Skip to main content
Master certified techniciansUpfront pricingService you can count on
RPS Appliance RepairRPS Appliance Repair

From our technicians

What happened. What we found. What we repaired.

A symptom tells part of the story. Here’s how our technicians found the cause and checked the result on real appliance repairs.

Clear filters

Showing 133 to 144 of 168 repair stories

Sachse, TXMaytag dryer not heating: heating element repair in Sachse

A Maytag dryer in Sachse was not heating. The technician found an open heat element, replaced it, and confirmed the dryer was heating again during the visit.

Read the repair story →
Irving, TXMaytag Washer Would Not Complete Cycle: Drain Pump Connection Repaired in Irving

A Maytag washer in Irving was not completing its cycles. The technician identified and corrected a loose drain pump connection, then tested the washer to confirm proper operation.

Read the repair story →
Tacoma, WAGE dishwasher rack wheel repair in Tacoma

A GE dishwasher in Tacoma was experiencing issues with the lower rack wheels, cleaning performance, and door latch. The technician identified the issues, completed the necessary repairs, and tested the dishwasher to verify proper operation.

Read the repair story →
Dallas, TXWhirlpool washer would not complete cycle in Dallas

A Whirlpool washer in Dallas was not completing its cycles. Diagnostic testing identified a faulty actuator and motor capacitor. The technician replaced both components and performed a full function test, confirming that the washer was operating properly at the time of service.

Read the repair story →
ROCKWALL, TXWhirlpool refrigerator cooling issue repaired in Rockwall

A Whirlpool refrigerator in Rockwall was not cooling. The technician found a defrost problem, replaced the noted parts, and verified the unit was cooling before leaving.

Read the repair story →
McKinney, TXMaytag Washer Would Not Stop Filling: Water Valve Repair in McKinney

A Maytag washer in McKinney would not stop filling. The technician found the water valve stuck open, replaced it, and confirmed the washer was working at the time of service.

Read the repair story →
Puyallup, WALG Microwave Not Heating: High-Voltage Repair in Puyallup

An LG microwave in Puyallup was reported to be operating without heating. The technician replaced the faulty high-voltage components and tested the microwave, confirming that it was heating and operating properly at the time of service.

Read the repair story →
Sulphur Springs, TXGE Washer Not Draining: Control Board and Drain Pump Repair in Sulphur Springs

A GE washer in Sulphur Springs was not draining properly. The technician replaced the failed drain pump and main control board, then tested the washer using a rinse and spin cycle. The unit was confirmed to be operating normally at the time of service.

Read the repair story →
Sulphur Springs, TXWhirlpool Refrigerator Water Dispenser Repair in Sulphur Springs

A Whirlpool refrigerator in Sulphur Springs was experiencing an issue with the water dispenser stopping after dispensing only a partial cup of water. The technician replaced the filter housing and tested the dispenser, confirming that water flowed normally after the repair.

Read the repair story →
Carrollton, TXSamsung Washer Not Spinning Out Clothes: Suspension Repair in Carrollton

A Samsung washer in Carrollton was not spinning clothes properly. Diagnostic testing indicated an issue with the suspension rods. The necessary repairs were completed, and the washer was tested during the final service visit.

Read the repair story →
Quinlan, TXGE Washer Basket Not Spinning: Inverter Board Repair in Quinlan

A GE washer in Quinlan would not spin the basket normally. Inspection pointed to the inverter board and motor circuit, and the inverter board was replaced before the washer was tested again.

Read the repair story →
Bonney Lake, WAMaytag washer not draining: wire harness repair in Bonney Lake

A Maytag washer in Bonney Lake was not draining or finishing cycles. The technician found a worn open wire harness to the drain motor, replaced the harness, and tested the washer afterward.

Read the repair story →