We serviced a
MAYTAG DRYER-ELECTRIC
Model MED3500FW0
Near McKinney, TX 75070
Jacob P.
Job Details: 07/01/2021
"Customer concern of unit making squeaking noise. Found seized idler pulley and dirty rollers. Replaced idler pulley, cleaned and lubed rollers. Test cycled, all checks ok. ; used 1 279640 (PULLEY,IDLER) from stock"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT710PAHB1
Near Tacoma, WA 98465
Branden W.
Job Details: 07/01/2021
Customer concern is that dishwasher was leaking. Then would not power on. Found loose power connection at dishwasher causing no power. Replaced wire nut. Unit powers fine. Cycle tested dishwasher. Found that disposal under sink leaks water through disposal. Advised that disposal is cause of leak. Advised to not use unit leak is repaired. No other issues found with dishwasher.
We serviced a
KENMORE DRYER-GAS
Model 11076911692
Near Dallas, TX 75228
Jacob P.
Job Details: 07/01/2021
"Customer concern of unit not heating. Found open thermal fuse causing no heat. Replaced thermal fuse. Test cycled, all checks ok. ; used 1 WP3390719 (FUSE-THRML) from stock"
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB880BW0
Near Gig Harbor, WA 98335
Branden W.
Job Details: 07/01/2021
Installed new inlet valve. Cycle tested. All checks good. Left failed part as it caused a water leak.
We serviced a
KENMORE OVEN/STOVE
Model 79070613210
Near Frisco, TX 75035
Jacob P.
Job Details: 07/01/2021
"Customer concern of unit not heating. Found weak igniter causing no ignition. Replaced igniter. Test cycled, all checks ok. ; used 1 WB13K21 (OVEN IGNITER-12' LEAD W/NUTS) from stock"
We serviced a
GE DISHWASHER
Model GDF530PSM4SS
Near Carrollton, TX 75010
Jacob P.
Job Details: 07/01/2021
"Customer concern of unit not drying dishes, tub is wet at end of cycle and rust found in bottom of tub. Unit has rinse aid. Checked water temps at sink, 120deg. Tested heating element, unit heats. No sign of rust caused by dishwasher. Unable to find any mechanical failure. Unit functioning as designed. Advised customer they will need to call into ge for further issues."
We serviced a
WHIRLPOOL RANGE
Model WFE510S0AB0
Near Gig Harbor, WA 98335
Branden W.
Job Details: 07/01/2021
"Customer concern is that after airfreight tripped circuit, range does not power on. Found only 120v to range. L1 to N 120vac, L2 to N 0vac. Reset breaker multiples times. Issue persists. Advised an electrician is need to restore proper power to range. Also advised wall outlets in kitchen should not be on same circuit as range. Found no issues with range."
We serviced a
KENMORE DRYER-ELECTRIC
Model 79680021900
Near Dallas, TX 75240
Jacob P.
Job Details: 07/01/2021
"Customer concern of long dry times. Ran air flow test, 100% plugged. Removed vent from back of dryer, found duct and internal unit vent completely plugged with lint. Removed lint from inside dryer and replaced duct. Ran air flow test again, still failed. Advised customer vent from back of dryer to outside needs to be cleaned asap. ; used 1 BTD48 (4: X 8' FLEX DUCT), and 1 MC450 (4' WORM CLAMP) from stock"
We serviced a
GE WASHER-FRONT LOA
Model GFW550SSN0WW
Near Tacoma, WA 98445
Cameron M.
Job Details: 07/01/2021
"Installed previously ordered inlet valve, cycle tested all checks good."
We serviced a
JENN-AIR OVEN-WALL
Model WW27430P
Near Dallas, TX 75248
Jacob P.
Job Details: 06/30/2021
"Installed previously ordered control board. Test cycled, all checks ok."
We serviced a
KENMORE RANGE
Model 79096123409
Near Eatonville, WA 98328
Branden W.
Job Details: 06/30/2021
Customer concern is that range does not heat. No burners or elememt operate. Found 120v L1 to N. But only 40v L2 to N. Advised that proper power is not supplied causing elements to not operate. Advised that an electrician is needed.
We serviced a
GE DISHWASHER
Model GLD4560R00SS
Near Wylie, TX 75098
Jacob P.
Job Details: 06/30/2021
"Customer concern of unit not latching. Closed door, unit latched. Test cycled ?5, all checks ok. Unable to verify complaint. Unit functioning as designed."
We serviced a
GE DISHWASHER
Model PDT825SSJ2SS
Near Dallas, TX 75206
Jacob P.
Job Details: 06/30/2021
"Installed previously ordered door catch. Test cycled, all checks ok."
We serviced a
LG DRYER-ELECTRIC
Model DLE3733W
Near Spanaway, WA 98387
Cameron M.
Job Details: 06/30/2021
Customer concern is that dryer takes multiple cycles to dry clothes. Performed airflow test (red) failed. Found clogged vent duct. Causing multiple cycles. Tested operating temperatures with vent off 160.Cleaned and calibrated moisture sensors. Advised customer dryer duct needs to be cleaned asap.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM5
Near Spanaway, WA 98387
Branden W.
Job Details: 06/30/2021
"Installed new control board, dispenser, wire harness, heater, drain pump and inlet hose adapter. Cycle tested x3. All checks good."
We serviced a
WHIRLPOOL WASHER-FRONT LOA
Model WFW87HEDC1
Near Spanaway, WA 98387
Cameron M.
Job Details: 06/30/2021
"Installed previously ordered drain pump, cycle tested all checks good."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV45H7000EW/A2 02
Near DuPont, WA 98327
Cameron M.
Job Details: 06/30/2021
"Installed previously ordered wire harness, cleaned and vacuumed inside unit. cycle tested 3x times all checks good."
We serviced a
WHIRLPOOL WALL OVEN
Model WOD51EC7AS03
Near Graham, WA 98338
Branden W.
Job Details: 06/29/2021
Customer concern is that any heating mode would just produce feature not available error. Retrieved error F1E0 (internal failure) error code. Reset per tech guide. Cycle tested both oven. All checks good.
We serviced a
GE DISHWASHER
Model GDF610PSJ2SS
Near Spanaway, WA 98387
Cameron M.
Job Details: 06/29/2021
"Installed previously ordered main control board, cycle tested all checks good."
We serviced a
KENMORE RANGE
Model 79032363411
Near Garland, TX 75041
Jacob P.
Job Details: 06/29/2021
"Customer concern of unit not heating and surface burner flames are sometimes orange. Found weak igniter causing no heat in oven. Replaced igniter. Test cycled, checks ok. Advised customer that orange flame is caused by too much oxygen in flame, can be caused by multiple things. Test cycled surface burners, all functioning as designed. ; used 1 WB13K21 (OVEN IGNITER-12' LEAD W/NUTS) from stock"
We serviced a
MAYTAG COOKTOP
Model MGC5430BDS
Near Plano, TX 75094
Jacob P.
Job Details: 06/29/2021
"Installed previously ordered spark module, spark switch, burner screws, burner knobs and orifice holders. Test cycled, all checks ok."
We serviced a
KITCHENAID DISHWASHER
Model KDFE104DSS2
Near Frisco, TX 75035
Jacob P.
Job Details: 06/29/2021
"Installed previously ordered wash pump. Test cycled, all checks ok."
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model 79681022900
Near Dallas, TX 75225
Jacob P.
Job Details: 06/29/2021
"Customer concern of unit making noise. Found worn front rollers causing noise. Replaced rollers. Test cycled, all checks ok. ; used 2 4581EL2002H (ROLLER ASSEMBLY) from stock"
We serviced a
GE DISHWASHER
Model GDWF100R10BB
Near McKinney, TX 75071
Jacob P.
Job Details: 06/28/2021
"Installed previously ordered drain pump and drain hose. Test cycled, all checks ok."
We serviced a
KENMORE RANGE
Model 79096214403
Near South Hill, WA 98374
Cameron M.
Job Details: 06/28/2021
"Installed new control, probe and overlay. Cycle tested at 350. All checks good."
We serviced a
JENN-AIR RANGE
Model JES9800BAS
Near Plano, TX 75024
Jacob P.
Job Details: 06/28/2021
"Installed previously ordered console. Test cycled, all checks ok."
We serviced a
SAMSUNG DISHWASHER
Model DW80N3030US/AA 00
Near Tacoma, WA 98444
Cameron M.
Job Details: 06/28/2021
Customer concern is that dishwasher does not start a cycle. Cycle tested numerous times in different cycles. Dishwasher operating as designed at time of service.
We serviced a
KENMORE WASHER-TOPLOAD
Model 11021102012
Near Dallas, TX 75243
Jacob P.
Job Details: 06/28/2021
"Installed previously ordered inlet valve. Test cycled ?20, all checks ok"
We serviced a
KENMORE WALL OVEN
Model 79049613317
Near Rowlett, TX 75088
Jacob P.
Job Details: 06/28/2021
"Customer concern of unit not heating. Found burnt terminal to bake element causing no heat. Replaced terminal. Test cycled, all checks ok."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWB765FFW3
Near Spanaway, WA 98387
Cameron M.
Job Details: 06/28/2021
Customer concern is that clothing stuck under agitator. Clothing removed. Unit working fine.
We serviced a
GE LAUNDRY CENTER
Model GUD27ESSM1WW
Near Grand Prairie, TX 75051
Jacob P.
Job Details: 06/25/2021
"Customer concern of unit not washing. Found debris inside cabinet that caused drive belt to fall off. Removed debris and mounted belt. Test cycled, all checks ok."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE45N5300W/A3
Near Dallas, TX 75235
Jacob P.
Job Details: 06/25/2021
"Installed previously ordered control board. Test cycled, all checks ok."
We serviced a
GE DISHWASHER
Model GDT535PSJ2SS
Near Edgewood, WA 98371
Cameron M.
Job Details: 06/25/2021
"Installed new drain pump, control board and flood switch. Cycle tested. All checks good."
We serviced a
LG DRYER-ELECTRIC
Model DLE5977S
Near Mesquite, TX 75150
Jacob P.
Job Details: 06/25/2021
"Customer concern of dryer making noise. Found no mechanical failure with dryer. Cleaned and lubed rollers and idler pulley. Advised customer that AHS does not cover noise. Unit functioning as designed, no mechanical failure."
We serviced a
GE DISHWASHER
Model GDF510PGR0BB
Near Princeton, TX 75407
Jacob P.
Job Details: 06/25/2021
"Customer concern of unit taking a long time to dry dishes. Test cycled heating element, checks ok. Found rinse aid in dispenser. Test cycled all other components, all checks ok. Unit functioning as designed."
We serviced a
GE DRYER-ELECTRIC
Model GFD55ESSN0WW
Near Wylie, TX 75098
Jacob P.
Job Details: 06/25/2021
"Customer concern of unit not turning on. Found plug slightly too far out of outlet causing no power. Seated plug fully into outlet. Test cycled, all checks ok."
We serviced a
MAYTAG DRYER-ELECTRIC
Model MEDX655DW1
Near Puyallup, WA 98373
Cameron M.
Job Details: 06/25/2021
Installed new drum seal. Cycle tested. All checks good.
We serviced a
AMANA WASHER-TOPLOAD
Model NTW4516FW2
Near South Hill, WA 98375
Cameron M.
Job Details: 06/25/2021
"Customer concern is that washer does not finish cycle. Found F7 E1 (Unable to obtain RPM) error stored. Cycle tested washer. Found failed transmission causing loud operation and oil leak into drive components. Also found actuator not sending RPM to main control. Needs new gearcase, actuator, belt and pulley kit. Declined to repair at this time."
We serviced a
GE WASHER-FRONT LOA
Model WPGT9350C0PL
Near Frisco, TX 75034
Jacob P.
Job Details: 06/24/2021
"Installed previously ordered inlet valve. Test cycled, all checks ok. Left failed part with customer."
We serviced a
GE WASHER-TOPLOAD
Model GTW720BSN0WS
Near Plano, TX 75024
Jacob P.
Job Details: 06/24/2021
"Installed previously ordered control board and accelerometer. Test cycled, all checks ok."
We serviced a
WHIRLPOOL DRYER-ELECTRIC
Model WED8500DC3
Near McKinney, TX 75070
Jacob P.
Job Details: 06/23/2021
"Installed previously ordered control board and thermistor. Test cycled, all checks ok."
We serviced a
GE DISHWASHER
Model PDT715SYN2FS
Near Frisco, TX 75034
Jacob P.
Job Details: 06/23/2021
"Installed previously ordered roller kits. Test cycled, all checks ok."
We serviced a
GE DRYER-ELECTRIC
Model GFD65GSPN0SN
Near Frisco, TX 75034
Jacob P.
Job Details: 06/23/2021
"Installed previously ordered ui board and power button. Test cycled, all checks ok."
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW7300DW1
Near Puyallup, WA 98374
Cameron M.
Job Details: 06/23/2021
Customer concern is that washer does not operate and produces F6 E3. Unit unplugged at time of service. Plugged unit in. Cycle tested numerous times. Washer operating properly at time of service. All button respond properly. Advised to call if issue returns.
We serviced a
FISHER PAYKEL DRYER-ELECTRIC
Model DEGX1 US
Near Tacoma, WA 98443
Cameron M.
Job Details: 06/23/2021
Customer concern is that dryer does not heat. Found sagging heating coil caused thermostat to trip. Replaced heating element assembly with old dryer outside at customers request. NO WARRANTYVacuumed inside of dryer. Cycle tested. All checks good.
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW8900BC0
Near Spanaway, WA 98387
Cameron M.
Job Details: 06/23/2021
Customer concern is that washer intermittently leaks from bottom left corner. Found inlet valve intermittently allowing too much pressure to detergent dispenser causing it to overflow and produce leak. Advised part is back ordered with no ETA.
We serviced a
MAYTAG DRYER-ELECTRIC
Model MEDB835DW4
Near Dallas, TX 75229
Jacob P.
Job Details: 06/23/2021
"Installed previously ordered control board. Test cycled, all checks ok."
We serviced a
KENMORE DRYER-ELECTRIC
Model 11062342511
Near Dallas, TX 75218
Jacob P.
Job Details: 06/22/2021
"Customer concern of dryer not turning on. Found open thermal fuse causing no power. Replaced thermal fuse. Test cycled temps cycling too high. Replaced operating thermostat. Test cycled, all checks ok. ; used 1 WP3392519 (FUSE-THRML), and 1 WP3387134 (THRMST-FIX) from stock"
We serviced a
GE WALL OVEN
Model PT916SR1SS
Near Plano, TX 75024
Jacob P.
Job Details: 06/22/2021
"Customer concern of condensation in display, keypad not working. Unplugged control panel from main board and reseated connection, keypad now works. Unable to find any worn seal or insulation that would cause condensation in display. Unit functioning as designed, advised customer to call back if problem persists."
We serviced a
WHIRLPOOL WASHER-FRONT LOA
Model WFW72HEDW0
Near Plano, TX 75024
Jacob P.
Job Details: 06/22/2021
"Installed previously ordered inlet valve, dispenser assy and front panel. Test cycled, all checks ok."
We serviced a
WHIRLPOOL WASHER-TOPLOAD
Model WTW5000DW2
Near Tacoma, WA 98444
Cameron M.
Job Details: 06/22/2021
Installed new suspension rods. All checks ok.
We serviced a
KENMORE WASHER-TOPLOAD
Model 79631523211
Near Tacoma, WA 98422
Cameron M.
Job Details: 06/22/2021
Customer concern is that bleach dispenser intermittently has water remaining after end of cycle. Found debris build up in dispenser causing Siphon to stop before dispenser is emptied. Cleaned dispenser. Cycle tested. All checks good.
We serviced a
GE WASHER-TOPLOAD
Model GTW220ACK6WW
Near McKinney, TX 75070
Jacob P.
Job Details: 06/22/2021
"Customer concern of unit not advancing through cycles. Found lid lock ohms out of range causing no lid lock. Also found water supply hoses backwards. Swapped inlet hoses and replaced lid lock. Test cycled, all checks ok. ; used 1 WH08X31577 (LID LOCK QUICK RELEA) from stock"
We serviced a
WHIRLPOOL DISHWASHER
Model GU2700XTSS1
Near Fairview, TX 75069
Jacob P.
Job Details: 06/22/2021
"Installed previously ordered door seal. Test cycled, all checks ok."
We serviced a
MAYTAG DRYER-ELECTRIC
Model MED5500FC0
Near Lakewood, WA 98498
Cameron M.
Job Details: 06/22/2021
"Customer concern is that dryer was beeping randomly then stopped turning on. Found 240v to dryer, 120vac to main board, 5 and 12vdc from main board to user board. No response from user board. Needs new user interface assembly. Left unit unplugged. Declined tomrepair at this time."
We serviced a
GE DRYER-ELECTRIC
Model GFD55ESSN0WW
Near Frisco, TX 75034
Jacob P.
Job Details: 06/22/2021
"Installed previously ordered terminal block and customer provided power cord and vent. Test cycled, all checks ok."
We serviced a
GE WALL OVEN
Model PT916S0M1SS
Near Frisco, TX 75034
Jacob P.
Job Details: 06/22/2021
"Customer concern of oven temps too low. Found oven temps low inside oven. Recallibrated oven temps. Test cycled, all checks ok."
We serviced a
KENMORE WASHER-TOPLOAD
Model 11028102310
Near Tacoma, WA 98404
Cameron M.
Job Details: 06/22/2021
Customer concern is that washer does not spin and produces F51 error. Found loose motor rotor bolt causing rotor to slide away from stator causing error and no spin. Secured bolt with loctite. Cycle tested. All checks good.
We serviced a
LG WASHER-TOPLOAD
Model WT7300CW
Near Graham, WA 98338
Cameron M.
Job Details: 06/21/2021
"Installed sears supplied user interface and main ,cycle tested all checks good."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE45R6300V/A3
Near Orting, WA 98360
Cameron M.
Job Details: 06/21/2021
Installed new main control. Cycle tested. All checks good.
We serviced a
GE WASHER-TOPLOAD
Model GTW840CPN0DG
Near Little Elm, TX 75068
Jacob P.
Job Details: 06/21/2021
"Customer concern of unit not filling with hot water. Found hot water inlet hose screen plugged causing no hot water fill. Cleaned inlet hose screen. Test cycled, all checks ok."
We serviced a
FRIGIDAIRE RANGE
Model FFGF3047LSF
Near Bonney Lake, WA 98391
Cameron M.
Job Details: 06/21/2021
"Installed new burner, ignitor and flame spreader. Tested to 350. All checks good."
We serviced a
GE DISHWASHER
Model GDT580SMF2ES
Near Farmers Branch, TX 75234
Jacob P.
Job Details: 06/21/2021
"Customer concern of unit not drying dishes. Found thermistor ohms out of range causing no heat. Replaced thermistor. Test cycled, unit now heats. Also found no rinse aid in unit. Advised customer that rinse aid is required for proper washing and drying results. Unit functioning as designed. ; used 1 WD21X10519 (SWITCH FLOOD) from stock"
We serviced a
KITCHENAID DISHWASHER
Model KUDS01FLBL6
Near Dallas, TX 75225
Jacob P.
Job Details: 06/21/2021
"Customer concern of unit not working. Found water supply to dishwasher turned off causing no wash. Turned water supply on. Test cycled, all checks ok."
We serviced a
GE DISHWASHER
Model PDT715SYN3FS
Near Frisco, TX 75033
Jacob P.
Job Details: 06/17/2021
"Customer concern of unit leaving white spots on dishes and inside tub. Advised customer phosphate free detergents can leave residue on dishes and inside machine. Found no rinse aid in unit, advised customer rinse aid is required for proper wash and dry results. Unit functioning as designed."
We serviced a
GE DISHWASHER
Model GDF530PSM4SS
Near Carrollton, TX 75010
Jacob P.
Job Details: 06/17/2021
"Customer concern of unit having poor wash and dry results and some options don't work. Advised customer that not all options are available on every cycle. Test cycled heating element, checks ok. Found no rinse aid in unit. Advised customer that rinse aid is required for proper wash and dry results. Unit functioning as designed."
We serviced a
GE DISHWASHER
Model GSD3400G00WW
Near Graham, WA 98338
Cameron M.
Job Details: 06/17/2021
Installed new sump/motor assembly. Cycle tested x5. All checks good. Unable to remove dishwasher as there is not clearance at tile counter edge.
We serviced a
GE RANGE
Model JGB281SER5SS
Near Spanaway, WA 98387
Cameron M.
Job Details: 06/17/2021
Customer concern is that range does not operate. Found gas supply valve turned off causing unit to not work. Turned gas on. Cycle tested oven to 350. All burners operating. Found no issues. Left gas valve turned on at customers request.
We serviced a
KITCHENAID OVEN-WALL
Model KEBS209BSS013
Near Dallas, TX 75229
Jacob P.
Job Details: 06/17/2021
"Installed previously ordered transformer. Test cycled, all checks ok."
We serviced a
GE DISHWASHER
Model GLDA696MSS
Near Tacoma, WA 98445
Cameron M.
Job Details: 06/17/2021
"Installed new door hinges, door latch and spray arms. Cycle tested. Dishwasher operating as designed."
We serviced a
GE DISHWASHER
Model GDT580SMF6ES
Near Auburn, WA 98092
Cameron M.
Job Details: 06/17/2021
Customer concern is that dishwasher does not power on. Found breaker turned off causing unit to not power. Turned breaker on. Cycle tested. Found disposal still had factory plug in causing water to drain from airgap. Removed plug. Cycle tested. All checks good.
We serviced a
KENMORE WASHER-TOPLOAD
Model 11020952992
Near Dallas, TX 75217
Jacob P.
Job Details: 06/17/2021
"Customer concern of unit leaking. Found bleach dispenser cup clogged with debris causing overflow. Cleaned debris. Test cycled, all checks ok."
We serviced a
GE DISHWASHER
Model PDT715SYN3FS
Near Rockwall, TX 75087
Jacob P.
Job Details: 06/17/2021
"Customer concern of rack broken. Found right mid rack rivets broken causing rack too fall. Called GE tech support, GE deemed unit not repairable. Advised customer that they will need to call in to customer relations with case number. Case #06037103"
We serviced a
GE DISHWASHER
Model GDF530PSM5SS
Near Rowlett, TX 75089
Jacob P.
Job Details: 06/17/2021
"Customer concern of unit not washing. Found wash pump unplugged causing no wash. Plugged wash pump in. Test cycled, all checks ok."
We serviced a
KENMORE WASHER-FRONT LOA
Model 11045862400
Near Bonney Lake, WA 98391
Cameron M.
Job Details: 06/17/2021
Installed new drain pump and hose. Cycle tested x4. No leaks. Drains properly. Cycle tested with load in rinse and spin. All checks good.
We serviced a
KENMORE RANGE
Model 79094462700
Near Orting, WA 98360
Cameron M.
Job Details: 06/17/2021
"Installed new door cap, handle, trim and screws. All checks good."
We serviced a
MAYTAG WASHER-TOPLOAD
Model MVWX655DW1
Near Puyallup, WA 98374
Cameron M.
Job Details: 06/17/2021
Installed new water valves. Cycle tested. All checks good
We serviced a
LG DISHWASHER
Model LDF5545ST
Near Spanaway, WA 98387
Cameron M.
Job Details: 06/17/2021
Installed new main control and door latch. Cycle tested. Found airgap not draining into disposal. Cleaned hose from airgap to disposal. All checks good
We serviced a
GE DRYER-ELECTRIC
Model GFD55ESSN0WW
Near Wylie, TX 75098
Jacob P.
Job Details: 06/17/2021
"Customer concern of unit turning off after running for a few minutes. Found moisture sensor unplugged causing unit to turn off early. Plugged in moisture sensor. Test cycled, all checks ok."
We serviced a
SAMSUNG WASHER-TOPLOAD
Model WA52M7750AW/A4
Near Graham, WA 98338
Cameron M.
Job Details: 06/16/2021
Installed new lid lock. Cycle tested lock x20. All checks good.
We serviced a
KENMORE DISHWASHER
Model 66512793K313
Near Eatonville, WA 98328
Cameron M.
Job Details: 06/16/2021
Installed new dispenser. Cycle tested. All checks good.
We serviced a
AMANA DRYER-ELECTRIC
Model n/a
Near Dallas, TX 75252
Jacob P.
Job Details: 06/16/2021
Customer canceled call
We serviced a
AMANA DISHWASHER
Model ADB1400PYS5
Near Roy, WA 98580
Cameron M.
Job Details: 06/16/2021
Customer concern is that dishwasher will start a cycle but intermittently will not complete the cycle without pressing start button mid cycle. Cycle tested. Unable to get unit to stop in cycle. Did find loose door latch that could be causing issue. Repositioned and tightened latch. Also found F6 E6 (water too cold) error stored. This couod cause unit to stop. Advised to run sink until hot before starting dishwasher. Advised to call if issue persists.
We serviced a
KITCHENAID DISHWASHER
Model KUDE70FXSS1
Near Dallas, TX 75225
Jacob P.
Job Details: 06/16/2021
"Customer concern of unit leaking. Found supply hose to inlet valve loose causing slow leak. Tightened supply hose. Test cycled, all checks ok."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DVE45R6100P/A3
Near Dallas, TX 75225
Jacob P.
Job Details: 06/16/2021
"Installed previously ordered control board. Test cycled, all checks ok."
We serviced a
GE DRYER-ELECTRIC
Model GTD45EASJ2WS
Near Princeton, TX 75407
Jacob P.
Job Details: 06/15/2021
"Customer concern of unit not starting. Found corroded contacts in door switch causing no start. Cleaned contacts. Test cycled, all checks ok."
We serviced a
WHIRLPOOL RANGE
Model WFG231LVS0
Near Spanaway, WA 98387
Cameron M.
Job Details: 06/15/2021
Customer concern is that oven does not work. Cycle tested ignitor x40. Tested to 350 degrees. Unable to reproduce unit not working at time of service. Advised to call if issue returns.
We serviced a
SAMSUNG DISHWASHER
Model DW7933LRASR/AA
Near Puyallup, WA 98372
Cameron M.
Job Details: 06/15/2021
Customer concern is that dishwasher does not run a cycle. Found unit gettimg overfill error and not washing. Found debris in case brake sensor causing unit to trip overfill sensor and not run. Cleaned case brake. Cycle tested. All checks good.
We serviced a
GE LAUNDRY CENTER
Model GUD27ESSM1WW
Near Frisco, TX 75035
Jacob P.
Job Details: 06/15/2021
"Customer concern of unit banging around. Test cycled empty, no issues. Test cycled with a load, no issues. Advised that unit shaking while getting up into higher speed spin is normal. Unit functioning as designed."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV48H7400EW/A2 02
Near Bonney Lake, WA 98391
Cameron M.
Job Details: 06/15/2021
"Customer concern is that dryer powers on but does not tumble. Found failed idler pulley causing unit to not tumble. Installed new idler pulley, cycle tested all checks good. ; used 1 DC93-00634A (IDLER ASSEMBLY) from stock"
We serviced a
GE WASHER-TOPLOAD
Model GTW840CPN0DG
Near Lewisville, TX 75067
Jacob P.
Job Details: 06/15/2021
Customer concern of detergent tank empty light on. Found light off upon arrival. Unit functioning as designed.
We serviced a
KENMORE WASHER-TOPLOAD
Model 11022352511
Near Tacoma, WA 98404
Cameron M.
Job Details: 06/15/2021
Customer concern is that washer makes noise in spin. Found rock lodged between drive pulley and guard causing noise. Removed rock. Cycle tested. All checks good.
We serviced a
KENMORE WASHER-FRONT LOA
Model 79641583410
Near ,
Cameron M.
Job Details: 06/15/2021
"Customer concern is that washer leaks a lot of water from under unit. Found airvent hose popped off tub from out of balance load , causing leak . Reseated hose cycle tested all checks good."
We serviced a
GE DRYER-ELECTRIC
Model GFDS140ED1WW
Near Plano, TX 75075
Jacob P.
Job Details: 06/14/2021
"Installed previously ordered front bearing. Test cycled, all checks ok."
We serviced a
GE WASHER-TOPLOAD
Model GTW500ASN0WS
Near Lewisville, TX 75056
Jacob P.
Job Details: 06/14/2021
"Installed previously ordered control board. Test cycled, all checks ok."
We serviced a
FRIGIDAIRE WASHER-FRONT LOA
Model LAFW8000LW0
Near Dallas, TX 75205
Jacob P.
Job Details: 06/14/2021
"Customer concern of unit leaking. Found dirty door glass and door seal causing leak out front of unit. Cleaned door glass and seal. Test cycled, all checks ok."
We serviced a
SAMSUNG WASHER-FRONT LOA
Model WF45R6100AP/US
Near Bonney Lake, WA 98391
Cameron M.
Job Details: 06/14/2021
Customer concern is that washer walks in spin cycle. Cycle tested with a load of towels. Washer is operating as designed. Found pedestal is allowing a lot of flex from side to side as washer spins allowing unit to bounce and eventually walk. Issue is with pedestal not washer. Advised pedestal is not serviceable.
We serviced a
KENMORE WASHER-FRONT LOA
Model 11022342511
Near Dallas, TX 75224
Jacob P.
Job Details: 06/14/2021
"Performed pm check on washer, all checks ok."
We serviced a
SAMSUNG DRYER-ELECTRIC
Model DV48J7770EP/A2 02
Near Graham, WA 98338
Cameron M.
Job Details: 06/14/2021
Installed new door latch and catch. All checks good.
We serviced a
GE WASHER-TOPLOAD
Model GTW335ASN1WW
Near Garland, TX 75041
Jacob P.
Job Details: 06/14/2021
"Customer concern of unit not filling with cold water. Found inlet hoses swapped causing unit to fill with incorrect water temperature. Swapped inlet hoses. Test cycled, all checks ok."