: 01/26/2022
Customer concern washer leaking water .found an open solenoid on water valve. Causing water to leak into tub. Needs new water valve for proper functions ; ordrng 1 134211400 (Water valve)
We serviced a
GE DISHWASHER
Model PDT715SYN0FS
Near Dallas, TX 75231
Jorge
Job Details: 01/26/2022
Customer concern unit is leaking from the bottom right side. Found the wash motor cracked causing water to go through it. Needs the wash motor assembly for proper functions ; ordrng 1 WD19X25700 (Wash motor assembly)
We serviced a
GE WASHER-TOPLOAD
Model GTWN4250D0WS
Near Dallas, TX 75229
Jorge
Job Details: 01/26/2022
Customer concern that washer is not draining. Cycle tested unit also did the units self diagnostic procedures and was unable to verify complaint. All checks are good
We serviced a
GE WASHER-TOPLOAD
Model GFW550SSN0WW
Near Dallas, TX 75220
Jorge
Job Details: 01/26/2022
Installed previously ordered lock assembly. Tested unit and all checks good to manufacturer's proper functions
We serviced a
SAMSUNG WASHER-TOPLOAD
Model WA45N3050AW/A4
Near Dallas, TX 75212
Jorge
Job Details: 01/26/2022
Installed previously ordered lock assembly. Tested unit and all checks good
We serviced a
WHIRLPOOL DISHWASHER
Model GU2275XTVY1
Near Dallas, TX 75206
Jorge
Job Details: 01/26/2022
Customer concern unit leaking.found the door gasket worn down needs new gasket for proper functions ; ordrng 1 W10542314 (Door gasket)
We serviced a
KENMORE WASHER-FRONTLOAD
Model 110.429222
Near Dallas, TX 75214
Jorge
Job Details: 01/26/2022
Customer concern washer not working. Found the motor control board shorted out cause the washer to not drain or spin. Need to replace motor control board for proper functions ; ordrng 1 W10756692 (Motor board control)
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW6400SW3
Near Carrollton, TX 75007
Patrick
Job Details: 01/26/2022
"Customer concern, unit leaks large amount of water. Ran normal cycle with towels in basket. Good fill, good recirculation, good drain, no leak noted. Significant bearing noise from drive system during spin. Basket hanging off camber. Could cause fill water to miss basket. Must replace dampers. ; ordrng 1 W10820048 (Dampers)"
We serviced a
MAYTAG WASHER-TOPLOAD
Model LAT9416AAE
Near Carrollton, TX 75007
Patrick
Job Details: 01/26/2022
Replaced bleach hose. Tested unit. All checks good.
We serviced a
GE WALL OVEN
Model JT5000SF3SS
Near Rockwall, TX 75087
Patrick
Job Details: 01/26/2022
"Customer concern, f96 error code. Unit stops cooking. Verified 56 stored f96 errors. Ran turns but too slowly. Speed sensor does not register any rpm at all. Must replace fan assy and sensor. ; ordrng 1 WB27T11463 (Speed sensor) and 1 WB26X31060 (Cooling fan)"
We serviced a
WHIRLPOOL DISHWASHER
Model DO1030XTXS1
Near Rockwall, TX 75087
Patrick
Job Details: 01/26/2022
"Customer concern, unit tripping breaker. Breaker will not reset. Found control burned and melted, harness destroyed by fire. Must order harness and main control. All parts listed as backorder. ; ordrng 1 W10906417 (Control) and 1 WPW10348443 (Harness)"
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WF45R6100AC/US
Near Rowlett, TX 75089
Patrick
Job Details: 01/26/2022
"Customer concern, unit walking during spin. Found unit had moved about 1ft from set location on arrival. Ran spin cycle with empty drum. Some vibration during high spin. Found detached lower front counterweight. Found large hole in front tub where vounterweight detached. Must replace front tub and counterweight. Tub listed as NLA. LOWES TO RESEARCH PART.; ordrng 1 DC97-21448A (Front tub) and 1 DC67-00999A (Counter weight)"
We serviced a
FRIGIDAIRE DISHWASHER
Model LFBD2409LF3C
Near Rockwall, TX 75032
Patrick
Job Details: 01/26/2022
"Customer concern, not draining. Unit partially disassembled on arrival. Reassembled. Manual cancel, good drain. Ran quick cycle. Good fill, good spray, good dispenser, good drain. Cleaned filter, no vitally found at this time, unit checks all good"
We serviced a
GE DISHWASHER
Model GSD4020Z07BB
Near Heath, TX 75032
Patrick
Job Details: 01/26/2022
"Customer concern, unit not draining. Tub full of water on arrival. Solenoid operation good first two tries then no drain. Good drain when manipulated hand. Must race sump assy.; ordrng 1 WD26X10013 (Sump assy)"
We serviced a
GE WALL OVEN
Model JT5500SF3SS
Near Rockwall, TX 75032
Patrick
Job Details: 01/26/2022
"Customer concern, upper oven 50* low lower oven 25*low. No error codes. Bake, broil, and convect all function. Set at 350 convect. Confirmed good temps on 4 separate thermometers. Nofaultfound at this time. All checks good"
We serviced a
SAMSUNG WASHER-TOPLOAD
Model WA52M7750AV/A4
Near Gig Harbor, WA 98332
Cejay
Job Details: 01/26/2022
Installed previously ordered lid assembly. Verified functionality of the lid. All checks good
We serviced a
SAMSUNG RANGE
Model NE58K9560WS/AA03
Near Tacoma, WA 98404
Cejay
Job Details: 01/26/2022
Installed previously ordered main and sub PCB. Wire harness. Incorrect wire harness ordered.Wire harness DG96-00360A is the wire harness needed. DC signal wire. Part shows out of stock advised customer may take time to recive.; ordrng 1 DG96-00360A (ASSY WIRE HARNESS-DC SIGNAL)
We serviced a
MAYTAG DRYER-ELECTRIC
Model MEDE500VW1
Near Tacoma, WA 98422
Cejay
Job Details: 01/26/2022
Installed new user interface. Shs shipped duplicate user interface. Did not ship main control. Dryer still needs main control.; O-emld tckt
We serviced a
FRIGIDAIRE DISHWASHER
Model GLDB656JS0
Near Tacoma, WA 98406
Cejay
Job Details: 01/26/2022
"Installed previously ordered gasket, springs x2 and linkage x2 cycle tested unit. Is still leaking from bottom of door found torn sweeper seal. Needs new sweeper seal. Follow up scheduled for 02/01 8-12; ordrng 1 809006501 (Sweeper seal.)"
We serviced a
MAYTAG WASHER-FRONTLOAD
Model MHW5100DW0
Near Tacoma, WA 98404
Cejay
Job Details: 01/26/2022
"Customer concern is washer is not spinning. Door locked on arrival. Reset washer, mixed undersized load inside. Cycle tested unit empty with no issues. Cycle tested washer with 6 bath towels with no issues twice. All checks good. Advised customer on proper loading practices."
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW5000DW2
Near Puyallup, WA 98371
Cejay
Job Details: 01/26/2022
Customer concern is that washer is not spinning and is making a noise during operation. Found worn drive pully causing washer not to spin also causing noise during operation. Needs new drive pully. Follow up scheduled for 02/01 8-12pm; ordrng 1 W10721967 (drive pulley)
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WF45K6500AV/A2-11
Near Dallas, TX 75216
Jorge
Job Details: 01/25/2022
Customer concern washer not working. Found the start/pause button internally broken causing unit not to start wash.. need to replace panel for proper functions ; ordrng 1 DC97-20444C (Panel control assy) and 1 DC97-04973B (Boot spring)
We serviced a
FRIGIDAIRE WASHER-TOPLOAD
Model FFTW4120SW
Near Forney, TX 75126
Jorge
Job Details: 01/25/2022
Customer concern washer not draining. Found drain pump broken from the impeller causing water not to drain out. Needs drain pump replacement for proper functions ; ordrng 1 5304511361 (Drain pump)
We serviced a
FRIGIDAIRE DRYER-ELECTRIC
Model FFRE4120SW
Near Forney, TX 75126
Jorge
Job Details: 01/25/2022
Customer concern unit not working. Found the motor is shorted out. Needs motor for proper functions ; ordrng 1 5304511430 (Motor)
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW5000DW1
Near Rockwall, TX 75032
Jorge
Job Details: 01/25/2022
Installed previously ordered rods .tested unit and all checks good
We serviced a
GE DISHWASHER
Model GLD5950N00CS
Near Dallas, TX 75219
Jorge
Job Details: 01/25/2022
Installed previously ordered spray arms. Tested unit and all checks good
We serviced a
GE WASHER-TOPLOAD
Model WSLS1500H2WW
Near Dallas, TX 75209
Jorge
Job Details: 01/25/2022
Customer concern washer leaking. Found pressure switch stuck open causing unit to overfill. Water valve tested good. Need to replace pressure switch for proper functions ; ordrng 1 WH01X20601 (Pressure switch)
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW4816FW2
Near Grand Prairie, TX 75051
Patrick
Job Details: 01/25/2022
"Customer concern, unit makes loud noise during use. Not filling with enough water. Confirmed noise from motor area. Good fill level. Must replace belt and cam.; ordrng 1 WPW10006384 (Belt) and 1 W10721967 (Cam)"
We serviced a
GE DRYER-ELECTRIC
Model GTD42EASJ2WW
Near Dallas, TX 75211
Patrick
Job Details: 01/25/2022
"Customer concern, unit tracking several cycles to dry. Failed air flow test with vent attached, passed air flow test with bent removed. Clogged home vent. Recommend professional vent cleaning."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB765FW3
Near Duncanville, TX 75116
Patrick
Job Details: 01/25/2022
Replaced lid. Tested unit. All checks good
We serviced a
GE DISHWASHER
Model GLD5850L00CS
Near Mesquite, TX 75149
Patrick
Job Details: 01/25/2022
On site to replace drain pump and drain hose. Found shut off valve under sink will not turn off. Must have plumber address valve issue. Return trip needed after plumbing is repaired. ; O-emld tckt
We serviced a
GE RANGE
Model JS645SL3SS
Near Garland, TX 75041
Patrick
Job Details: 01/25/2022
"On site to replace element, infinite sw and glass top. Parts shipped to customer direct. Found element damaged in box. Glass top good. Must order both front elements as neither work. Also order infinite sw from previous order.; ordrng 2 WB30X24111 (Front elements)s"
We serviced a
GE DISHWASHER
Model GDT695SGJ0BB
Near Garland, TX 75040
Patrick
Job Details: 01/25/2022
Replaced drain hose. Unable to test unit. Must replace ui to restore operation first.
We serviced a
GE DISHWASHER
Model GDT695SMJ2ES
Near Spanaway, WA 98387
Cameron M.
Job Details: 01/25/2022
"Installed previously ordered drain pump, diverter and sump assembly. Cycle tested unit 3x. all checks good"
We serviced a
WHIRLPOOL WASHER-FRONTLOAD
Model WFW92HEFW0
Near Eatonville, WA 98328
Branden W.
Job Details: 01/25/2022
Customer concern is that washer will not drain and produces F9 E1 error. Found clogged drain pump causing unit to not drain. Cleared pump. Cycle tested. All checks ok.
We serviced a
WHIRLPOOL RANGE
Model WFE515S0ES0
Near Tacoma, WA 98408
Cameron M.
Job Details: 01/25/2022
"Installed previously ordered control board and temp sensor. Cycle tested unit, all checks good."
We serviced a
WHIRLPOOL DISHWASHER
Model DU1055XTPQ4
Near Tacoma, WA 98409
Branden W.
Job Details: 01/25/2022
Installed new latch and switches. Cycle tested. All checks good.
We serviced a
KENMORE WASHER-FRONTLOAD
Model 11024902200
Near Spanaway, WA 98387
Cameron M.
Job Details: 01/25/2022
"Customer concern is that washer does not spin. Found failed coupler, causing unit to not spin. Also found corroded and shorted motor wire connection. Needs new coupler and wire connector. Installed new coupler and wire connector. Cycle tested unit 10x. All checks good. Advised customer on using high quality detergent for best wash results. Also advised customer on regular cleaning intervals for optimal performance. ; used 1 285753A (COUPLING,MOTOR) from stock"
We serviced a
MAYTAG DRYER-ELECTRIC
Model MED5770TQ0
Near Tacoma, WA 98409
Branden W.
Job Details: 01/25/2022
Customer concern is that dryer takes extended time to dry. Airflow good. Tested temperatures on all heat options. Good temps. 160 high at exhaust. Cleaned moisture sensor. No issues found with dryer Atchison time.
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV42H5200EW/A3 04
Near Spanaway, WA 98387
Cejay
Job Details: 01/25/2022
"Customer concern is that dryer is making a noise during operation. Found debris wrapped around both rear wheels. Cleaned and lubed both rear wheels. Cycle tested unit, all checks good"
We serviced a
WHIRLPOOL RANGE
Model WEG745H0FS0
Near Lakewood, WA 98499
Cejay
Job Details: 01/25/2022
Installed previously ordered oven ignitors x2 wire harness and sparke module. Cycle tested unit it all checks good
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV42H5200EP/A3 03
Near Gig Harbor, WA 98335
Cejay
Job Details: 01/25/2022
"Installed previously ordered heater assembly, thermistor and support wheel. Cycle tested unit, all checks"
We serviced a
KENMORE WASHER-TOPLOAD
Model 11025864400
Near Ruston, WA 98407
Cejay
Job Details: 01/25/2022
Customer concern is that washer is not spinning during operation. Found failed motor causing washer not to operate intermittently. Needs new motor. Shs ships directly to customer. Advised customer to schedule follow up when parts are received.; ordrng 1 WP8529935 (MOTOR)
We serviced a
GE DRYER-ELECTRIC
Model GTD33EASKWW
Near Tacoma, WA 98418
Cejay
Job Details: 01/25/2022
"Customer concern is that dryer scraping sound during operation. Found debris stuck on glides. Removed debris, cycle tested unit it all checks good."
We serviced a
MAYTAG DRYER-ELECTRIC
Model MDEZ600TW2
Near Spanaway, WA 98387
Cejay
Job Details: 01/25/2022
"Installed previously ordered controll board. Cycle tested unit, all checks good."
We serviced a
LG DISHWASHER
Model LDF7774ST
Near Puyallup, WA 98372
Branden W.
Job Details: 01/24/2022
Customer concern is that dishwasher makes noise. Found failing bearing in wash pump motor causing noise. Needs new wash pump assembly. Declined to repair at this time.
We serviced a
MAYTAG DRYER-GAS
Model LDG9801AAW
Near Gig Harbor, WA 98332
Branden W.
Job Details: 01/24/2022
"Installed new glides, rollers, pulley and belt. Vacuumed inside of unit. Cycle tested. All checks good."
We serviced a
GE WASHER-TOPLOAD
Model GTW490ACJ4WW
Near Puyallup, WA 98375
Branden W.
Job Details: 01/24/2022
"Installed new washplate, belt, pulley and sensor. Cycle tested. All checks good"
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWC465HW2
Near Dallas, TX 75212
Jacob P.
Job Details: 01/24/2022
"Installed previously ordered control board. Test cycled, unit now runs. Found drain hose Installed below water level. Advised customer drain hose will need to be reinstalled at proper height for unit to run correctly. Unit functioning as designed."
We serviced a
GE RANGE
Model JB968S0H2SS
Near Spanaway, WA 98387
Branden W.
Job Details: 01/24/2022
Installed new faceplate with keypad. Tested all button functions. All checks good.
We serviced a
GE DISHWASHER
Model GLD5800L00WW
Near Rockwall, TX 75087
Jacob P.
Job Details: 01/24/2022
"Installed previously ordered motor. Test cycled, all checks ok."
We serviced a
KENMORE WASHER-TOPLOAD
Model 11023832100
Near Rowlett, TX 75089
Jacob P.
Job Details: 01/24/2022
"Customer concern of unit not draining. Found broken lid switch causing unit to not drain. Replaced lid switch. Test cycled, all checks ok. ; used 1 WP3949238 (SWITCH-LID) from stock"
We serviced a
AMANA WASHER-TOPLOAD
Model NTW4605YQ0
Near Tacoma, WA 98446
Branden W.
Job Details: 01/24/2022
Customer concern is that washer bangs in spin cycle when washing heavy loads. Cycle tested with 8 bath towels. Unit operating as designed. All mechanical components check good. Advised that bedding and water proof items will often need to be manually redistributed and a spin only cycle ran.
We serviced a
MAYTAG DISHWASHER
Model MDB8989SHZ0
Near Tacoma, WA
Branden W.
Job Details: 01/24/2022
Customer concern is that dishwasher does not operate. Dishes dirty and detergent not dissolved. Found loose connection at gord for wash pump. Secured connection. Cycle tested. Dishwasher operating as designed. Advised that water does siphon out as drain runs under floor and there is no high loop. Advised to add high loop and or a anti siphon device.
We serviced a
SAMSUNG DISHWASHER
Model DW80R5060UG/AA 00
Near Puyallup, WA 98375
Cameron M.
Job Details: 01/21/2022
"Installed previously ordered door switch, cycle tested unit 3x. All checks good. Advised customer on using high quality detergent for best wash results. Also advised customer on regular cleaning intervals for optimal performance."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAHZ0
Near Puyallup, WA 98372
Branden W.
Job Details: 01/21/2022
Customer concern is that dishwasher leaks again. Cycle tested through entire 1hr cycle. No leaks at this time. Advised to load differently and change to Finish detergent and to monitor and call if leak persists.
We serviced a
SAMSUNG RANGE
Model NX58H5600SS/AA
Near Roy, WA 98580
Branden W.
Job Details: 01/21/2022
"Customer concern is that when using bake, it sometimes does not heat up. If it does, it does not maintain temperature. Found bake ignitor only drawing 2.6 amps causing gas valve to not open and unit to not heat. Replaced bake ignitor. Cycle tested. All checks good. ; used 1 WB13K21 (OVEN IGNITER-12' LEAD W/NUTS) from stock"
We serviced a
WHIRLPOOL RANGE
Model RF366PXGQ 2
Near Roy, WA 98580
Cameron M.
Job Details: 01/21/2022
"Customer concern is that left front burner does not heat. Found corroded connection on infinite switch, causing unit to not heat. Needs new infinite switch. Repaired wire connection, installed new infinite switch. Cycle tested unit. All checks good. ; used 1 WP3149400 (SWITCH-INF), and 1 279457 (WIRE-SPADE) from stock"
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WF42H5000AW/A2 11
Near Spanaway, WA 98387
Cameron M.
Job Details: 01/21/2022
"Customer concern is that washer powers off mid cycle now does not power on. Found unit powers on but does not drain. Found debris in drain pump clean out, causing unit to not drain and spin. Cleaned out drain pump. Cycle tested unit. All checks good. Advised customer customer on using high quality detergent for best wash results. Also advised customer on regular cleaning intervals for optimal performance."
We serviced a
GE DISHWASHER
Model PDT720SSH6SS
Near Frisco, TX 75034
Jacob P.
Job Details: 01/21/2022
"Customer concern of unit tripping breaker. Test cycled all components, checks ok. Tested voltage to unit, found L1v and N lines swapped. Corrected polarity. Test cycled, all checks ok."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV45H7000EW/A2 01
Near Bonney Lake, WA 98391
Branden W.
Job Details: 01/21/2022
"Customer concern is that dryer does not heat. Found open heating element causing no heat. Also found seizing idler pulley. Replaced element and idler. Cleaned and lubed all rollers. Vacuumed inside of dryer. Performed airflow test (passed). All checks good. ; used 1 DC97-14486A (ELEMENT ASSEMBLY), and 1 DC93-00634A (IDLER ASSEMBLY) from stock"
We serviced a
GE DISHWASHER
Model DDT595SSJ4SS
Near Buckley, WA 98321
Branden W.
Job Details: 01/21/2022
Installed new wash pump. Cycle tested. All checks good.
We serviced a
WHIRLPOOL WASHER-FRONTLOAD
Model WFW92HEFC0
Near Buckley, WA 98321
Cameron M.
Job Details: 01/21/2022
"Installed previously ordered main control board and pressure switch. Cycle tested unit 3x, all checks good. Advised customer on using high quality detergent for best wash results. Also advised customer on regular cleaning intervals for optimal performance."
We serviced a
WHIRLPOOL WASHER-FRONTLOAD
Model WFW95HEDW0
Near Wylie, TX 75098
Jacob P.
Job Details: 01/20/2022
"Installed previously ordered drain pump. Test cycled, all checks ok."
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WF218ANB/XAA
Near Allen, TX 75002
Jacob P.
Job Details: 01/20/2022
Picked up part
We serviced a
GE DISHWASHER
Model GPT225SGL0BB
Near Puyallup, WA 98374
Branden W.
Job Details: 01/20/2022
Customer concern is that dishwasher tub seal came off. Reinstalled seal. Cycle tested. All checks ok.
We serviced a
GE WASHER-FRONTLOAD
Model n/a
Near Buckley, WA 98321
Cameron M.
Job Details: 01/20/2022
"Customer concern is that washer does not spin. Found basket support broken, causing basket to fall into tub. Needs full tub job, and door boot. unable to repair. Also Unable to obtain model and serial numbers to conduct part search or verification of unit."
We serviced a
WHIRLPOOL WALL OVEN
Model JKP2660V1BB
Near Rowlett, TX 75089
Jacob P.
Job Details: 01/20/2022
"Installed previously ordered handle caps. Test cycled, all checks ok."
We serviced a
KITCHENAID DISHWASHER
Model KUDPO2CRBS2
Near Allen, TX 75013
Jacob P.
Job Details: 01/20/2022
"Installed previously ordered door seal. Test cycled, all checks ok."
We serviced a
KENMORE DISHWASHER
Model 66512793K310
Near Gig Harbor, WA 98335
Branden W.
Job Details: 01/20/2022
Installed previously ordered parts. Cycle tested x2 in rinse and tested through service cycle. All checks good.
We serviced a
WHIRLPOOL RANGE
Model RF386PXGQ0
Near Buckley, WA 98321
Cameron M.
Job Details: 01/20/2022
"Installed previously ordered control board, cycle tested unit. All checks good"
We serviced a
LG WASHER-FRONTLOAD
Model WM3170CW
Near Gig Harbor, WA 98332
Branden W.
Job Details: 01/20/2022
Installed new drain pump. Also found cold water inlet screen partially plugged causing slow fill. Cleaned screen. Cycle tested. All checks good.
We serviced a
GE DRYER-ELECTRIC
Model GTD42EASJ2WW
Near University Place, WA 98466
Cameron M.
Job Details: 01/20/2022
"Installed previously ordered drum glides, cycle tested unit.all checks good. Preformed airflow test failed (red) Advised customer dryer vent duct needs to be cleaned asap before use resumes to prevent damage to element and other components."
We serviced a
KENMORE DRYER-ELECTRIC
Model 79681073310
Near Carbonado, WA 98323
Cameron M.
Job Details: 01/20/2022
"Installed sears provided control board. Cycle tested unit, all checks good. Preformed airflow test failed (yellow).cleand and calibrated moisture sensors. temperature checks ,in range."
We serviced a
MAYTAG DRYER-ELECTRIC
Model MISSING
Near Lakewood, WA 98499
Branden W.
Job Details: 01/14/2022
"Customer concern is that dryer does not heat. Found open heating element causing no heat. Also found burned terminal at element. Replaced element and terminal. All checks ok. No model or serial tag on unit. ; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #), used 1 279457 (WIRE-SPADE), and 1 279838 (ELEMENT,HEATER) from stock"
We serviced a
KITCHENAID DISHWASHER
Model KDFE104DSS1
Near Tacoma, WA 98422
Branden W.
Job Details: 01/14/2022
Customer concern is that dishwasher does not drain. Dishwasher disassembled prior to service. Toe panel clips missing. Advised missing parts are not covered. Found clogged airgap causing no drain. Cleaned air gap. Cycle tested x3. Unit operating properly.
We serviced a
MAYTAG DRYER-ELECTRIC
Model MEDC465HW0
Near Tacoma, WA 98404
Branden W.
Job Details: 01/14/2022
Customer concern is that dryer does not start. Found dryer motor stuck causing unit to not start. Found comb lodged in blower wheel causing motor to not operate. Cleared blower housing. All checks ok. Left dryer out at customers request so they can clean behind unit.
We serviced a
WHIRLPOOL RANGE
Model RF369LXPB1
Near Puyallup, WA 98375
Branden W.
Job Details: 01/14/2022
Installed new elements and receptacles. All checks good.
We serviced a
LG WALL OVEN
Model LWD3081ST/00
Near Tacoma, WA 98445
Cameron M.
Job Details: 01/14/2022
"Installed previously ordered pcb assembly, cycle tested unit. All checks good"
We serviced a
LG WASHER-TOPLOAD
Model WT5070CW
Near Milton, WA 98354
Cameron M.
Job Details: 01/13/2022
Customer concern is that washer leaves film on clothes and has brown film on tub. Cycle tested unit 3x found no mechanical issues. Unit operating as designed. Advised customer on using high quality detergent for best wash results. Also advised customer on importance of running cleaning cycle at regular intervals. Also advised customer on monitor and call if issue persists
We serviced a
LG DRYER-ELECTRIC
Model DLEX5170W
Near Milton, WA 98354
Cameron M.
Job Details: 01/13/2022
"Customer concern is that dryer takes multiple cycles to dry clothes. Preformed airflow test passed (green). Preformed temperature checks, in range. Found no mechanical issues with dryer at this time. Unit operating as designed.cleaned and calibrated moisture sensors. advised customer on monitor and call if issue persists"
We serviced a
LG RANGE
Model LRE3061BD/00
Near Spanaway, WA 98387
Branden W.
Job Details: 01/13/2022
Customer concern is that range displays F9 (Temps less than 150) error when using broil and taking much longer to pre heat. Tested and found broil element not producing heat. Found failed terminal connection at broil element causing no voltage to element. Replaced terminal. Cycle tested. Unit operating as designed.
We serviced a
GE RANGE
Model P2B918SEM3SS
Near Spanaway, WA 98387
Branden W.
Job Details: 01/13/2022
Installed new main control board supplied by AHS. Cycle tested. All checks ok at this time. This is the 3rd board in this unit in a few months. Unit should be replaced if new board fails.
We serviced a
AMANA WASHER-TOPLOAD
Model NTW4700YQ1
Near University Place, WA 98467
Cameron M.
Job Details: 01/13/2022
"Customer concern is that washer makes humming noise and not draining, found humming noise and no drain condition, causing by debris clogging drain hose not allowing pump to evaluate water from washer. Clear debris cycle tested unit 3x. All checks good."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV45H7000EP/A3
Near Spanaway, WA 98387
Branden W.
Job Details: 01/13/2022
"Customer concern is that dryer makes squealing noise. Found seized idler pulley and worn drum roller causing noise. Replaced idler pulley and right rear roller. Vacuumed inside of dryer. Cycle tested. All checks good. ; used 1 DC97-16782A (DRUM ROLLER), and 1 DC93-00634A (IDLER ASSEMBLY) from stock"
We serviced a
GE DISHWASHER
Model GSD6200G00WW
Near Puyallup, WA 98374
Branden W.
Job Details: 01/13/2022
"Customer concern is that dishwasher does not operate. Found no voltage to dishwasher. Breaker tripped. Reset breaker. Cycle tested, unit not filling with water. 0vac to inlet valve. 120vac into float switch. 0vac out. Float switch burned. Ohmed inlet valve, 0.0 ohms causing short. Needs new inlet valve and float switch. Declined to repair at this time"
We serviced a
KITCHENAID DISHWASHER
Model KUDS011JBS0
Near Tacoma, WA 98404
Branden W.
Job Details: 01/12/2022
"Customer concern is that after turning off then on main breaker to house, dishwasher will not operate. Found open fuse on main board. Installed new fuse and harness splice. Cycle tested fill, wash, drain and heat x3. All operating properly. ; used 1 8193762 (THERMAL FUSE-DISHWASHER) from stock"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAHZ0
Near Puyallup, WA 98375
Branden W.
Job Details: 01/12/2022
Customer concern is that dishwasher does not start. Found dishwasher fails to engage after pressing start or cancel. Reset control board. Cycle tested. All checks good.
We serviced a
SAMSUNG WASHER-FRONTLOAD
Model WF45R6300AV/US
Near Tacoma, WA 98405
Cameron M.
Job Details: 01/12/2022
"Customer concern is that washer makes noise during spin cycle. Cycle tested unit 10x, found no mechanical issues. Advised customer on proper loading practices. Also advised customer on regular cleaning intervals for optimal performance. Advised customer on using high quality detergent for best wash results."
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW4816FW2
Near Garland, TX 75041
Jacob P.
Job Details: 01/12/2022
"Installed suspension rods. Noticed significant wobble and loud squeeling from belt during spin. Found belt stretched and drive pulley out of round. Replaced belt and drive pulley. Test cycled checks good. ; used 1 Wh01x24697 (Belt), and 1 W10721967 (Cam) from stock"
We serviced a
SAMSUNG DISHWASHER
Model DW80R7060US/AA
Near Gig Harbor, WA 98335
Branden W.
Job Details: 01/12/2022
Customer concern is that dishwasher produced LC error after previous service. Found fill hose not tight at inlet valve causing very small leak. Leaked into dishwasher leak tray and set off leak sensor causing error. Tightened fill hose. Dried water in tray. Cycle tested. All checks good. NO CHARGE
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model WED9470WW1
Near Parkland, WA 98445
Branden W.
Job Details: 01/12/2022
Customer concern is that dryer starts at 38 minutes on normal auto cycle and some time later says 55 minutes. Unit running too long. Moisture sensors responsive. Temperatures in range. Airflow in yellow on meter. Cycle tested on normal cycle with normal dryness level. Unit operating as designed at this time.
We serviced a
ELECTROLUX DRYER-ELECTRIC
Model EFDG317TIW1
Near Tacoma, WA 98422
Cameron M.
Job Details: 01/12/2022
"Customer concern is that dryer makes noise during operation. Found dirty rollers, causing noise during operation. Also found loose fasteners,,causing unit to make noise during operation. Cleaned and lubed rollers. Reseated fasteners. Cycle tested unit 3x all checks good."